Abstract:Ni-rich cathode (Ni > 0.8) provides a low-cost and high-energy-density solution to the next-generation lithium-ion batteries. Unfortunately, severe capacity fading of Ni-rich cathode caused by the interfacial and bulk structural degradation impeded its application. Herein, Zr doping and Li6Zr2O7 coating are applied to a Ni-rich LiNi0.83Co0.12Mn0.05O2 (NCM) layered cathode material, and the modified material exhibits excellent cycle stability. The 1%Zr-NCM cathode material maintains a discharge capacity of 173.9 mAh g–1 at 1 C after 200 cycles in the 2.5–4.3 V voltage range at 25 °C, corresponding to a capacity retention of 94.6%; however, the unmodified NCM only delivers 129.9 mAh g–1 (capacity retention 68.6%). The synergistic effect of bulk Zr doping and surface Li6Zr2O7 coating improves the cycle stability of the Ni-rich material. Zr doped into the bulk could form a strong Zr–O bond to stabilize the layered structure, and Zr located in the Li layer can act as a pillar to maintain the layered structure and reduce Li+/Ni2+ mixing. In addition, the Li6Zr2O7 coating layer can also play a dual role in promoting Li+ migration and suppressing surface side reactions. This work demonstrates that sufficiently utilizing zirconium to enhance the electrochemical performance of cathode materials is a feasible and promising strategy.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.0c01851?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.0c01851</a>.Rietveld refinement results; SEM images and EDS mapping of precursor and Zr-modified precursor; linear sweep EDS of 1%Zr-NCM; EDS mapping of 0.5%Zr-NCM and 1%Zr-NCM; XPS spectra; rate capability; and XRD results after cycling test (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.0c01851/suppl_file/ae0c01851_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Direct Electrochemical Preparation of Ni-Zr Alloy from Mixture Oxides in LiCl Molten Salt

Preparation of Ni3Sn2 Alloy Negative Electrode for Lithium-Ion Batteries by Electro-Deoxidization in Molten Salt

Direct Electrolytic Preparation of Cerium/nickel Hydrogen Storage Alloy Powder in Molten Salt

The influence of relative content of Ti and Zr on the electrochemical behavior of Laves phase alloy

Direct Electrolytic Preparation of La0.5Ce0.5Ni5 Alloy in Molten Salt

Synthesis of LiNiO2 cathode materials with homogeneous Al doping at the atomic level

The effect of partial substitution of Ti with Zr, Cr or V in the Mg35Ti10Ni55 electrode alloy on its electrochemical performance

Bulk Nanostructure Formation Directly From The Multicomponent Alloy Melt

Oxidation of amorphous Ni–Zr alloys studied by XPS, UPS, ISS and XRD

Electrochemical Co-Reduction Extraction of Neodymium in LiCl-KCl-ZnCl2 Molten Salt System

A modified ZrO2-coating process to improve electrochemical performance of Li(Ni1/3Co1/3Mn1/3)O2

Effect of Lithium to Zirconium Ratio on Microstructure and Electrochemical Performances of LZO Modified LiNi0.8Co0.1Mn0.1O2 Cathode Materials

Electrochemical behavior of Zr(IV) and co-reduction synthesis of Al-Zr alloys in KF-AlF3-Al2O3-ZrO2 molten salt

Manipulation of the LiZn Alloy Process toward High-Efficiency Lithium Metal Anodes

Electrochemical Behavior of Dy(III) and Formation of Dy-Zn Alloy by Co-Reduction with Zn(II) in Eutectic NaCl-KCl Melts

Effect of Annealing Temperature on the Microstructure and Electrochemical Performance of Li2ZrO3-modified Ni-rich NCM811

Preparation of a (Ca,Sr,Ba)ZrO3 Crucible by Slip Casting for the Vacuum Induction Melting of NiTi Alloy

Enhancing the structural stability of Ni-rich layered oxide cathodes with a preformed Zr-concentrated defective nanolayer.

Utilizing Diverse Functions of Zirconium to Enhance the Electrochemical Performance of Ni-Rich Layered Cathode Materials

Electrochemical Extraction of Samarium from LiCl-KCl Melt by Forming Sm-Zn Alloys

Activation behaviour of mechanically Ni-coated Zr-based laves phase hydride electrode