Abstract:A novel method, ethanol solvent‐assisted chemical deposition (S‐CBD), is developed to control the film's growth rate higher than its nucleation rate, thereby enhancing the grain size and electrical properties of the Sb2S3 film and boosting device performance through this self‐regulation of the precursor solution. Antimony sulfide (Sb2S3) has attracted extensive attention due to its excellent photoelectric characteristics, including a high absorption coefficient (α > 104 cm−1) and a suitable bandgap (≈1.7 eV). However, due to its Q1D (quasi‐1D) structure, numerous deep‐level defects are identified in the Sb2S3 film, limiting the device's performance, and necessitating more efforts to overcome this situation. In this context, an ethanol solvent‐assisted chemical bath deposition (S‐CBD) strategy, a novel high‐quality thin film manufacturing technique is presented that modifies the supersaturation of the precursor solution by varying the boiling point and solvent polarity. This approach enables the effective regulation of the correlation between the crystal nucleation and growth rates, resulting in Sb2S3 films with large grains (≈4.25 μm, 37.5% ethanol), excellent crystallinity, well‐oriented structures (TC(211)/TC(020) = 2.39), low defect density, and prolonged carrier lifetimes (τAve ≈ 12.1 ns). Consequently, the final Sb2S3‐based solar device (FTO/CdS/Sb2S3/Spiro‐OMeTAD/Au) shows significant improvements in both FF (61.63%) and JSC (17.61 mA cm−2), yielding an excellent power conversion efficiency (PCE) of 7.84%. This research gives particular insights into the growth mechanism of high‐quality Sb2S3 thin films by CBD method as well as a potential route for enhancing Sb2S3 solar cell performance.

One–step Synthesis of Cu3BiS3 Thin Films by a Dimethyl Sulfoxide (dmso)–based Solution Coating Process for Solar Cell Application

Synthesis and Characterization of Hydrazine Solution Processed Cu12Sb4S13 Film

Fabrication of phase-pure and large-grained Cu3BiS3 films by a two-stage process for thin film solar cells

Preparation and Characterization of Cuins2 Thin Films for Solar Cells by Chemical Bath Deposition

Chemical synthesis of Cu(In) metal inks to prepare CuInS2 thin films and solar cells

Colloidal synthesis of zincblende Cu3InSnS5 nanocrystals and their application in the thin-film solar cell

Low-cost Fabrication of Cu 2 ZnSnS 4 Thin Films for Solar Cell Absorber Layers

Solution‐Processed Compact Sb 2 S 3 Thin Films by a Facile One‐Step Deposition Method for Efficient Solar Cells

Non-toxic Cu 3 BiS 3 thin film solar cells with Al doped TiO 2 as electron-transport layers

Bismuth Complex Controlled Morphology Evolution and CuSCN-Induced Transport Improvement Enable Efficient BiI3 Solar Cells

Solution-Processed Air-Stable Copper Bismuth Iodide for Photovoltaics

Co‐Evaporated CuSbSe2 Thin Films for Solar Cells

Aqueous-Solution-Based Approach Towards Carbon-Free Sb2 S3 Films for High Efficiency Solar Cells.

Antimony Doping of CsBi 3 I 10 for Tailoring the Film Morphology and Defects toward Efficient Lead-Free Thin-Film Solar Cells

CuSbS2 As a Promising Earth-Abundant Photovoltaic Absorber Material: A Combined Theoretical and Experimental Study

A promising photovoltaic material Cu2MnSn(S,Se)4: Film growth and its application in solar cell

Sb2Se3 solar cells employing metal-organic solution coated CdS buffer layer

Bi2S3‐Cu3BiS3 Mixed Phase Interlayer for High‐Performance Cu3BiS3‐Photocathode for 2.33% Unassisted Solar Water Splitting Efficiency

Self‐Regulated Growth of Large‐Grain Sb2S3 Thin Films for High‐Efficiency Solar Cells

Solution‐Crystalized AgBiS2 Films for Solar Cells Generating a Photo‐Current Density Over 31 mA cm−2

A Review of Cu3BiS3 Thin Films: A Sustainable and Cost-Effective Photovoltaic Material