Abstract:In some circumstances, hybrid polymer microfluidic chips composed of both elastic, gas-permeable polydimethylsiloxane (PDMS) and rigid plastics are needed. However, it is quite difficult to bond PDMS irreversibly to plastics such as polystyrene (PS). In this article, a facile method for irreversible bonding of PDMS to PS was proposed based on UV/O-3-assisted surface modification in combination of surface silanization. Firstly, a PS sheet was exposed to UV/O-3 to produce oxygen-containing polar moieties, such as hydroxyl and carboxylic acid, on its surface. Secondly, the UV/O-3 treated PS sheet was silanized with (3-aminopropyl)triethoxysilane (APTES) via the reaction between the oxygen-containing polar moieties on the PS surface and the molecules of APTES. Thirdly, the silanized-PS sheet and the PDMS substrate with micro channel network were treated with UV/O-3 again to generate silanol moieties on both surfaces. Finally, the UV/O-3 treated PDMS was immediately brought intimate contact with the UV/O-3 treated silanized-PS, and irreversible bonding of PDMS with PS occurred after putting the PDMS-PS complex at room temperature for 1 h through the condensation reaction between silanol moieties. Contact angle measurement, X-ray photoelectron spectroscopy, total reflection Fourier transformation infrared spectrometer were applied to characterize the surface chemistry of the PS during the UV/O-3 treatment and silanization. The hybrid PDMS-PS microfludic chips prepared with the established method can bear a gas pressure higher than 0.5 MPa and a water stream at a flow rate higher than 170 mu L/min (the test channels were 2.5 cm in the length, 50 mu m in the width, 200 mu m in the depth). A hybrid PDMS-PS microfluidic chip composed of gas-permeable PDMS substrate with channel network and excellently biocompatible PS cover sheet was fabricated for cell culture. The experimental results showed that HeLa cells cultured in the hybrid PDMS-PS microchip grew much better than those cultured in the full PS microchip, and slightly better than those in the full PDMS microchip.

A New Method for Polydimethylsiloxane (PDMS) Microfluidic Chips to Maintain Vacuum-Driven Power Using Parylene C

Propidium Monoazide Pretreatment on a 3D-Printed Microfluidic Device for Efficient PCR Determination of ‘liveversusdead’ Microbial Cells

An Approach for Irreversible Bonding of PDMS-PS Hybrid Microfluidic Chips at Room Temperature

A Silicon-Based PDMS-PEG Copolymer Microfluidic Chip for Real-Time Polymerase Chain Reaction Diagnosis

Complete Prevention of Bubbles in a PDMS-Based Digital PCR Chip with a Multifunction Cavity

A PDMS-based Digital PCR Chip with Vacuum Aspiration and Water-Filling Cavity Integrated for Sample Loading and Evaporation Reduction

Syringe-assisted Point-of-care Micropumping Utilizing the Gas Permeability of Polydimethylsiloxane

Polymer Monolith-Integrated Multilayer Poly(Dimethylsiloxane) Microchip for Online Microextraction and Capillary Electrophoresis

Ultraviolet Sealing and Poly(dimethylacrylamide) Modification for Poly(dimethylsiloxane)/glass Microchips

A Positive Pressure-Driven PDMS Pump for Fluid Handling in Microfluidic Chips

Fabrication of Micro Pneumatic Valves with Double-Layer Elastic Poly(dimethylsiloxane) Membranes in Rigid Poly(methyl Methacrylate) Microfluidic Chips

Overcoming bubble formation in polydimethylsiloxane-made PCR chips: mechanism and elimination with a high-pressure liquid seal

Hydrophilic Biopolymer Grafted on Poly(dimethylsiloxane) Surface for Microchip Electrophoresis.

A nanoliter self-priming compartmentalization chip for point-of-care digital PCR analysis

The effect of the surface passivation on polymerase chain reaction inside a continuous flow microfluidic chip

A Rigid Poly(dimethylsiloxane) Sandwich Electrophoresis Microchip Based on Thin‐casting Method

A self-digitization chip integrated with hydration layer for low-cost and robust digital PCR

A Self-Priming Microfluidic Chip with Cushion Chambers for Easy Digital PCR

Bubble generation and mechanism in polydimethylsiloxane based polymerase chain reaction chip

Surface Modification Of Poly(Dimethylsiloxane) Microfluidic Chips By Treatment In An Oxygen Atmosphere

A Microfluidic Chip Based on Surfactant-Doped Polydimethylsiloxane (PDMS) in a Sandwich Configuration for Low-Cost and Robust Digital PCR