Abstract:Cost-effective and environmentally friendly sorbents were created for capturing CO 2 by incorporating monoethanolamine (MEA) and tetraethylenepentamine (TEPA) onto a microporous activated carbon (AC) material. The application of a KOH reagent enhanced the surface area and pore volume of the carbon material. The BET, SEM, EDX, and FTIR techniques were employed to analyze the structural and surface properties of the developed samples. Raw AC possessed the highest surface area and largest micropore volume equal to 786 m 2 /g and 0.33 cm 3 /g, respectively. The amine impregnation increased the nitrogen content of the carbon material, but it also significantly reduced the BET surface area and total pore volume, which are primarily responsible for physically adsorbing CO 2 towards ACs. The CO 2 adsorption performance of the raw and impregnated ACs was experimentally evaluated using thermogravimetric analysis (TGA) at different adsorption temperatures (25 and 50 °C) and CO 2 concentrations (10 and 90 vol.%). The findings demonstrated that the raw AC exhibited the highest capacity for CO 2 adsorption. Specifically, at a temperature of 25 °C and pressure of 1 bar (10 vol.% CO 2 , N 2 balance), the raw AC achieved an uptake of 1.2 mmol/g, which was 60.3% and 79.3% higher compared to the CO 2 uptake of MEA-AC (0.5 mmol/g) and TEPA-AC (0.3 mmol/g), respectively. It is surprising that the combined uptake of CO 2 + H 2 O increased by 12.5 and 23.4 wt.% (equivalent to 7 and 13 mmol/g) for MEA-AC and TEPA-AC, respectively, when humid flue gas was taken into account under the conditions of 50 °C, with 10 vol.% CO 2 , 4 vol.% H 2 O, and N 2 balance. These results indicate that the presence of H 2 O facilitates the chemisorption of CO 2 by the novel and highly promising carbon-based sorbent prepared in this study, leading to an increased capacity for adsorbing CO 2 under water vapor containing flue gases.

CO2 adsorption and desorption performance of waste ion-exchange resin-based activated carbon

Optimal Activation of Porous Carbon for High Performance CO2 Capture

Thermodynamics and Regeneration Studies of CO2 Adsorption on Activated Carbon

Cost-effective carbon-based amine adsorbents for carbon capture: Equilibrium, kinetics and selectivity

Porous activated carbons derived from waste sugarcane bagasse for CO2 adsorption

Hierarchical Pore Structure of Activated Carbon Fabricated by CO2/microwave for Volatile Organic Compounds Adsorption

Superior CO2 Adsorption on Pine Nut Shell-Derived Activated Carbons and the Effective Micropores at Different Temperatures

Performance of CO2 Adsorption on Modified Activated Carbons Derived from Okara Powder Waste: Impacts of Ammonia Impregnation

PREPARATION AND CHARACTERISTICS OF CARBONACEOUS ADSORBSENTS OBTAINED FROM WASTE CATION-EXCHANGE RESINS

Highly Selective CO2 Capture on Waste Polyurethane Foam-Based Activated Carbon

Activated Carbons Prepared from Peanut Shell and Sunflower Seed Shell for High CO2 Adsorption

Synthesis and characterisation of K2CO3-activated carbon produced from distilled spent grains for the adsorption of CO2

Ultra-microporous cotton fiber-derived activated carbon by a facile one-step chemical activation strategy for efficient CO 2 adsorption

Activated carbons and amine-modified materials for carbon dioxide capture — a review

Study on the adsorption rate of anion exchange absorbents for capturing carbon dioxide in ambient air

CO2 Absorption over Ion Exchange Resins: the Effect of Amine Functional Groups and Microporous Structures

Carbon Dioxide Adsorption over Activated Biocarbons Derived from Lemon Peel

Systematic study of dynamic CO2 adsorption on activated carbons derived from different biomass

Porous carbon based on polyvinylidene fluoride: Enhancement of CO2 adsorption by physical activation

The effect of humidity on the enhanced CO2 adsorption of amine-functionalized microporous activated carbon

Tuning porosity of coal-derived activated carbons for CO2 adsorption