Abstract:Aluminum casting alloys have properties which are of great industrial interest, such as low density, good corrosion resistance, high thermal and electrical conductivities, good combination of mechanical properties, good workability in machining processes and mechanical forming. Currently, these alloys are produced in various systems and dozens of compositions. In this investigation, a mutual interaction of thermal parameters, scale of the dendritic microstructure, intermetallic compounds (IMCs), microhardness and tensile properties/fracture characteristics of a casting Al–7wt%Si–3wt%Cu–0.3wt%Fe alloy was analyzed. Solidification experiments were developed using a furnace that promoted horizontal growth under transient heat flow conditions. Then, growth rate (VL), cooling rate (CR), and local solidification time (tSL) were determined from measured temperature profiles. Secondary dendritic spacings (λ2), Si particles, Fe-rich and Al2Cu intermetallic phases were characterized by optical and SEM microscopy, as well as the area mapping and point-wise EDS microanalysis. Hence, the interrelations involving Vickers microhardness (HV), yield strength (σYS), ultimate tensile strength (σUTS) and elongation (E%) with microstructural features were evaluated by mathematical equations. IMCs as well as morphologies of Si were also analyzed in the fracture regions. In addition, the experimental growth law of λ2 = f(tSL) proposed in this study was compared with a predictive theoretical model reported in the literature for multicomponent alloys. It was observed that areas that tend to grow faster (lowest λ2 values) were associated with the highest σUTS and E% values, while HV and σYS properties were not affected by the thermal and microstructural parameters (CR and λ2). In addition, less extensive cleavage planes accompanied by small dimples in were observed in fractured samples with lower λ2 values.

From Solidification Processing to Microstructure to Mechanical Properties: A Multi-scale X-ray Study of an Al-Cu Alloy Sample

Semi-solid Compression of Nano/micro-Particle Reinforced Al-Cu Composites: an in Situ Synchrotron Tomographic Study

Dynamics of Solidification and Microstructure Evolution in Undercooled Co-Cu-Alloys with Metastable Miscibility Gap

Microstructure Evolution and Mechanical Property of Quaternary Cu-7%Al-4%Ni-2.5%Mn Alloy Solidified Within Ultrasonic Field

In Situ and Real-Time Observation of the Solidification Process of Al-20 Mass%Cu Alloy by Synchrotron X-Ray Radiography

Solidification Crack Propagation and Morphology Dependence on Processing Parameters in AA6061 from Ultra-High-speed X-Ray Visualization

In Situ Investigation of Microstructural Evolution and Intermetallic Compounds Formation at Liquid Al/Solid Cu Interface by Synchrotron X-ray Radiography

Unsteady-State Horizontal Solidification of an Al–Si–Cu–Fe Alloy: Relationship Between Thermal Parameters and Microstructure with Mechanical Properties/Fracture Feature

Multi-scale Study of Microstructure Evolution in Hot Extruded Nano-Sized TiB2 Particle Reinforced Aluminum Composites

Multiscale Ductile Fracture Integrating Tomographic Characterization and 3-D Simulation

3D characterization and modeling of low cycle fatigue damage mechanisms at high temperature in a cast aluminum alloy

Multi-dimensional Characterization and Controlling of Microstructure Evolution During Solidification of Metallic Alloys

Microstructure evolution of Al-matrix composites during semi-solid compressive deformation revealed by synchrotron <i>in situ</i> CT

Tensile Deformation And Fracture Behaviors Of A Nickel-Based Superalloy Via In Situ Digital Image Correlation And Synchrotron Radiation X-Ray Tomography

Three Dimensional (3D) Microstructural Characterization and Quantitative Analysis of Solidified Microstructures in Magnesium-Based Alloys

Ultra high-temperature deformation in a single crystal superalloy: Meso-scale process simulation and micro-mechanisms

Three-dimensional Ductile Fracture Analysis with a Hybrid Multiresolution Approach and Microtomography

MEMS-based in situ electron-microscopy investigation of rapid solidification and heat treatment on eutectic Al-Cu

Quantification of melt pool dynamics and microstructure during simulated additive manufacturing

In-situ investigation of damage mechanisms in duplex AlCoCrFeNi2.1 high entropy alloy

Dynamic evolution of microstructure morphology in thin-sample solidification: Deep learning assisted synchrotron X-ray radiography