Abstract:Polypropylene hollow fiber membrane (PPHFM) contactor, with aqueous solution absorbent such as sodium hydroxide (NaOH), monoethanolamine (MEA) and diethanolamine (DEA), was designed and used to separate and fix CO2 from CO2/N2 gas mixtures. The factors that influence the separation properties of CO2/N2 were investigated. It was found that the CO2 removal efficiency is the best by using MEA solution as absorbent. The overall mass transfer coefficient (K) increases with the increase of liquid flow, gas flow and the concentration of the absorbent; however, it decreases with the carbon dioxide concentration in the gas mixture and the temperature of the absorbent solution. Preliminary results showed that carbon dioxide can be fixed efficiently into sodium carbonate and/or sodium bicarbonate with NaOH as the absorbent in the membrane contactor. Pure carbon dioxide, on the other hand, can be produced when MEA or DEA was used as the absorbent. INTRODUCTION Membrane separation of gases has emerged into an important unit operations technique offering specific advantages over more conventional separation procedures (e.g. cryogenic distillation and adsorption). One can envisage that these technologies will also make great contribution to the growth of new research area, such as carbon dioxide capture from flue gas. However, even through there are a large number of potential applications for gas separation with polymer membranes, only relatively few of them have become applied in practice. The potential application of a polymer as a separation membrane depends upon the possible throughput and the purity of product. This means that both the permeability coefficient for the gas that is transported more rapidly and the selectivity should be as large as possible. However, it was found that simple structural modifications, which lead to increases in polymer permeability usually, cause losses in permselectivity and vice versa. This so-called ′′trade-off′′ relationship is well described in the literature. It is thus possible to find polymers that exhibit high selectivity and low permeability and vice versa, in addition to that combine low selectivity with low permeability. There do not appear to be any polymers that show the desired trend to large values for both permeability and selectivity. Therefore, new membrane materials and technologies should be exploited to accommodate new applications, such as the simultaneous separation and capture of carbon dioxide from flue gas. TECHNOLOGY Membrane contactors are devices that achieve gas/liquid or liquid/liquid mass transfer without dispersed one phase within another. As schematically represented in Figure 1, they are accomplished by passing the fluid on opposite side of a microporous membrane or a composite membrane (e.g. microporous membrane coated with PDMS rubber). The porous membrane acts as a non-selective barrier between both phases. Separation is determined by the reaction of one component in the gas mixture with the absorbent in the liquid. Figure 1. Schematic rep This approach offers a numb contactor for gas sorption, such m), no flooding and foaming p low energy consumption and eas composite membranes, the main turn, low energy consumption), with absorbent variation. A sim listed in Table 1. P

Simultaneous Separation of H2S and CO2 from Biogas by Gas–Liquid Membrane Contactor Using Single and Mixed Absorbents

ENHANCED SIMULTANEOUS SEPARATION OF H2S AND CO2 BY AN AMINO ACID SALT-PROMOTED POTASSIUM CARBONATE SOLUTION IN A HOLLOW FIBER MEMBRANE CONTACTOR

Experimental studies on simultaneous removal of CO2 and SO2 in a polypropylene hollow fiber membrane contactor

Selective Separation of H2S and CO2 from CH4 by Supported Ionic Liquid Membranes

VALORIZATION OF BIOGAS THROUGH SIMULTANEOUS CO2 AND H2S REMOVAL BY RENEWABLE AQUEOUS AMMONIA SOLUTION IN MEMBRANE CONTACTOR

Theoretical Study on CO2 Absorption from Biogas by Membrane Contactors: Effect of Operating Parameters

Selective Removal of H2S over CO2 in a Membrane Gas–liquid Microdisperison Microreactor

Absorbent screening using a hollow fiber membrane contactor for removing volatile methyl siloxanes from biogas

A Hybrid Method Combining Membrane Separation and Chemical Absorption for Flexible CH 4 Refinement and CO 2 Separation in Natural Gas

CO2/CH4 Separation Performance of SiO2/PES Composite Membrane Prepared by Gas Phase Hydrolysis and Grafting Coating in Gas-Liquid Membrane Contactor: A Comparative Study

Separation and Fixation of Carbon Dioxide Using Polymeric Membrane Contactor

Absorption of CO2 Form Natural Gas via Gas-liquid PVDF Hollow Fiber Membrane Contactor and Potassium Glycinate as Solvent

Removal of Carbon Dioxide from Pressurized Landfill Gas by Physical Absorbents Using a Hollow Fiber Membrane Contactor

Simultaneous absorption of H 2 S, MM and COS into a novel SRSG absorbent using a rotating packed bed

Development of cost-effective cellulose-based bilayer hybrid composite membranes for CO2 separation in biogas purification

Renewable CO 2 Absorbent for Carbon Capture and Biogas Upgrading by Membrane Contactor

Low Viscosity Superbase Protic Ionic Liquids for the Highly Efficient Simultaneous Removal of H2S and CO2 from CH4

Study on the Effectiveness of Ionic Liquid-Based Biphasic Amine Solvent in Removing H2S, NH3 and CO2 from Biogas and Its Influential Characteristics

Removal of CO2 from Simulated Flue Gas of Power Plants by Membrane-Based Gas Absorption Processes

Comprehensive experimental and theoretical insights into the performance of polysulfone hollow-fiber membrane modules in biogas purification process

Volatile Methyl Siloxane Separation from Biogas Using Hollow Fiber Membrane Contactor with Polyethylene Glycol Dimethyl Ether: A Numerical and Experimental Study