Abstract:The process formability of incremental sheet forming (ISF) is better than the conventional forming processes. Stretching, through-thickness-shear, bending-under-tension (BUT), and compressive forces are the proposed deformation mechanisms for improved formability; however, researchers have not corroborated (on consensus) the relative significance of any one among these. Similarly, researchers observed abrupt fractures (brittle fracture) and fractures preceded by necking (ductile fracture) for different case studies, which initiated a new debate and is still unanswered. Besides, researchers have extended the ISF to energy-assisted ISF to improve the process formability further for materials having a high strength-to-weight ratio. Three prominent energy-assisted ISF are (a) Electric-assisted ISF (E-ISF) works on the principle of lowering the yield stress by raising the temperature and has shown promise for Magnesium and Titanium alloy. (b) The ultrasonic vibration-assisted (UV-ISF) process works on the principle of acoustoplastic softening effect and thus far improved the room temperature material formability while reducing the forming forces. (c) Electromagnetic-assisted ISF (EM-ISF) is a non-contact, high-speed process that utilizes the pulsed magnetic field to apply inertial force, which improves formability by dislocation slips. The EM-ISF and UV-ISF have shown promise to counter the challenges during aluminum alloy forming; however, the work in this regard is still in the initial phase and has not explored its full potential. This study updates the potential research on the current status of the energy-assisted ISF. Different customized testing equipment is discussed that help understand the process mechanism. Microstructural changes in the material occur at normal ISF and with energy-assisted ISF are discussed in detail. Discussion and future work are presented based on the insight from various articles at the end.

On the Fracture Characterization in Double-Sided Incremental Forming of Ti6al4v Sheets at Elevated Temperatures

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Advanced FEM Insights into Pressure-Assisted Warm Single-Point Incremental Forming of Ti-6Al-4V Titanium Alloy Sheet Metal

A review on the deformation mechanism and formability enhancement strategies in incremental sheet forming

Crystal plasticity model of induction heating-assisted incremental sheet forming with recrystallisation simulation in cellular automata

In-situ investigation on the anisotropic behavior of the additively manufactured dual-phase Ti-6Al-4V alloy

Temperature-dependent Mechanical Properties and Fracture Behavior of Directionally Solidified Ti47Al2Cr2Nb Alloy

Investigating the microstructural evolution during deformation of laser additive manufactured Ti–6Al–4V at 400 °C using in-situ EBSD

Study on the Tensile and Shear Behaviors of Selective Laser Melting Manufactured Ti6Al4V

Experimental and Numerical Fracture Characterization of DP1180 Steel in Combined Simple Shear and Uniaxial Tension

Microstructural Influence on Fracture Toughness of IF Steel and DP Steel

A Generalized Stress State and Temperature Dependent Damage Indicator Framework for Ductile Failure Prediction in Heat-Assisted Forming Operations

Study on the Evolution of Damage Degradation at Different Temperatures and Strain Rates for Ti-6Al-4V Alloy

Investigation on the thermal deformation mechanisms and constitutive model of Ti-55511 titanium alloy

An investigation of ductile fracture behavior of Ti6Al4V alloy fabricated by selective laser melting

On Strain-Hardening Behavior and Ductility of Laser Powder Bed-Fused Ti6Al4V Alloy Heat-Treated above and below the β-Transus

Thermo-Mechanical Numerical Simulation of Friction Stir Rotation-Assisted Single Point Incremental Forming of Commercially Pure Titanium Sheets

Experimental and numerical investigations into the ductile fracture during the forming of flat-rolled 5083-O aluminum alloy sheet

Effect of Multidirectional Isothermal Forging on Microstructure and Mechanical Properties in Ti-6Al-4V Alloy

Non-monotonic plasticity and fracture in DP1000: Stress-state, strain-rate and temperature influence

Explicating tensile response of AA6061-T6 sheet post single point incremental forming: Two camera-DIC strain measurement and texture analysis