Abstract:Multi-stage microforming is increasingly used in manufacturing of the miniaturized parts with complex structures and geometries. Optimization design of this type of manufacturing process, however, is still challenging due to its unknown intrinsic nature of the process. In the multi-stage deformation and microforming, the size effect (SE), the strain path change (SPC), and the intragranularly misoriented grain boundary (IMGB) generated in previous forming stage, are the main factors governing the deformation behaviors of ultra-thin sheets. To gain thorough insights into their influences on deformation and elucidate the associated micro-scaled mechanisms, SS 316L ultra-thin sheets with the thickness of 0.1 mm and different mean grain sizes (d) were used for two-stage tensile tests under the conditions with distinct pre-strain & epsilon;pre and intersection angle & theta;SPC (the angle between the previous loading direction and subsequent one). Mechanical tests reveal that increasing & epsilon;pre and & theta;SPC reduces the yield stress and hardening rate in SPC tension, but this reduction gets smaller after increasing d. This is because more IMGBs with complex pattern are formed in relatively large grains, raising the permanent deformation resistance inside grains in subsequent tension. To model the IMGB-induced hardening, the SPC-induced softening, and the SE-induced concurrent facilitations to the hardening and softening, an enhanced crystal plasticity constitutive relation was established. The physical essence that IMGB obstructs dislocation movement, is used to model the IMGB-induced hardening based on the interactions between the main slip planes and IMGBs. The hardening facilitation caused by increasing grain size is implicitly incorporated in determining the saturated slip resistance. Modelling of the SPC-induced softening is based on the high Schmid factor grain fraction and its influences are governed by pre -strain and the defined SPC parameter. The softening facilitation caused by coarsening grains is modelled in establishing the initial slip resistance in SPC deformation. The proposed simulation procedure and constitutive relationship help with accurately predicting the mechanical response and microstructure evolution in micro-scaled SPC deformation, and also provide a basis for modelling and design of the multi-stage microforming of complex miniaturized parts.

Explicating tensile response of AA6061-T6 sheet post single point incremental forming: Two camera-DIC strain measurement and texture analysis

A study of local mechanical properties of 304L SS welded joints subjected to cyclic straining using depth-sensing instrumented indentation

Analytical and Experimental Investigations on Deformation Mechanism and Fracture Behavior in Single Point Incremental Forming

Investigations on the deformation mechanism of a novel three-sheet incremental forming

Experimental Investigations on Deformation Characteristics in Microstructure Level During Incremental Forming of AA5052 Sheet

Investigation of Pre-Aged Hardening Single-Point Incremental Forming Process and Mechanical Properties of AA6061 Aluminum Alloy

Investigation of Macro- and Grain-Scale Residual Stresses with an Emphasis on Spring-Back Behavior in Preheated Incrementally Formed AA 1050 H14 Components

Microstructural analysis of AA8079 alloy sheets formed by friction stir incremental forming

Crystal plasticity model of induction heating-assisted incremental sheet forming with recrystallisation simulation in cellular automata

Numerical and experimental studies for the effects of through-the-thickness shear on formability in single point incremental forming

Investigation of Material Deformation Mechanism in Double Side Incremental Sheet Forming

Increasing the Formability of CP-Ti During Incremental Sheet Forming with an Auxiliary Sheet

Investigations on the Forming Characteristics of a Novel Flexible Incremental Sheet Forming Method for Low-Ductility Metals at Room Temperature

Analysis of Thickness Distributions Calculated from Surface Strains Obtained through Digital Image Correlation for Incremental Sheet Forming

Crystal Plasticity-Based Analysis and Modelling of Grain Size and Strain Path Dependent Micro-Scaled Deformation Mechanisms of Ultra-Thin Sheet Metals

Mechanism Investigation for the Influence of Tool Rotation and Laser Surface Texturing (LST) on Formability in Single Point Incremental Forming

A review on the deformation mechanism and formability enhancement strategies in incremental sheet forming

Identification of forming performance parameters for 6016 aluminum alloy sheet under different strain paths via digital image correlation technology

Change in geometry size and thinning rate in single-point incremental forming process of TA1 sheet: evaluation method and finite element analysis

Numerical analysis of stress & strain and thickness variation in single point incremental forming of tailor welded steel blanks

Analytical Modeling of Fracture Strain and Experimental Validation in Incremental Sheet Forming