Abstract:The microstructures and mechanical properties of Inconel 718 (IN718) alloy fabricated by selective laser melting (SLM) are evaluated in as-built, direct aging (DA), and homogenization + aging (HA) conditions on considering the effect of applied loading direction. The results show that the microstructure of as-built and DA specimens consist of the intracrystalline fine degenerated dendritic structures (0.6-1 mu m in spacing) with a high density of dislocations (10(13)-10(14) m(-2)). Fine dendritic structures disappear after HA treatment, and the average geometrically necessary dislocation (GND) density decreases to 10(12) m(-2). A quantitative analysis of strengthening mechanisms is established by taking into consideration the grain boundary, solid solution, precipitation and dislocation strengthening. For the as-built and DA specimens, the contribution to the yield strength by dislocation strengthening is -85 MPa in vertical deposition and-170 MPa in horizontal deposition, respectively, and the Laves phases provide approximately 100-110 MPa. The contribution of precipitation strengthening to the strength increment in the DA and HA specimens is 590-600 and 830-850 MPa, respectively. The precipitation strengthening is mainly contributed by shearing mechanisms among which coherency strengthening plays dominant effect rather than order strengthening. For as-built, DA, and HA regimes, the specimens always exhibit higher strength along the horizontal direction than that along the vertical direction. The anisotropy of yield strength in the as-built and DA specimens is mainly attributed to the difference in dislocation density and effective grain size, and the anisotropy of yield strength in the HA specimens is mainly caused by the difference in effective grain size and Taylor factor.

Anisotropic Tensile Behavior of in Situ Precipitation Strengthened Inconel 718 Fabricated by Additive Manufacturing

Microstructural evolution and mechanical performances of selective laser melting Inconel 718 from low to high laser power

Strengthening Mechanisms in Selective Laser-Melted Inconel718 Superalloy

Mechanical properties and microstructure evolution of selective laser melting Inconel 718 along building direction and sectional dimension

Microstructures and Mechanical Behaviors of Additive Manufactured Inconel 625 alloys via Selective Laser Melting and Laser Engineered Net Shaping

On the Microstructure and Tensile Properties of Inconel 718 Alloy Fabricated by Selective Laser Melting and Conventional Casting

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Microstructure and Mechanical Properties of Inconel 718 Thin Walls Prepared by Laser Direct Energy Deposition and Selective Laser Melting

Microstructural Evolution and Corrosion Behaviors of Inconel 718 Alloy Produced by Selective Laser Melting Following Different Heat Treatments

Deformation Behavior of Selective Laser-Melted Inconel 718 Superalloy

High‐Temperature Mechanical Behavior Assessment based on a Developed Constitutive Model of Inconel 718 Fabricated by Selective Laser Melting

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Effect of Standard Heat Treatment on the Microstructure and Mechanical Properties of Selective Laser Melting Manufactured Inconel 718 Superalloy

Insight into Elongation and Strength Enhancement of Heat-Treated LPBF Ni-based Superalloy 718 Using In-Situ SEM-EBSD

Comparison of Microstructures and Mechanical Properties of Inconel 718 Alloy Processed by Selective Laser Melting and Casting

The Microstructure and Property Evolutions of Inconel718 Lattice Structure by Selective Laser Melting

Anisotropic Tensile Properties and In-Situ Deformation Behavior of Inconel 718 Alloy Fabricated by Laser Directed Energy Deposition

Assessment of mechanical properties and fatigue performance of a selective laser melted nickel-base superalloy Inconel 718

Microstructures and High-Temperature Mechanical Properties of Inconel 718 Superalloy Fabricated via Laser Powder Bed Fusion

Microstructural evolution and mechanical properties of Inconel 718 alloy manufactured by selective laser melting after solution and double aging treatments

Influence of Build Orientation on Microstructure, Mechanical and Corrosion Behavior of Inconel 718 Processed by Selective Laser Melting