Abstract:Single hat sectioned hybrid beams composed of aluminum and Carbon Fiber Reinforced Polymeric materials (CFRP), intended for structural applications in the automotive and aviation sectors, have been studied from the point of their energy absorption capabilities when submitted to transverse low-velocity impact loading. Carbon fiber-epoxy composite prepregs were placed on the inside of the single hat sectioned aluminum sheet and completely cured in the autoclave under the recommended curing cycle. The bonding process between the aluminum sheet and composite layers was achieved by using 3M VHB™ 4930 double-sided acrylic foam tape. Bonding the aluminum and composite layers through adhesive tape eliminates the requirement of surface preparation of the aluminum layer through chemical etching or mechanical abrasion and thereby the strength of the metallic layer is not reduced due to the formation micropores during the chemical etching process. Results are shown in terms of load-displacement and damage morphologies diagrams; characteristic trends are compared and discussed. It was observed that the presence of viscoelastic adhesive tape material restricts the rupture (visual cracks) failure of the outer aluminum layer, resulting in the only impact-induced indentation for all impact energies. Numerical simulations were also performed to characterize and predict the failure mechanism of such hybrid beams when subjected to impact loading. Numerical predictions showed good correlation with experimental results for all impact histories at low and medium impact energies but a showed slight discrepancy for highest impact energy and were not able to successfully capture the system response in the unloading region. Current modeling does not consider damage healing or recovery with unloading and it is difficult to account for such change in material state. This study provides the low-velocity impact characteristics and collapse behavior of the hybrid hat sectioned beams under tensile and shear forces developed by impact loading by providing insight to their primary damage mechanisms relative to the impact energies. It was found that the primary damage of the specimen's changes from impact-induced indentation, minimal fiber breakage to partial perforation accompanied by larger indentation depth as the impact energy is increased from 6 to 12 J.

Nonlinear Low-Velocity Impact on Damped and Matrix-Cracked Hybrid Laminated Beams Containing Carbon Nanotube Reinforced Composite Layers

Dynamic Behavior of CFRP-Strengthened Reinforced Concrete Beams Without Stirrups under Impact Loading

Analysis of the Dynamic Response in Blast-Loaded CFRP-Strengthened Metallic Beams

Low-velocity Impact Response of Agglomerated FG-CNTRC Beams with General Boundary Conditions Using Gram–Schmidt–Ritz Method

Nonlinear Fracture Analysis of Delamination Crack Jumps in Laminated Composites

Cracking Behavior of Cfrp Laminate-Strengthened Rc Beams with Premechanical and Postmechanical Environmental Damage

Experimental and Simulation Study on Failure of Thermoplastic Carbon Fiber Composite Laminates under Low-Velocity Impact

Geometric Non-Linear Analysis of Auxetic Hybrid Laminated Beams Containing CNT Reinforced Composite Materials

Finite Element Method of a Progressive Intralaminar and Interlaminar Damage Model for Woven Fibre Laminated Composites under Low Velocity Impact

Effects of geometric nonlinearities on the coupled dynamics of CNT strengthened composite beams with porosity, mass and geometric imperfections

Experimental and numerical response and failure of laterally impacted carbon/glass fibre-reinforced hybrid composite laminates

Low-velocity Impact-Induced Damage of Continuous Fiber-Reinforced Composite Laminates . Part I . an FEM Numerical Model

Numerical Investigation into Using Coarse Meshes to Predict Damage Behaviors of Laminated Composites Subjected to Low-Velocity Impact

Experimental and numerical investigations on the dynamic response of woven carbon fiber reinforced thick composite laminates under low-velocity impact

A Microcracking-Based Model for the Dynamic Failure of Carbon/carbon Composites

An Efficient Numerical Method to Analyze Low‐velocity Impact Response of Carbon Fiber Reinforced Thermoplastic Laminates

Static, buckling, and free vibration responses of functionally graded carbon nanotube-reinforced composite beams with elastic foundation in non-polynomial framework

Low-Velocity Impact Characteristics of Hybrid Aluminum/CFRP Single Hat Sectioned Beam Adhesively Bonded Using Adhesive Tape

Finite element analysis on impact response and damage mechanism of composite laminates under single and repeated low-velocity impact

Dynamic mode-I delamination in composite DCB under impact loads with attunable dynamic effect

Low velocity impact analysis of beams made of short carbon fiber/carbon nanotube-polymer composite: A hierarchical finite element approach