Abstract:Analytical pyrolysis was conducted to study a relative comparison of the hydrocarbon and greenhouse gas emissions of three foundry sand binders as follows: (a) conventional phenolic urethane resin, (b) biodiesel phenolic urethane resin, and (c) collagen-based binder. These binders are used in the metal casting industry for making cores that are used to create internal cavities within castings. In this study, the core samples were flash pyrolyzed in a Curie-point pyrolyzer at 920 degrees C with a heating rate of about 3000 degrees C/sec. This simulated some key features of the fast heating conditions that the core binders would experience at the metal-core interface when molten metal is poured into green sand molds. The core samples were also pyrolyzed in a thermogravimetric analyzer (TGA) from ambient temperature to 1000 degrees C with a heating rate of 30 degrees C/min, and this simulated key features of the slow heating conditions that the core binders would experience at distances that are further away from the metal-core interface during casting cooling. Hydrocarbon emissions from flash pyrolysis were analyzed with a gas chromatography-flame ionization detector, while hydrocarbon and greenhouse gas (CO and CO2) emissions from TGA pyrolysis were monitored with mass spectrometry. The prominent hazardous air pollutant emissions during pyrolysis of the three binders were phenol, cresols, benzene, and toluene for the conventional phenolic urethane resin and biodiesel resin, and they were benzene and toluene for the collagen-based binder. It was also found that volatile organic compound and polycyclic aromatic hydrocarbon emissions considerably decreased in order from conventional phenolic urethane resin to biodiesel resin to collagen-based binder. These results have shown some similarity with those for stack emission testing conducted at demonstration scale and/or full-scale foundries, and the similar trends in the two sets of results offered promise that bench-scale analytical pyrolysis techniques could be a useful screening tool for the foundries to compare the relative emissions of alternative core binders and to choose proper materials in order to comply with air-emission regulations.

Evolved Gas Analysis of PEP-SET Sand by TG and FTIR

Analysis on low-temperature polyethylene pyrolysis and gasification in different atmospheres

Hazardous Air Pollutant Formation from Pyrolysis of Typical Chinese Casting Materials.

Study on the Mechanisms of Hazardous Air Pollutant Emissions from Green Sand Casting

Characterization of hydrocarbon emissions from green sand foundry core binders by analytical pyrolysis

Characterization of Pyrolysis Products from a Biodiesel Phenolic Urethane Binder.

FTIR and GCMS analysis of epoxy resin decomposition products feeding the flame during UL 94 standard flammability test. Application to the understanding of the blowing-out effect in epoxy/polyhedral silsesquioxane formulations

[Application of Analytical Pyrolysis in Air Pollution Control for Green Sand Casting Industry].

Pyrolysis Kinetic Study and Reaction Mechanism of Epoxy Glass Fiber Reinforced Plastic by Thermogravimetric Analyzer (TG) and TG–FTIR (Fourier-Transform Infrared) Techniques

Thermogravimetric and Mass-Spectrometric Analyses of Combustion of Spent Potlining under N2/O2 and CO2/O2 Atmospheres

Kinetic analysis of resin binder for casting in combustion decomposition process

Insight into pyrolysis behavior of silicone-phenolic hybrid aerogel through thermal kinetic analysis and ReaxFF MD simulations

Preparation, flame retardancy, and thermal degradation of epoxy thermosets modified with phosphorous/nitrogen-containing glycidyl derivative

Evaluation of Volatile Hydrocarbon Emission Characteristics of Carbonaceous Additives in Green Sand Foundries.

Pyrolysis behavior of the nanoporous phenolic matrix and the resultant microstructure and property evolution in the composites

The Exhaust Gas Analysis of Dye Residue Pyrolysis by TG-FTIR

Insight into the Pyrolysis Behaviors of Petroleum-Driven Mesophase Pitch via ReaxFF Molecular Dynamics and In Situ TG-FTIR/MS

Pyrolysis characteristics and kinetics of waste photovoltaic module: A TG-MS-FTIR study

The Pyrolysis Behaviors of Blended Pellets of Pine Wood and Urea-Formaldehyde Resin

Pyrolysis characteristics, reaction mechanisms and gas emission of organic fireproof plugging materials by TG-FTIR-MS

TG-FTIR study of pyrolysis products evolving from dyestuff production waste