Abstract:Development of high-performance NO2 gas sensors with good sensitivity and long-term stability at high tem-peratures is expected for exhaust gas monitoring. The sensor performance mainly depends on sensing material. In this work, p-NiO/n-NiNb2O6 heterojunction material is successfully synthesized and an impedimetric NO2 sensor was assembled using the above material as sensing electrode (SE) and gadolinia-doped ceria (CGO) with a dense/ porous bilayer structure as a solid electrolyte. Introduction of SE to the CGO porous layer by screen printing followed by cold isostatic pressing treatment before calcination allows SE to successfully enter inside the porous layer and greatly increases the area of the three-phase boundary (TPB) and improves the long-term stability of the sensor. Using NiO/NiNb2O6 heterojunction SE can effectively improve the modulus (|Z|) response value (S|Z| = (|Z|air -|Z|gas)/|Z|air) of the sensor. Among the sensors, 90NiO/10NiNb2O6 (the mass ratio of NiO to Nb2O5 is 9:1) based NO2 sensor exhibits the best response performance and the highest sensitivity (0.34/ppm at 500 degrees C). The sensor also shows an excellent anti-interference property. Introduction of 300 ppm CO2, CH4, NO, CO, or H2 into 300 ppm NO2 makes response signal change below 3 % and 300 ppm NH3 only leads to signal reduction by 8.9 %, which is relatively low in a similar sensing system. The sensor response toward NO2 is slightly affected by O2 concentration change in 5-21 %. The superior performance of the sensor can be principally attributed to the heterojunction effect, which promotes the charge transfer and the adsorption capacity for NO2.

High-temperature NO2 sensor based on aluminum/indium co-doped lanthanum silicate oxyapatite electrolyte and cobalt-free perovskite oxide sensing electrode

High Performance Solid Electrolyte-Based NO2 Sensor Based on Co3V2O8 Derived from Metal-Organic Framework

An Amperometric NO2 Sensor Based on La10Si5NbO27.5 Electrolyte and Nano-Structured CuO Sensing Electrode.

Study of NO2 sensors based on La0.8Sr0.2Co0.2Fe0.8O3-δ/Ag biphasic composite sensing electrodes

Investigation on Impedencemetric-type NO_2 Sensor Based on La_(0.75)Sr_(0.25)Mn_(0.5)Co_(0.5)O_(3-δ) Sensing Electrode

Investigation on Impedencemetric-type NO2 Sensor Based on La0.75Sr0.25Mn0.5Co0.5O3-δ Sensing Electrode

Mixed potential type sensor using stabilized zirconia and La 0.75Sr0.25Cr0.5Mn0.5O3 sensing electrode for NO2 detection

An Amperometric Type NO2 Sensor Utilizing La0.7Sr0.3MnO3-δ-NiO Composite Sensing Electrode

A La10Si5NbO27.5 based electrochemical sensor using nano-structured NiO sensing electrode for detection of NO 2

Enhanced gas-sensing performance of SnO2/Nb2O5 hybrid nanowires

Effects of Ni Addition on the Response of La2cuo4 Sensing Electrode for No Sensor

Mixed Potential Type Sensor Using Stabilized Zirconia and La<sub>0.75</sub>Sr<sub>0.25</sub>Cr<sub>0.5</sub>Mn<sub>0.5</sub>O<sub>3</sub> Sensing Electrode for NO<sub>2</sub> Detection

Impedancemetric NO 2 sensor based on Pd doped perovskite oxide sensing electrode conjunction with phase angle response

Mixed-potential Type NO2 Sensor Prepared with CuCr2O4-CuO Composite Sensing Electrode

Chemical and Electronic Modulation via Atomic Layer Deposition of NiO on Porous In2O3 Films to Boost NO2 Detection

Potentiometric NO2 Sensors Based on Thin Stabilized Zirconia Electrolytes and Asymmetric (La0.8Sr0.2)0.95MnO3 Electrodes

In Situ Exsolution of PdO Nanoparticles from Non-Stoichiometric LaFePd0.05O3+δ Electrode for Impedancemetric NO2 Sensor

Impedimetric-type NO2 Sensor Based on the P-Nio/n-ninb2o6 Heterojunction Sensing Electrode

High-entropy oxide (FeCoNiCrMn)3O4 for room-temperature NO2 sensors

Amperometric type NO2 sensor based on La0.75Sr0.25Cr0.5Fe0.5O3-δ-Bi2O3 sensing electrode prepared by self-demixing

Impedancemetric-type NO2 Sensor Based on Non-Stoichiometric Perovskite Type Sensing Electrode Using Multiple Response Signals