Abstract:Cu2S, consisting of Earth-abundant and eco-friendly elements, is a promising candidate for thermoelectric energy conversion. The stoichiometric Cu2S has intrinsically low thermal conductivity together with meagre electrical conductivity. Herein, in order to improve the electrical properties, we develop a facile solvothermal method for synthesizing a series of Cu2–xS with tunable phase compositions. With reduction in the CuCl/Na2S molar ratio in the solution precursors from 2:1 to 1.75:1, the solvothermal products transform from single-phase Cu2S into Cu2S–Cu1.96S composites, which are preserved in the hot-pressed pellets. The decreased CuCl/Na2S molar ratio results in increased room-temperature Hall carrier concentration, leading to enhanced electrical conductivity. Specifically, the pellet corresponding to the 1.75:1 CuCl/Na2S precursor ratio obtains a power factor of 8.04 μW cm–1 K–2 at 815 K, which is ∼735% of the value obtained by stoichiometric Cu2S. Along with the moderate thermal conductivity, this sample achieves an enhanced zT value of 0.87 at 815 K, representing a ∼250% increase when compared to stoichiometric Cu2S. This study demonstrates an effective strategy in enhancing the thermoelectric performance of solution-synthesized Cu2S-based materials by phase tuning.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c13050.Extra XRD, SEM, TEM, EPMA, EDS, and WDS results on the synthesized samples, calculated weight fraction of Cu1.96S in the samples, Rietveld refinement results, thermoelectric property comparison, and zT values of the Cu2S–Cu1.96S-3 pellets in the first three cycles (PDF)This article has not yet been cited by other publications.

Facile rapid synthesis of a nanocrystalline Cu2Te multi-phase transition material and its thermoelectric performance

Facile Synthesis of Monodisperse Cu3SbSe4 Nanoparticles and Thermoelectric Performance of Cu3SbSe4 Nanoparticle-Based Materials

Systhesizing Snte Nanocrystals Leading to Thermoelectric Performance Enhancement Via an Ultra-Fast Microwave Hydrothermal Method

Multiple Nanostructures in High Performance Cu2S0.5Te0.5 Thermoelectric Materials

High Thermoelectric Figure of Merit Achieved in Cu2S1-xTex Alloys Synthesized by Mechanical Alloying and Spark Plasma Sintering

Enhanced Thermoelectricity in High-Temperature Β-Phase Copper(I) Selenides Embedded with Cu2Te Nanoclusters.

CsCu5S3: Promising Thermoelectric Material with Enhanced Phase Transition Temperature.

Phase Tuning for Enhancing the Thermoelectric Performance of Solution-Synthesized Cu 2– x S

One-step Rapid Synthesis of Cu2Se with Enhanced Thermoelectric Properties

Structurally nanocrystalline electrically monocrystalline Sb2Te3 with high thermoelectric performance

Multiscale architectures boosting thermoelectric performance of copper sulfide compound

Realizing high thermoelectric performance in Te nanocomposite through Sb2Te3 incorporation

Enhanced performance of thermoelectric nanocomposites based on Cu12Sb4S13 tetrahedrite

High thermoelectric properties of Cu2Te Ag2Te composite with Fe addition and non-stoichiometric Te

Optimal performance of Cu1.8S1−xTex thermoelectric materials fabricated via high-pressure process at room temperature

Ultralow Thermal Conductivity and Extraordinary Thermoelectric Performance Realized in Codoped Cu3SbSe4 by Plasma Spark Sintering

Optimized thermoelectric performance of N‐type Bi2Te2.7Se0.3 commercial materials by dispersing CuS nanoparticles

Ultra-fast fabrication of Bi2Te3 based thermoelectric materials by flash-sintering at room temperature combining with spark plasma sintering

Nanostructure Engineering and Performance Enhancement in Fe2O3-Dispersed Cu12Sb4S13 Thermoelectric Composites with Earth-Abundant Elements.

Excellent thermoelectric properties and stability realized in copper sulfides based composites via complex nanostructuring

High thermoelectric performance near the Mott–Ioffe–Regel limit in Cu S0.6Te0.4 meta-phases