Abstract:In-plane uniaxial tension of AZ31 magnesium alloy sheet with non-basal texture has been conducted in order to demonstrate the effects of loading direction on the microstructure evolution and mechanical properties at ambient temperature. Loading axes are chosen to be along five directions distributed between rolling direction (RD) and transverse direction (TD), allowing various activities in involved slip and twinning modes to take place. As for twinning modes, electron backscattered diffraction observations confirm that the contribution of \({{\{ 10\overline{1}1\} }}\) compression twinning is minimal to the plastic deformation of all deformed samples. By comparison, \({{\{ 10\overline{1}2\} }}\) extension twinning (ET) not only serves as an important carrier on sustaining and accommodating plastic strain but also contributes to the emergence of TD-component texture with the progression of plastic strain. In terms of slip modes, analysis on Schmid factor demonstrates that the increasing tilted angle between loading direction and RD of sheet is unfavorable to the activation of basal <a> slip, whereas it contributes to the activation of prismatic <a> slip. These observations consequently explain the increasing tendency of 0.2% proof yield stress. Moreover, the activations of basal <a> slip and \({{\{ 10\overline{1}2\} }}\) ET collectively contribute to the concentration of two tilted basal poles toward normal direction. With increasing angle between loading direction and RD, the activations of basal <a> slip and \({{\{ 10\overline{1}2\} }}\) ET are gradually weakened. This leads to a weakening tendency about concentration of two tilted basal poles, a generally increasing tendency about Lankford value (r-value) and a generally decreasing tendency about strain-hardening exponent (n-value).

The Mechanism for the High Dependence of the Hall-Petch Slope for Twinning/Slip on Texture in Mg Alloys

A quantitative study on mechanical behavior of Mg alloys with bimodal texture components

Solute atom mediated Hall-Petch relations for magnesium binary alloys

Evolution of deformation mechanisms and their orientation dependence in fine-grained Mg-3Gd during tension

On the strengthening and slip activity of Mg-3Al-1Zn alloy with pre-induced { 10 1 ̄ 2 } twins

Self-Consistent Crystal Plasticity Modeling of Slip-Twin Interactions in Mg Alloys

Understanding the mechanisms of texture evolution in an Mg-2Zn-1Ca alloy during cold rolling and annealing

Exploring the Hall-Petch relation and strengthening mechanism of bimodal-grained Mg–Al–Zn alloys

Effects of Deformation Mechanisms on Texture Evolution and Mechanical Response of the Mg-1Al-0.5Mn-0.3Gd Alloy Under Plane Tension

Texture weakening effect from { 10 1 ̅ 1 } twins induced static recrystallization in ambient extrusion AZ31 magnesium alloy

Texture Evolution and Their Effects on the Mechanical Properties of Duplex Mg–Li Alloy

Effect mechanism of texture orientation on mechanical properties and Hall-Petch relationship of CVCDE AZ31 magnesium alloy via crystal plastic finite element method (CPFEM)

Evolution of Deformation Substructure and MgxZnyCaz Metastable Phase in Fine-Grained Mg Alloys

The mechanism for an orientation dependence of grain boundary strengthening in pure titanium

Quantitative investigation on the {10–12} twinning-detwinning behavior and twinning transfer of an extruded Mg-2.8Y sheet during compression-tension loading via quasi-in-situ EBSD observation

Deformation mechanisms of basal slip, twinning and non-basal slips in Mg–Y alloy by micropillar compression

Tensile mechanical behavior and texture evolution of the weak texture Mg–1Al–0.5Mn–0.3Gd magnesium alloy

Dependence of Microstructure Evolution and Mechanical Properties on Loading Direction for AZ31 Magnesium Alloy Sheet with Non-basal Texture During In-Plane Uniaxial Tension

Quantitative Investigation on the Slip/Twinning Activity and Cracking Behavior During Low-Cycle Fatigue of an Extruded Mg-3Y Sheet

Hall-Petch relationship and deformation mechanism of pure Mg at room temperature

Achieving excellent ductility with increased Schmid Factor but decreased direct strain contribution of basal slip in an intergranular misorientation tailored magnesium alloy