Abstract:The High Luminosity Large Hadron Collider (HL-LHC [1]), an upgrade of the LHC, is set to become operational in 2029, aiming to achieve instantaneous luminosities 5–7.5 times larger than the nominal value of the LHC. However, unlocking the full physics potential at this much higher luminosity level necessitates a tenfold increase in the data bandwidth processed by ATLAS. This poses significant challenges to the design of the Trigger and Data Acquisition systems. To address these challenges, a baseline architecture has been chosen for the ATLAS Phase-II upgrade, relying on a single-level hardware trigger known as the Level-0 Trigger. This trigger has a maximum rate of 1 MHz and a latency of 10 μs. Central to this upgrade is the inclusion of a new subsystem — the Global Trigger [2]. This component performs complex algorithms, akin to those currently used in Phase-I high-level trigger software (such as Topoclustering), on full-granularity calorimeter data. The Global Trigger is divided into three sublayers: the Multiplexer Processor (MUX) layer, the Global Event Processor (GEP) layer, and the Global to Central Trigger Processor [3] interface (gCTPi). A full-function Global Common Module (GCM) hardware prototype has been designed to fulfill the requirements of all three sublayers of the Global Trigger, featuring different firmware loads. This GCM prototype, based on the ATCA [4] front board form factor, incorporates two of the latest AMD (Xilinx) Versal Premium devices VP1802 [5]. These devices boast double the density of the Virtex UltraScale+ FPGA VU13P used in the previous design [6] and include an integrated SoC with a completely new architecture. To handle high-speed I/Os, this GCM prototype employs twenty 12-channel 25.7 Gb/s FireFly [7] optical engines. The estimated maximum power consumption of this GCM prototype is 400 W, which falls within the cooling capabilities of the ATLAS ATCA shelf. To ensure power integrity, signal integrity, and thermal performance, extensive PCB simulations and thermal simulations have been done to guide the layout design of the GCM prototype. This paper provides an in-depth overview of the design process for this full-function GCM prototype hardware, with a particular focus on technology choices and simulation results.

Latency Study of the High Performance Time to Digital Converter for the ATLAS Muon Spectrometer Trigger Upgrade

A Readout Digitization System for the ATLAS Muon Spectrometer Phase-I Trpc Trigger Upgrade

Development of a Time-to-digital Converter ASIC for the Upgrade of the ATLAS Monitored Drift Tube Detector

Design and performance of a TDC ASIC for the upgrade of the ATLAS Monitored Drift Tube detector

Upgrade of the ATLAS Level-0 TGC Endcap Muon Trigger for HL-LHC

Design and Evaluation of the LAr Trigger Digitizer Board in the ATLAS Phase-I Upgrade

ATLAS hardware-based Endcap Muon Trigger for future upgrades

Design of a Time-to-Digital Converter ASIC and a mini-DAQ system for the Phase-2 upgrade of the ATLAS Monitored Drift Tube detector

A Low-Power Time-to-Digital Converter for the CMS Endcap Timing Layer (ETL) Upgrade

Performance of a front-end prototype ASIC for the ATLAS High Granularity Timing Detector

Upgrade of the ATLAS Muon Trigger for the SLHC

The CMS Trigger Upgrade for the HL-LHC

The Clock and Control System for the ATLAS Liquid Argon Calorimeter Phase-I Upgrade

A DAQ prototype for the ATLAS small-strip Thin Gap Chamber Phase-I trigger upgrade

A High-Density Time-to-Digital Converter Prototype Module for BES III End-Cap TOF Upgrade

Overview of the ATLAS High-Granularity Timing Detector: project status and results

The Phase-1 Upgrade of the ATLAS Level-1 Endcap Muon Trigger

System design and prototyping of the CMS Level-1 Trigger at the High-Luminosity LHC

A full-function Global Common Module prototype for ATLAS Phase-II upgrade

Performance of small-diameter muon drift tube chambers with new fast readout ASIC at high background rates

A firmware oriented trigger algorithm for CMS Drift Tubes in HL-LHC