Abstract:The High Luminosity Large Hadron Collider (HL-LHC [1]), an upgrade of the LHC, is set to become operational in 2029, aiming to achieve instantaneous luminosities 5–7.5 times larger than the nominal value of the LHC. However, unlocking the full physics potential at this much higher luminosity level necessitates a tenfold increase in the data bandwidth processed by ATLAS. This poses significant challenges to the design of the Trigger and Data Acquisition systems. To address these challenges, a baseline architecture has been chosen for the ATLAS Phase-II upgrade, relying on a single-level hardware trigger known as the Level-0 Trigger. This trigger has a maximum rate of 1 MHz and a latency of 10 μs. Central to this upgrade is the inclusion of a new subsystem — the Global Trigger [2]. This component performs complex algorithms, akin to those currently used in Phase-I high-level trigger software (such as Topoclustering), on full-granularity calorimeter data. The Global Trigger is divided into three sublayers: the Multiplexer Processor (MUX) layer, the Global Event Processor (GEP) layer, and the Global to Central Trigger Processor [3] interface (gCTPi). A full-function Global Common Module (GCM) hardware prototype has been designed to fulfill the requirements of all three sublayers of the Global Trigger, featuring different firmware loads. This GCM prototype, based on the ATCA [4] front board form factor, incorporates two of the latest AMD (Xilinx) Versal Premium devices VP1802 [5]. These devices boast double the density of the Virtex UltraScale+ FPGA VU13P used in the previous design [6] and include an integrated SoC with a completely new architecture. To handle high-speed I/Os, this GCM prototype employs twenty 12-channel 25.7 Gb/s FireFly [7] optical engines. The estimated maximum power consumption of this GCM prototype is 400 W, which falls within the cooling capabilities of the ATLAS ATCA shelf. To ensure power integrity, signal integrity, and thermal performance, extensive PCB simulations and thermal simulations have been done to guide the layout design of the GCM prototype. This paper provides an in-depth overview of the design process for this full-function GCM prototype hardware, with a particular focus on technology choices and simulation results.

A DAQ prototype for the ATLAS small-strip Thin Gap Chamber Phase-I trigger upgrade

The Study of Strip Readout Prototype for Atlas Phase-I Muon Trigger Upgrade

The Prototype Design of Gfex — a Component of the L1calo Trigger for the ATLAS Phase-I Upgrade

A Front-End Electronics Prototype Based on Gigabit Ethernet for the ATLAS Small-Strip Thin Gap Chamber

Design of a Time-to-Digital Converter ASIC and a mini-DAQ system for the Phase-2 upgrade of the ATLAS Monitored Drift Tube detector

An sTGC Prototype Readout System for ATLAS New-Small-Wheel Upgrade

A Readout Digitization System for the ATLAS Muon Spectrometer Phase-I Trpc Trigger Upgrade

A Cosmic Ray Readout System for Qualifications of Small-Strip Thin Gap Chambers of the ATLAS Muon Spectrometer Phase-I Upgrade

A full-function Global Common Module prototype for ATLAS Phase-II upgrade

Note: Development Of Stgc Strip Front-End Readout Prototype For Atlas New Small Wheel Upgrade

Application of ATCA in trigger and DAQ system for experimental physics

Scanning Test System Prototype of p/sFEB for the ATLAS Phase-I sTGC Trigger Upgrade

The Development of the Front-End Boards for the Small-Strip Thin Gap Chambers Detector System of the ATLAS Muon New Small Wheel Upgrade

A Scanning Test System of P/sfeb Based on FPGA XADC for the ATLAS Phase-I Stgc Upgrade

Development of a Time-to-digital Converter ASIC for the Upgrade of the ATLAS Monitored Drift Tube Detector

Latency Study of the High Performance Time to Digital Converter for the ATLAS Muon Spectrometer Trigger Upgrade

Performance of Pad Front-End Board for Small-Strip Thin Gap Chamber with Cosmic Ray Muons

High Speed Ethernet Application for the Trigger Electronics of the New Small Wheel

Design and Evaluation of the LAr Trigger Digitizer Board in the ATLAS Phase-I Upgrade

The Improved Design of Multi-channel Thin Gap Chamber Simulation Signal Source for the ATLAS Detector Upgrade

Design and performance of a TDC ASIC for the upgrade of the ATLAS Monitored Drift Tube detector