Abstract:Powder metallurgy is an effective method to produce Cu-Al-based alloys for automotive and aerospace engineering components. The finer grain size, low cost, and low-temperature synthesis make this process more suitable than the other conventional production method such as melting and casting. The addition of Ni (austenite stabilizer) into the Cu increases the stability of Cu and refines the grain size. Again, the addition of Ni into the Cu-Al alloy increases the strength and hardness. In the present work, Cu-12Al alloys are developed by varying the wt.% of Ni content from 0 to 8 using powder metallurgy process through mechanical alloying method. Mechanical alloyed powder mixture is compacted by applying a load of 5 tons and sintered at 850 °C for 1 h under nitrogen atmosphere. It is found that α-Cu, γ2-Cu9Al4, and NiAl phases are presented in the Cu-12Al-Ni alloy which influences the properties of the alloy. The theoretical, sintered, and relative density values are decreased with increasing the wt.% of Ni content. However, the Vickers hardness of the alloy is improved by increasing the wt.% of Ni content up to 4 wt.% and then reduced for 8 wt.% of Ni content due to the coarsening and network-type structure of the NiAl phase. A higher amount of wear loss or wear rate is observed for the Cu-12Al and Cu-12Al-2Ni alloy than the Cu-12Al-4Ni and Cu-12Al-8Ni alloy. The presence of oxygen peaks in the EDS analysis revealed that an oxidative type of wear is occurred for the Cu-12Al alloy samples with varying the wt.% of Ni content. The electrochemical corrosion analysis revealed that the rate of corrosion is higher for Cu-12Al alloy without Ni. However, the rate of corrosion is reduced by increasing the wt.% of Ni content from 2 to 8.

Microstructure and Properties of Dilute Cu-Nb Alloy Prepared by Mechanical Alloying

Investigation of a Hot-Pressed Nb–Ti–Al Alloy: Mechanical Alloying, Microstructure and Mechanical Property

Eff ects of Diff erent Mechanical Alloying Parameters on Microstructure of High Temperature Nanocrystalline Cu-Ta Alloys

Preparation of Nb 3 Al Superconductor by Powder Metallurgy and Effect of Mechanical Alloying on the Phase Formation

Microstructure and mechanical properties of a Cu-Fe-Nb alloy with a high product of the strength times the elongation

Microstructure and Mechanical Properties of Cu–12Al–xNi Alloy Prepared Using Powder Metallurgy

Microstructure and properties of a novel ultra-high strength, high elasticity and high plasticity Cu–20Ni–20Mn-0.3Nb-0.3Cr-0.1Zr alloy

Study on Mechanical Properties and Microstructure of Cu20Fe80 Alloy Using the Mechanical Alloying

Microstructural evolution and mechanical properties of novel nanoparticles strengthened CoCrFeNi based high entropy alloy

Microstructure, Mechanical, and Tribological Relationship in Cu-12Al-Ni Alloy with Respect to the Variation of Ni Content

Micro-alloying effects of Ni on the microstructure and mechanical properties of an Al-Zn-Mg-Cu-Sc-Zr alloy

Study on Microstructure and Properties of Cu-Zr Alloy Prepared by Mechanical Alloying

Microstructure and Properties of High Strength and High Conductivity Cu-0.4Mg Alloy Processed by Upward Continuous Casting and Multi-pass Drawing

Effect of Nb content on mechanical reinforcement of the Cu-10Fe composites

Microstructure evolution and mechanical properties of CoCrFeNiAl0.3 high entropy alloy produced by ball milling in combination with thermomechanical consolidation

Effect of Microalloying Rare-Earth Nd on Microstructure Evolution and Mechanical Property of Cu Alloy

The Effect of a Small Addition of Nickel on the Sintering, Sintered Microstructure, and Mechanical Properties of Ti–45Al–5Nb–0.2C–0.2B Alloy

Microstructural evolution in Cu–Nb processed via friction consolidation

Tuning Microstructures and Tensile Properties of the CoNiV Medium Entropy Alloy by Minor Alloying

Microstructural Characterization of AlCrCuFeMnNi Complex Concentrated Alloy Prepared by Pressureless Sintering

Effect of Nb content on the stacking fault energy, microstructure and mechanical properties of Fe-25Mn-9Al-8Ni-1C alloy