Abstract:Tungsten carbide (WC), celebrated for its exceptional strength, hardness, and chemical inertness, serves as an exemplary reinforcement for copper (Cu) matrix composite (CMC) coatings, significantly enhancing their wear and corrosion resistance. However, the inherent poor wettability and interfacial bonding between WC and Cu during the cold spray additive manufacturing process pose challenges to further performance improvement of these coatings. This study investigates cold-sprayed CMC coatings reinforced with WC particles, both with and without an electroless plated cobalt (Co) shell (Co@WC; at 10 wt.% and 20 wt.%), focusing on their microstructure, mechanical properties, tribological behavior, and electrochemical corrosion resistance. The findings indicate a reduction in CMC coatings` porosity and mean free path (MFP) of reinforcement particles with increasing reinforcement content. Despite slight Co shell damage during deposition, ceramic retention is notably enhanced, reaching up to 149.3%. The microhardness and wear resistance of CMC coating are improved with decreased MFP and increased ceramic content. Compared to the Cu coating, the microhardness of CMC coatings escalates by up to 32.9% (151.8HV0.1), and the specific wear rate is dramatically reduced by up to 84.2%. The Co shell effectively prevents the detachment of Co@WC particles, thereby enhancing the bending and wear resistance. Electrochemical corrosion tests, encompassing open circuit potential (EOCP), polarization curve, and electrochemical impedance spectroscopy (EIS), indicate that lower porosity, high ceramic content and the Co shell substantially boost the corrosion resistance of the CMC coating. Specifically, the coating with 20 wt.% Co@WC (Cu20(Co@WC)) demonstrates superior corrosion resistance compared to the Cu coating, hinting at the potential for further enhancement with increased ceramic content.

Influence of Cu Content on the Structure, Mechanical and Tribological Properties of W2n-Cu Films

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Microstructure and Tribological Behavior of Cr-Cu-N Coatings Deposited by Ion Beam Assisted Magnetron Sputtering

Influence of Cu Content Variation on the Tribological Properties of Ni60CuMo with Sandwich-Structured Composite Coatings by Laser Cladding

Influence of Cu content on mechanical and tribological properties of Al–7Si–Cu alloy

Influence of Cu Content on the Microstructure and Mechanical Properties of Cr-Cu-N Coatings

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Effect of Cu content on high-temperature tribological properties and oxidation behavior of Al-Ti-V-Cu-N coatings deposited by HIPIMS

Influence of copper on the compositions, microstructure and room and elevated temperature tribological properties of the molybdenum nitride film

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Effect of Cu Addition on the Tribological Properties and Oxidation Behavior of Nanomultilayered AlTiN/Cu Coatings

Effect of Cu-doping on tribological properties of laser-cladded FeCoCrNiCu x high-entropy alloy coatings

Effect of Cu content on the microstructure and properties of sintered Fe-0.8C-xCu antifriction materials

Hard Nanocomposite Ti–Cu–N Films Prepared by D.c. Reactive Magnetron Co-Sputtering

The Effect of Copper Content on the Mechanical and Tribological Properties of Hypo-, Hyper- and Eutectoid Ti-Cu Alloys

Effect of Cu content on the wear resistant behavior of arc-sprayed laminated-structured Cu–TiN/TiO 2 composite coating

Current-carrying Tribological Behavior and Wear Mechanism of CuW Composites with Different W Content

Microstructure evolution and anti-wear mechanism of Cu film fabricated by magnetron sputtering deposition

Dry sliding tribological properties of Cu-WS 2 self-lubricating composites at 25–500 °C

Friction and Wear Properties of Wide-Velocity Range High-Energy Plasma Sprayed CuSn-NiCr Solid Self-Lubricating Coatings under Heavy Load

High hardness and wear resistance of W-Cu composites achieved by elemental dissolution and interpenetrating nanostructure.