Abstract:Polypropylene microporous membranes were prepared by melt-extrusion and cold-stretching (MSCS) method. The structure changes of microporous membrane during cold stretching, heat setting and hot stretching were studied in suit to reduce the effect of other factors on cold-stretching samples, such as natural retraction induced by cold stretch and the need of cool detection after heat setting. The influences of cold-stretching ratio on micro-lamellae and micropore structure of polypropylene microporous membranes were investigated by in situ small angle X-ray scattering (SAXS), scanning electron microscope (SEM) and differential scanning calorimeter (DSC). The results show that different cold-stretching ratios lead to the different hole formation mechanism. Long-period SAXS signals of the meridian direction at the cold-stretching ratio 15% indicate a slight change of macroscopic strain. Thus the corresponding pore formation mechanism is that cold stretching induces micro defects while hot stretching transforms them into micropores. At the cold stretching ratio 30%, small lamellae transform into unstable bridges and part of the bridges break after heat setting. Besides, noticeable signals of streak emerge in the vertical direction. When the cold-stretching ratio is increased to 40%, signals in stretching direction demonstrate that the growth rate of actual lamellar long period is lower than that of macroscopic strain. This phenomenon can be attributed to that partial skeleton lamellae are destroyed by stretching and transformed into bridging crystal fibers. Macro statistics and micro calculations show that the larger the stretching radio, the shorter the length of bridges and the smaller the aperture. Thus the S-30 is the most appropriate cold-stretching radio to prepare microporous membranes.

Strain and Temperature Dependence of Deformation Mechanism of Lamellar Stacks in Hdpe and Its Guidance on Microporous Membrane Preparation

Structure formation and characterization of PVDF hollow fiber membranes by melt-spinning and stretching method

Preparation and Structural Control of Polyethylene Hollow Fiber Membranes

Mechanical Energy and Thermal Effect Controlled Micropore Nucleation and Growth Mechanism in Oriented High Density Polyethylene

Stabilization Mechanism of Micropore in High-Density Polyethylene: A Comparison Between Thermal and Mechanical Pathways

Effect of Hot Stretching on the Structure of Polypropylene Microporous Membranes with in Situ Small Angle X-Ray Scattering

In situ Small Angle X-ray Scattering Study on the Pore Formation Mechanism of Polypropylene Microporous Membranes Prepared by the Melt-stretching Method

Structural Evolution of Hard-Elastic Polyethylene Cast Film in Temperature-Strain Space: an In-Situ SAXS and WAXS Study

Effect of stretching on structure and properties of polyethylene hollow fiber membranes made by melt-spinning and stretching process

Influence of Annealing Temperature on the Lamellar and Connecting Bridge Structure of Stretched Polypropylene Microporous Membrane

Influence of cocrystallization behavior on structure and properties of HDPE/LLDPE microporous membrane

Preparation of Highly Oriented Polyethylene Precursor Film with Fibril and Its Influence on Microporous Membrane Formation

Effects of Annealing Stress Field on the Structure and Properties of Polypropylene Hollow Fiber Membranes Made by Stretching

Fabrication of Microporous Membranes from Melt Extruded Polypropylene Precursor Films Via Stretching: Effect of Annealing

Effects of Room Temperature Stretching and Annealing on the Crystallization Behavior and Performance of Polyvinylidene Fluoride Hollow Fiber Membranes

The Effect of Stretching on UHWMPE Microporous Film by Thermally Induced Phase Separation Method

Structure and Properties of Biaxial Stretched Submicron Thin UHMWPE Membranes

Biaxial stretch-induced structural evolution of polyethylene gel films: Crystal melting recrystallization and tilting

Influence of annealing time on the structure and properties of high-density polyethylene microporous membrane

Evolution of the cavity structure of HDPE/UHMWPE blends during cold stretching

Effects of Cooling Ways on the Structure of Polypropylene Hollow Fiber Membranes Prepared by Stretching