Abstract:Bismuth telluride (Bi2Te3)-based alloys are widely used for thermoelectric cooling and power generation at low temperatures, and they are the only commercially available materials for thermoelectric applications below 500 K. The rhombohedral unit cell with a large c/a lattice constant ratio consisting of - Te-Bi-Te-Bi-Te- stacked layers inevitably brings about a large anisotropy in transport properties, which is why texturing is very important in polycrystalline Bi2Te3</sub alloys for maximum performance. In this report, p and n-type polycrystalline Bi2Te3</sub alloys were synthesized and hot-deformed to investigate the effects of texturing on thermoelectric properties. Hot deformation (HD) induces the strong alignment of (001) orientations along the compression direction, and a remarkable increase in the orientation factor F of (001) orientations is observed after HD in both p and n-type materials. All of the hot-deformed polycrystalline samples showed increased electrical conductivity (σ), power factor (PF), and thermal conductivity (k) in the in-plane (IP) direction, and vice versa in the out-of-plane (OOP) direction, which makes the IP direction of the hot-deformed bodies more favorable for module fabrication in terms of power factor, for both p and n-type Bi2Te3</sub-based alloys. However, due to the different degree of anisotropy of k and σ, the figures of merit (zT) were maximized in the OOP direction in the p-type materials after HD, whereas the zTs of the n-type materials were higher in the IP direction. This occurs because the anisotropy factor of electron conduction is higher than that of hole conduction, which more than offsets the advantage of the smaller k in the c-direction of n-type Bi2Te3</sub. The maximum zT of 1.33 (OOP) and 0.90 (IP) were obtained after HD from the p and n-type Bi2Te3 alloys, respectively, which were 9.3% and 18.4% higher than those of as-sintered materials.

The Effect of Texture Degree on the Anisotropic Thermoelectric Properties of (bi,sb)(2)(te,se)(3) Based Solid Solutions

The Texture Related Anisotropy of Thermoelectric Properties in Bismuth Telluride Based Polycrystalline Alloys

Analysis of Thermoelectric Properties of Hot-deformed Bismuth Telluride Sintered Materials

Mid-temperature Thermoelectric Performance of Zone-Melted Sb2(Te,Se)3 Alloys Near Phase Transition Boundary

The Anisotropic High Thermoelectric Performance in (BixSb1-x)2Te3

Anisotropic Thermoelectric Properties of N-Type Te-Free (bi, Sb)2Se3 with Orthorhombic Structure

Anisotropic Effects on the Thermoelectric Properties of Highly Oriented Electrodeposited Bi2Te3 Films

Anisotropic thermoelectric transport properties of Bi0.5Sb1.5Te2.96+x zone melted ingots

Enhancing thermoelectric performance of SrFBiS2−Se via band engineering and structural texturing

Study On Anisotropy Of N-Type Mg3sb2-Based Thermoelectric Materials

Thermoelectric Performance Enhancement in N -Type Bi 2 (tese) 3 Alloys Owing to Nanoscale Inhomogeneity Combined with a Spark Plasma-Textured Microstructure

Enhancement in thermoelectric performance of bismuth telluride based alloys by multi-scale microstructural effects

Isotropic Thermoelectric Performance of Layer-Structured n-Type Bi 2 Te 2.7 Se 0.3 by Cu Doping

The Thermoelectric Properties of n-Type Bismuth Telluride: Bismuth Selenide Alloys Bi2Te3- x Se x

Isovalent co-alloying contributes to considerable improvement in thermoelectric performance of BiSe bulks with weak anisotropy

Preferential Orientation and Thermoelectric Properties of P-Type Bi0.4Sb1.6Te3 System Alloys by Mechanical Alloying and Equal Channel Angular Extrusion

The Effect of Heat Treatment on Electrodeposited Bi2te3 Thin Films for Thermoelectric Applications

Enhancing room-temperature thermoelectric performance of n-type Bi2Te3-based alloys via sulfur alloying

Enhanced thermoelectric properties of layered anisotropic PbBi2Te4 through the suppression of bipolar diffusion effect via Se alloying

Enhanced Thermoelectric Properties of N-Type Direction Solidified Bi2Te2.7Se0.3 Alloys by Manipulating Its Liquid State

Tuning band structure and texture for improved thermoelectric performance in BiSe