Abstract:A thick-walled SUS316 saddle tube-pipe welded joint is used in nuclear power equipment. A very long computing time and huge memory space are needed to simulate welding residual stress when the thermo-elastic-plastic finite element method is used because of the complex shapes, large sizes, and many weld passes of this joint. To solve the computational problem, two efficient and accurate computational approaches were proposed based on MSC. Marc finite element software platform. In the first computational approach, the finite element model of the SUS316 saddle tube-pipe welded joint was established with the same dimensions as the actual joint. Two heat sources were used to balance the computing time and calculation precision. The moving heat-source model was used to simulate the heat input for the backing and cover passes. In contrast, the instantaneous heat-source model was employed to consider the heat input for the other passes. Considering the geometric symmetry, a quarter model was developed in the second computational approach, and the instantaneous heat-source model was used to model the heat input for all passes. In the material model, both work hardening isotropic rule and annealing effect were considered because SUS316 is sensitive to work hardening. The simulation results of the thermal cycle during the welding process and residual stress distribution in and near the fusion zone were compared using the measured data. The results of thermal cycles and the residual stress distributions obtained using two computational approaches matched the experimental measurements. When the first computational approach was used, not only the residual stress distribution in the whole welded joints could be obtained, but also the features of residual stress distribution near the weld start-end location were able to capture. The second computational approach could predict the magnitude and distribution of residual stress in the stable range of the joint and could save computing time and huge memory space. Thus, the second computational approach is useful for practical engineering applications.

Weld Residual Stress in Tube to Tube Sheet Joints of a Heat Exchanger by Experimental and Finite Element Simulation

Using X-Ray Diffraction and Finite Element Method to Analyze Residual Stress of Tube-to-Tubesheet Welded Joints in a Shell and Tube Heat Exchanger

Numerical Simulation of Welding Residual Stress of Tube-to-tubesheet Joint in Heat Exchangers

Generation of Compressive Residual Stress at the Root of Tube-to-tubesheet Welded Joints in a Heat Exchanger

Effect of Tube Arrangement on the Welding of the Tube-to-Tubesheet Joint of Shell-and-Tube Heat Exchangers Using the Finite Element Method

Determination of Repair Weld Residual Stress in a Tube to Tube-Sheet Joint by Neutron Diffraction and the Finite Element Method

Finite Element Analyses of Residual Stresses in Typical Welded Joints Used in Nuclear Power Plants and Comparisons with Experiments

Control of Welding Residual Stress and Deformation of the Butt Welded Ultrathick Tube-Sheet: Effect of Applied Load

Simulation on 3D Residual Stresses Field of Welding between Tubesheet and Tube in Reactor by FEM

Prediction of Residual Stress Distributions in Welded Sections of P92 Pipes with Small Diameter and Thick Wall Based on 3D Finite Element Simulation

Finite Element Simulation on Residual Stress and Deformation for Welding Joint of 20mnmonb Super-Thick Tube Sheet of Ethylene Oxide Reactor

A Study of the Residual Stress and Deformation in the Welding Between Half-Pipe Jacket and Shell

Residual stresses evolution during strip clad welding, post welding heat treatment and repair welding for a large pressure vessel

Numerical Simulation Analysis of Residual Stress in Welded Hollow Spherical Joint with Circular Steel Tubes

Numerical Simulation and Development of Efficient Calculation Method for Residual Stress of SUS316 Saddle Tube-Pipe Joint

Residual Stress Distribution in A Dissimilar Weld Joint by Experimental and Simulation Study

Evolution of welding residual stresses during cyclic tests in welded tubular joints

Influence of Deposition Sequence and Thickness of Tube on Welding Residual Stress and Deformation in Dissimilar Steel Tube-block Welded Joint

Combined Effect of Tungsten Inert Gas Welding and Roller Expansion Processes on Mechanical and Metallurgical Characteristics of Heat Exchanger Tube-To-Tubesheet Joints

Numerical Simulation Of Temperature Field And Residual Stress In Multi-Pass Welds In 2.25cr-1mo-0.25v Steel Plate And Comparison With Experimental Measurements

Prediction of Residual Stresses in a Dissimilar Metal Welded Pipe with Considering Cladding, Buttering and Post Weld Heat Treatment