Abstract:To extend the safety service life of aviation TC4 alloy, the composite coatings of TC4 + Ni-MoS2 + WC + xY2O3 (x = 0, 1, 2, 3, 4 wt.%) were prepared on TC4 by coaxial powder feeding laser cladding technology. The results showed that all the coatings had the same generated phases which mainly consisted of TiC, Ti2Ni, Ti2S, matrix β-Ti, and unfused residual WC. Y2O3 formed co-dependent growth relationships with TiC, Ti2S, and Ti2Ni. Meanwhile, TiC-Ti2S, TiC-Ti2Ni, and Ti2S-Ti2Ni coherent composite structure phases were effectively synthesized in all the coatings. With the increase in the Y2O3 content, the exposed area of the matrix increased and other phases refined progressively. When the Y2O3 content in the coatings were 3 and 4 wt.%, the degree of phase refinement in the coatings was consistent and the phases grew along grain boundaries, but microstructure segregated in the 4 wt.% Y2O3 coating. The microhardness of all the coatings was higher than that of TC4 and decreased with the increase in the Y2O3 content. Higher friction coefficients and lower wear rates both appeared in all the coatings than in the substrate, and they presented a trend of decreased first and then increased with the addition of Y2O3, in which the 3 wt.% Y2O3 coating had the lowest friction coefficient and optimal wear resistance. The research found that the Y2O3 could not change the types of phases in the coatings and could serve as a heterogeneous nucleation center for the refinement of the TiC-Ti2S-Ti2Ni coherent structure phase. Meanwhile, except for the matrix phase, Y2O3 could attract other phases to pinning on the grain boundaries of the coatings. The content of Y2O3 was negatively correlated with the hardness and wear resistance of the coating and it had the optimal tribological properties with the moderate amount of Y2O3. The wear mechanism of all coatings was abrasive wear.

Effects of Y 2 O 3 /Y on Si-B Co-Deposition Coating Prepared Through HAPC Method on Pure Molybdenum

Formation and Oxidation Behavior of Mo-Si-B Composite Coatings with B-rich Interlayer Prepared by Slurry Sintering Method

Microstructure and oxidation behavior of SiOC coatings on C/C composites co-deposited with HMDS and TEOS by using CVD process

Influences of MCrAlY Coatings and TBCs on Oxidation Behavior of a Ni-Based Single Crystal Superalloy

Structure and Oxidation Resistance of Mo-Y-Zr-Si-B Coatings Deposited by DCMS and HIPIMS Methods Using Mosaic Targets

Microstructure and properties of Mo-Si-B-Y 2 O 3 composite coating on nickel-based alloy by laser cladding

Effect of Yb2O3 addition on oxidation/ablation behaviors of ZrB2-MoSi2 composite coating under different environment

Effect of the Y2O3 amount on the oxidation behavior of ZrB2-SiC-based coatings for carbon/carbon composites

Coating of Y2O3 additive on Al2O3 powder and its effect on the wetting behaviour in the system Al2O3p/Al

Effects of Y2O3 Content on the Microstructure and Tribological Properties of WC-Reinforced Ti-Based Coatings on TC4 Surfaces

Effect of yttrium on the oxidation resistance and areaspecific resistance of MnCo2O4 coating

Oxidation behaviors and mechanisms of Yb2O3-doped silicon coatings fabricated by vacuum plasma spray

Thermal shock behavior and oxidation resistance of novel SiC nanowires+Si/Yb2Si2O7-Si/Yb2Si2O7 environmental barrier coatings

Oxidation resistance and thermal shock behavior of tri-layer Si/Si–Yb2SiO5/Yb2SiO5–SiC environmental barrier coatings at 1300 °C

Evolution behavior of rare-earth yttria modified silicide oxidation-resistant coating at 1700 oC

Structure and High-Temperature Oxidation Performance of Si-Co Diffusion Coatings Prepared on a TiAl-Nb Alloy

Effect of Reaction Temperature on the Molten Salt Electrodeposition of Silicide Coating on Molybdenum Substrate and its Oxidation Behavior

Effects of the Deposition Mode and Heat Treatment on the Microstructure and Wettability of Y2O3 Coatings Prepared by Reactive Magnetron Sputtering

Effect of Co distribution on the oxidation behavior of aluminide coatings in Mo-rich Ni-based single-crystal superalloy

The effect of Si content on the structure and tribological performance of MoS2/Si coatings

Preparation and enhanced oxidation behavior of microalloyed Mo5SiB2 alloy at 1300 °C