Abstract:Due to the rapid heating-cooling process and unstable keyhole, pore defects are easily formed during the high energy beam-powder additive manufacturing (AM) process, posing great challenges to the high-performance manufacturing of aerospace components. Using an arc with lower energy density as a heat source can effectively avoid these defects, but its matching raw materials are limited to wire. In this paper, a novel magnetic field assisted powder arc additive manufacturing (MFA-PAAM) method has been proposed, which combines arc heat source and powder raw material to achieve dense metal parts. A transverse magnetic field (TMF) was introduced to solve the powder spattering problem which impacts the stability of the PAAM process, by regulating the direction of the arc plasma flow and the arc pressure. The unique melting behavior of the powder under arc heating was captured by a high-speed camera, which can be summarized into two steps: balling and adsorption by the molten pool. And the well-formed and fully dense Ti60 high-temperature titanium alloy wall components were successfully manufactured using the self-developed equipment. The microstructure of the thin-wall component is dominated by basket-weave distributed α laths and few β sheets remaining at their boundaries. A layered periodic distribution along the building direction was observed, which is mainly distinguished from the content and morphology of the β phase. The average ultimate tensile strength (UTS) and elongation to failure in the travelling direction are 1003.2 MPa and 15.1%, while the average UTS and elongation along the building direction are 1009.3 MPa and 16.6%, respectively. The fracture morphologies in both directions are characterized by ductile fracture. The MFA-PAAM technique shows great potential for fabricating materials that are difficult to be drawn into wires with high efficiency and performance.

A Novel Method for Production of Spherical Ti-6al-4v Powder for Additive Manufacturing

A Method for the Preparation of Spherical Titanium Powder for Additive Manufacturing

Cost-effective Preparation of High-Purity Spherical Ti-6Al-4V Powder for Additive Manufacturing Via Hydrogen Decrepitation and Laser Spheroidization

Preparation of Spherical Porous and Spherical Ti6Al4V Powder by Copper-Assisted Spheroidization Method

Preparation of Ti6Al4V Powder with High Yield of Fine Particle by Crucible-less Gas Atomization Technology

Cost-affordable Ti-6Al-4V for Additive Manufacturing: Powder Modification, Compositional Modulation and Laser In-Situ Alloying

A novel direct reduction and alloying process for making additive manufacturing of titanium alloys greener

Production of Spherical TiAl Alloy Powder by Copper-Assisted Spheroidization

Production of spherical titanium alloy powders used in additive manufacturing from titanium scrap

Ultra-low cost Ti powder for selective laser melting additive manufacturing and superior mechanical properties associated

Additive manufacturing of a high-performance aluminum alloy from cold mechanically derived non-spherical powder

A Novel Approach of Fabricating Monodispersed Spherical MoSiBTiC Particles for Additive Manufacturing.

A Novel Method to 3D-Print Fine-Grained AlSi10Mg Alloy with Isotropic Properties Via Inoculation with LaB6 Nanoparticles

Plasma spheroidisation and characterisation of commercial titanium grade 5 powder for use in metal additive manufacturing

A novel magnetic field assisted powder arc additive manufacturing for Ti60 titanium alloy: Method, microstructure and mechanical properties

A Novel Ultrasonic Atomization Process For Producing Spherical Metal Powder

High-quality Spherical Zirconium Alloy Powders Prepared by Thermal Plasma Treatment for Additive Manufacturing

Fabrication of Spherical Steel Powder with Superequilibrium Nitrogen Content for Laser Powder Bed Fusion Additive Manufacturing

Novel Controllable Solid/hollow T'-YSZ Nanostructured Powders for Additive Manufacturing

High-temperature ball milling: An efficient method to fabricate Ti and its alloy powder for additive manufacturing

Characterization of pre-alloyed NiTi powders produced by electrode induction-melting inert gas atomization for additive manufacturing