Abstract:This work investigates the heterogeneous deformation and failure of HR3C austenitic stainless steel welded joints at room and typical service temperatures. Such types of welded joints are widely used in the new generation of fossil fuel power stations and are known to suffer from premature high temperature failure. Observation of in-service failures revealed that cracks may nucleate either in the heat affected zone or in the weld metal. The main objective of this work is to identify the local microstructural conditions and stress–strain fields responsible for both ductile failure and micro-crack nucleation within the weldment at low and high temperatures, respectively. To that purpose, a novel multi-scale micromechanics-based modelling framework is proposed. It relies on representative weld microstructure models digitally reconstructed from EBSD measurements, and dislocation density-based crystal plasticity models to describe the behaviour of individual grains in each weld region. A novel thermo-dynamically consistent relation for the configuration stored energy per unit volume is derived from the crystal plasticity framework. The single crystal models are calibrated and validated from a combination of uniaxial tensile tests on cross-weld specimens using high resolution digital image correlation techniques, representative volume elements of the polycrystals at the macro-scale, as well as micropillar compression tests at the scale of the individual grains. Predictions of heterogeneous inelastic deformation fields within the weldment at both 22 °C and 665 °C, and of micropillar compression behaviour of the individual weld single crystal phases are consistent with experimental data. The experimentally observed ductile failure of the weld metal at room temperature is successfully predicted using a Gurson-type void nucleation, growth and coalescence constitutive model. The suitability of the stored strain energy density and the accumulated plastic strain as crack initiation/creep failure indicators is investigated. It was found that predicted creep lifetimes with either indicator were very similar, and that they were relatively accurate for low stress levels.

Mechanism-related Modelling of Pit Evaluation in the CrNiMoV Steel in Simulated Environment of Low Pressure Nuclear Steam Turbine

An Insight into the Creep-Fatigue Damage Localization in Welded Joints Based on Crystal Plasticity Finite Element Method

Thermal, metallurgical and mechanical analysis of circumferentially multi-pass welded P92 steel pipes

Micro-mechanics investigation of heterogeneous deformation fields and crack initiation driven by the local stored energy density in austenitic stainless steel welded joints

Microscopic investigation on pitting corrosion of Ni-Cr-Mo-V high-strength steel weldment in simulated deep-sea environment

Investigation of Local Brittle Zone in Multipass Welded Joint of NiCrMoV Steel with Heavy Section

Modelling of Q&P Steel Heat Treatment Process Based on Finite Element Method

Anisotropic 3D Growth of Corrosion Pits Initiated at MnS Inclusions for A537 Steel During Corrosion Fatigue

Pit growth kinetics of additively manufactured MoNi over-alloyed type 316L stainless steel

Visualization and Location Determination of Pit Initiation Sites in Martensitic Stainless Steel during Corrosion-Fatigue Cyclic Plastic Deformation

Analytical Model to Compare and Select Creep Constitutive Equation for Stress Relief Investigation during Heat Treatment in Ferritic Welded Structure

Evolution of microsegregation-induced precipitations and bending fracture mechanisms of 9% Ni steel weldments filled with nickel-based alloys

Effect of Microstructure Evolution Caused by Welding Process on Pitting Behavior of 321 Stainless Steel

Modeling of Austenitization Kinetics in 5CrNiMoV Steel

Experimental microstructure evolution and cutting simulation for dynamic mechanical behaviors of 18CrNiMo7-6 steel considering heat treatment conditions

Promotion of pitting corrosion at hydrogen-enriched α/γ phase boundaries in austenitic stainless steel weld joints

Finite element and experiment analysis of welding residual stress in S355J2 steel considering the bainite transformation

Numerical Modelling of Chamfer Billet of High Carbon Steel During Continuous Casting

Modeling and Simulation of Pore Formation in a Bainitic Steel During Creep

Numerical and experimental study on thermal-metallurgical-mechanical behavior of high-strength steel welded joint

Formation mechanism and control of a kind of pit-shaped defect in Cf53 rolled products