Abstract:The wettabilities of molten metals on ceramics are poor normally. In order to improve the wettability, all existing ceramic brazing methods introduce a compound transition layer that is formed by the reaction of active metal and ceramic. The transition layer between brazing seam and ceramic however creates negative effect on the properties of brazing joints. This paper reports our study of the wetting effect of sputtered Al particles on AlN, which enables the direct brazing of AlN using deposited Al-based films as fillers, thereby eliminating the need of a transition layer. The results show that under the bombardment of energetic sputtered Al particles, Al-N chemical bonding is formed at the interface between Al film and AlN, which typically requires temperatures above 850 ℃, much higher than the melting point of Al. The bonding remained intact even after the Al film has been melted, achieving the wetting effect on AlN. As a result, the direct brazing of AlN without the need of a transition layer becomes feasible. The shear strength of Al/AlN joint using this process reaches 104 MPa. The addition of 3.8 at.% Cu to film fillers increases the shear strength to 165 MPa. The fracture is generated in metallic brazing seam in both cases. When Cu content increases to 9.1 at.%, the segregation of Cu at the interface between the brazing seam and the ceramic reduces the shear strength of the joint to 95 MPa. With Al-20 at.% Ge, the brazing temperature can be lowered to 510 ℃, although the segregation of Ge at interface results in a low shear strength of 48 MPa. Instead of the traditional use of molten metals, utilization of the metallic vapor particles to bombard AlN achieves the wetting and the direct brazing of ceramics, with no negative effect of transition layers. This breakthrough method provides a brand new perspective to the technique of ceramic brazing.

Direct Brazing of Al/Al$lt;inf$gt;2$lt;/inf$gt;O$lt;inf$gt;3$lt;/inf$gt; not Based on Wettability of Molten Metal

"Wetting" and Brazing of Aln by Sputtered Al

Microstructure and Mechanical Properties of Al2O3/Cu Joints Brazed with Ag–Cu–Ti+Zn Composite Fillers

Brazing Ti-48Al-2Nb-2Cr Alloys with Cu-Based Amorphous Alloy Filler

Processing, microstructure and mechanical properties of vacuum-brazed Al 2O 3/Ti6Al4V joints

Microstructure and Mechanical Properties of Transparent Alumina and TiAl Alloy Joints Brazed Using Ag-Cu-Ti Filler Metal

Wetting and Brazing of Chromium Film-Deposited Alumina Using AgCu Filler Metal

Active Brazing of Alumina and Copper with Multicomponent Ag-Cu-Sn-Zr-Ti Filler

Ultrasonic-assisted brazing of sapphire with high strength Al–4.5Cu–1.5Mg alloy

Research of Alumina and Brazing Filler Metal Interface

Ultrasound-assisted Brazing of Cu/Al Dissimilar Metals Using a Zn–3Al Filler Metal

Brazing Al2O3 to 4J42 Using Ag–Cu–Ti/Cu/BNi-2 Composite Fillers with Different Thicknesses of Cu Interlayer

Process of indirect brazing alumina to 5A05 Al alloy

Reactive Air Brazing of TiAl Alloy Using Ag-CuO: Microstructure and Joint Properties

Secondary Phase Interaction at Interfaces of High-Strength Brazed Joints made using Liquid Phase Sintered Alumina Ceramics and Ag-Cu-Ti Braze Alloys

Low-temperature diffusion brazing of actively metallized Al 2 O 3 ceramic tube and 5A05 aluminum alloy

Brazing ZTA Ceramic and Ti6Al4V Alloy Directly in Air: Excellent Oxidation Resistance at 800 °C

Interfacial reaction of intermetallic compounds of ultrasonic-assisted brazed joints between dissimilar alloys of Ti-6Al-4V and Al-4Cu-1Mg

Interfacial Microstructure Evolution and Mechanical Properties of Al2O3/Al2O3 Joints Brazed with Ti–Ni–Nb Filler Metal.

Microstructure evolution and mechanical properties of ZrO 2 /TiAl joints vacuum brazed by Ag–Cu filler metal

Ultrasonic-assisted brazing of Al/Fe with Al alloy