Abstract:The downhole casing and tubing in thermal recovery wells are the main channels for fluid flow. The corrosion for casing and tubing in high pressure (5 MPa) and high temperature (200 °C) (HPHT) fluid can cause string failure due to wall thinning, deformation, and fracture. In order to study the corrosion characteristics of J55 casing steel and N80 tubing steel in HPHT environment containing CO2 and NaCl, corrosion and corrosion inhibition experiments were carried out using a rotating autoclave at a pressure of 5 MPa and 50–200 °C environment. Morphologies and compositions of corrosion products were analyzed by SEM and XRD. HPHT corrosion process was discussed by Arrhenius equation and the transition state equation. Results showed that the corrosion rates of the two materials increased with CO2 partial pressure while increased initially and then decreased with increasing temperature. In CO2–NaCl solution, the saturate NaCl decreased the CO2 corrosion rates at low temperature (inhibition) and increased CO2 corrosion rates at high temperature. Meanwhile, SEM results showed that the surfaces of CO2 corrosion became more dense and uniform at high temperature. The increase of NaCl leaded to pitting and high concentration NaCl solution causes granular products to appear on the CO2 corrosion surface. The carbon steel corrosion rate is mainly controlled by kinetic parameters of activation; the activation parameters were increased by the increase in temperature and NaCl concentration. Oil-soluble imidazoline acts as a good inhibitor for corrosion of J55 and N80 in this work.

Development and Properties of Reference Electrode for Electrochemical Corrosion in High Temperature and High Pressure Environment

Research on Electrochemical Behaviour of Reference Electrodes for Corrosion Test under High Hydrostatic Pressure for Simulating Deep-Sea

PRESENT STATUS AND DEVELOPMENT ON ELECTROCHEMISTRY AT HIGH TEMPERATURES AND HIGH PRESSURES AQUEOUS SYSTEMS

Preparation and Characterization of the Solid‐state Ag/AgCl Reference Electrode for RC Structures

A Flexible Reference Array Electrode Technique for in Situ Imaging the Corrosion of Q235 Carbon Steel Welded Joints

Electrochemical corrosion behavior of high strength steel in simulated deep-sea environment under different hydrostatic pressure

Long-Term Performance of Ag/AgCl Reference Electrodes for Corrosion Potential Monitoring in Radioactive Tank Waste at the Hanford Site

Design of P110 steel wire beam electrode for high temperature and pressure environment and application for revealing corrosion mechanism

Development of a Scratch Electrode System in High Temperature High Pressure Water

STUDY ON INFLUENCE OF HCl UPON HIGH-TEMPERATURE CORROSION BEHAVIOR FOR SUPERHEATER TUBES

Study on High Temperature Corrosion Resistance of Domestic Super 304H Heat Resistant Steel in Real Furnace

Corrosion of high-strength steel in 3.5% NaCl solution under hydrostatic pressure: understanding electrochemical corrosion with tensile stress coupling

Study on the CO2 Corrosion Electrochemical Characteristics of 13Cr Steel at High Temperature and High Pressure

Corrosion of an Austenitic Heat-Resistant Steel HR3C in High-Temperature Steam and Supercritical Water

Hydrostatic pressure effects on corrosion behaviour of X80 steel in artificial sea water

Tribocorrosion of 316L stainless steel by in-situ electrochemical methods under deep-sea high hydrostatic pressure environment

In Situ Measurement Of Electrical Resistivity And Seebeck Coefficient Simultaneously At High Temperature And High Pressure

Experimental Study on Corrosion of J55 Casing Steel and N80 Tubing Steel in High Pressure and High Temperature Solution Containing CO2 and NaCl

Electrochemical Corrosion Behavior and Mechanism of N80 Steel in the Aqueous Solution of Carbon Dioxide under High-Temperature High-Pressure

Experimental Study on Corrosion Performance of Oil Tubing Steel in HPHT Flowing Media Containing O2 and CO2

Research in Alternating Corrosion on the Quench Oil/diluted Steamheat Exchanger Tubes of Ethylene Plant