Abstract:The microstructure and mechanical properties of a novel Cr and Si co-alloying Fe–0.6C–15Mn steels, labeled as 2Cr(3Si), 4Cr(3Si), 6Cr(3Si), and 4Cr(0Si), were investigated. All samples for mechanical property test and microstructure analysis were subjected to solution treatment at 1100 °C for 1 h after forging. The results indicate that the microstructure for the 2Cr(3Si), 4Cr(3Si) and 4Cr(0Si) steels mainly consists of the full austenite, and grain size is about 100 μm, whereas the microstructure of the 6Cr(3Si) steel exhibits austenite and some undissolved Cr 7 C 3 carbides. The refined austenite grain size of 48 μm is obtained in 6Cr(3Si) steel. The strength and elongation of the experiment steels with Si and Cr increase significantly with the Cr contents. Among the steels, the 6Cr(3Si) steel has the maximum yield strength, tensile strength and elongation of 490 MPa, 987 MPa and 41.5%, respectively. And the impact toughness is 151 J cm −2 . The Si-free steel (4Cr(0Si)) exhibits a low yield strength (372 MPa) and a high tensile strength (992 MPa). The high elongation of 74.8% and impact toughness of 320 J cm −2 are obtained. The results also demonstrate that the Cr and Si co-alloying in high-Mn steels is beneficial to improve work hardening capability, and the work hardening capability increases with the increase of Cr content. According to the results analyzed by the electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM), the strain-induced ε -martensite is dominant at the low strain level and the content of ε -martensite increases with the increase of the tensile strain. The maximum amount of the ε -martensite is found in the 6Cr(3Si) steel. With the strain increasing, α '-martensite appears in microstructure, which is formed on the ε -martensite. In addition, the stacking faults (SF) and mechanical twins (MT) are also observed.

Cold Crack Implant Test Study of Superhigh Strength Steel 30Crmnsini2a

Use of Instrumented Micro-Indentation to Study the Mesoscopic Elasto-Plastic Behavior of Gh4145/Sq Superalloy During High-Temperature Cyclic Straining

Cracking in a Fe–25Mn–3Si–3Al Steel

In-situ investigation of fatigue crack growth behavior of 34CrNi3Mo high-strength steel

Effect of Cr on solidification structure and microhardness of Al-Ni alloy

Effect of Holding Time on Microstructure and Mechanical Properties of Isothermally Treated High Strength Steel 30Crmnsi2ninb

Correlation between crystal structure and mechanical performance of Cr-implanted 300M high-strength steel using X-ray diffraction method

Investigation on the hot crack sensitivity of a nickel-based single crystal superalloy fabricated by epitaxial laser metal forming

Microstructure and mechanical behavior of a novel Fe–Mn–C–Cr–Si high-manganese steel

Tailoring Strength and Ductility of a Cr-Containing High Carbon Steel by Cold-Working and Annealing

Experimental study on fracture toughness of high-strength structural steel and its butt weld

Study on Micro-Mechanism of Crack Initiation and Propagation Induced by Inclusion in Ultra-High Strength Steel

Study of Crack Sensitivity of Peritectic Steels

Tensile properties and strain hardening mechanism of Cr-Mn-Si-Ni alloyed ultra-strength steel at different temperatures and strain rates

Effect of Recrystallization Annealing on Microstructure and Tensile Properties of Inconel 617B Alloy Cold Rolled Pipes

Experimental study on fracture toughness of high-strength structural steel and its

Effect of tempering and deep cryogenic treatment on microstructure and mechanical properties of Cr–Mo–V–Ni steel

Study on Cold Hardening and Recrystallization Temperature of Cu-Ni-Sn-P Alloy for Integrated Circuit Lead Frame

Cold Deformation and Hardness on Superaustenitic Stainless Steel: Evaluation Methods

Effect of Nickel Content on Mechanical Properties of 2200 MPa Grade Ultra-High Strength Steels

Experimental Research on Cracking Behavior During High-Power CO 2 Laser Cladding