Abstract:An X-band linac is designed to produce beam energy between 0.5MeV and 1.5MeV, and the output beam energy is continuously adjustable within this range. Two sections of linacs are combined and powered by a single microwave source. By tuning the RF phase and amplitude of the second section of the linac, the electron beam can see either acceleration or deceleration, which tunes the output energy. This paper presented the principle and the design of the linac, as well as the production of the whole system. INTRODUCTION In x-ray imaging, appropriate x-ray energy is required for different substances to meet a better sensitivity. The energy varies from several hundreds of keV to several MeV. In the low energy end, x-ray tubes has been well developed. However, tubes with energy higher than 500keV is not easy to obtain. Linacs with energy at MeV levels are also adopted in the industrial for radiographic applications such as non-destructive test and cargo inspection. From non-destructive testing for industrial inspection, to the industrial CT, to the container inspection, security, and even material inspection, all need to use two or more kinds of energy accelerator as X-ray source[1]. We propose an electron linac that may produce electron beam with energy between 0.5MeV to 1.5MeV. It has a wide range of applications in such aspects as medical imaging, non-destructive flaw detection. MAIN PRINCIPLE Being different from single accelerating tube, the accelerator tube is separated into two sections. By changing the amplitude and phase of the second linac section, it is possible to realize the change of energy continuously. The principle of changing the beam energy is described as follows: The energy of the electron beam is correlate with the acceleration phase. If the accelerating tube is divided into two segments, the first section accelerates the electron energy to E1, and the second section of the accelerating tube can accelerate the electrons to an Energy of E2 while the phase is adjustable, so the final energy is (see Eq. 1): 1 2 cos E E E    . (1) For example, we accelerate the second part’s energy to E2 and switch its phase position to 0°, so the final energy is E1+E2. If we switch the second part’s phase position to 180°, so the final energy is E1-E2. By choosing E1=1MeV and E2=0.5MeV, the total energy can be continuously adjusted between 0.5 and 1.5MeV. Figure 1 shows the schematic diagram of the system configuration of the X-band linac. The RF power is supplied by one source, which is a magnetron in this design. The power is divided into two parts: one is fed into the first accelerating section directly; the other is fed into the second accelerating section through an attenuator and a phase shifter, which are used to change the amplitude and the phase of the second tube. Figure 1: Schematic diagram of the linac system. THE ACCELERATOR TUBE The first accelerator section is a 6-cell pi-mode structure. The electron beam from the DC gun is bunched by the first cell and further accelerated by the following 5 cells. The second section is a 2-cell pi-mode structure. We choose on-axis magnetic coupling through kidney shaped holes between the cells. The coupling coefficient is designed to ensure a large mode separation between the πmode and the π-1 mode. Since there are only 6 cells in the first section. It is not difficult to have a 10MHz mode separation if the coupling coefficient between the adjacent cells is 0.02. Cell geometries are simulated in SUPERFISH and the field is exported into PARMELA to do a particle tracking simulation. The longitudinal electric field on axis used in ___________________________________________ *Work supported by Tsinghua University Initiative Scientific Research Program No. 20131080112 #zhangliang13@mails.tsinghua.edu.cn # WEPH22 Proceedings of SAP2014, Lanzhou, China ISBN 978-3-95450-171-7 68 C op yr ig ht © 20 14 C C -B Y3. 0 an d by th e re sp ec tiv e au th or s

THE STUDIES FOR ADJUSTABLE ENERGY OF PROTON BEAMS FROM PROTON LINEAR ACCELERATOR

Physics design of phase and energy adjustment for heavy ion beam of the same mass with two-charge state on BISOL

High Intensity Proton Beam Transportation Through Fringe Field of 70 MeV Compact Cyclotron to Beam Line Targets

Beam Dynamic Design and Study of a Linac with Variable Output Energy for an AB-BNCT Facility

RF measurement and tuning for an Alvarez-type drift tube linear accelerator without post couplers

The optimization for the conceptual design of a 300 MeV proton synchrotron

The design study for a 500 MeV proton synchrotron with CSNS linac as an injector

Design of a 10 MeV normal conducting CW proton linac based on equidistant multi-gap CH cavities

An x-band linear accelerator with continuously- adjustable beam energy *

Beam-energy-spread Adjustment Using Cell-Timing Asynchronization

The Adjustment Of Rf System For Hefei Storage Ring

A Novel Adjustable Aperture for Beam Current Controlling at China-ADS Low Energy Beam Transport Line

Development of a Beam Energy Adjustment System after a Radio-Frequency-Quadrupole

S-band high-gradient low single-periodic magnetically coupled standing-wave accelerating structure for a proton therapy linac

Design of a Low-Energy Proton Facility for Space Radiation Effect Research Based on a Compact Neutron Source

Beam dynamics framework incorporating acceleration to define the minimum aperture in two focusing schemes for proton radiotherapy linac

Research on Longitudinal Dynamics and Design of RF Parameters of Synchrotron for XiPAF-upgrading Project

Beam Commissioning for a Superconducting Proton Linac

Design study for medium energy high intensity proton accelerator

BEAM DYNAMICS DESIGN AND ERROR STUDY OF THE 5mev RFQ

A Preliminary Study of the Feasibility of Using Superconducting Quarter-Wave Resonators for Accelerating High Intensity Proton Beams