SCM AT89C52- Based Controller for Laser Ranging

胡腾飞,张永德,于爽

DOI: https://doi.org/10.3969/j.issn.1003-7241.2004.03.023

2004-01-01

Abstract:This paper presents the SCM AT89C52-based controller for a laser ranging device.A portable controller is designed and implemented with RS232C.In combination with the controller,the ranging device becomes more flexible to use.

What problem does this paper attempt to address?

Design of an Autonomous and Controllable Laser Ranging System

Wei Fuli,Bin Tang,Zourong Long,Yong He,Lang Li,Siyue Lei,Lihua Xie,Lei Deng,Mingfu Zhao

DOI: https://doi.org/10.1117/12.3025201

2024-01-01

Abstract:In order to solve the problems of low localization rate and poor stability of laser ranging system, a system based on the TDC-GP22 timing unit and the pulsed laser ranging method in the time-of-flight (TOF) method is designed to realize laser ranging. The domestic AL0905P75WT18-03FW laser diode and power MOS tube are used as the laser transmitter module to realize the high stability of laser emission, and the domestic AA-S0905 L0500 LCC3-2-B avalanche diode is used as the laser detector to convert the optical signal into current signal, which is further processed by amplification, filtering and so on and then passed through the TDC-GP22 to realize the laser distance measurement. After further processing, the light signal is converted into current signal through amplification, filtering and other further processing, through TDC-GP22 timing, thus realizing laser distance measurement. The system adopts domestic light source and photodetector, domestic voltage regulator chip, operational amplifier and FPGA chip, which improves the reliability, stability and autonomy of the system.
The Laser Machine Controller Based on SCM MSP430

SHI Hong,HU Teng-Fei,ZHANG Yong-de

DOI: https://doi.org/10.3969/j.issn.1003-7241.2007.06.038

2007-01-01

Abstract:This paper introduces a controller for the laser distance detector based on SCM MSP430.RS232C is used to control the communication,and a convenient pocket controller is designed and manufactured.
Design of temperature control box of laser rangefinder based on DS18B20

Wang Minghua,Zhang Chu,Zhang Chengdong

DOI: https://doi.org/10.3969/j.issn.1672-7916.2011.04.018

2011-01-01

Abstract:The temperature of the temperature control box of laser rangefinder was measured by STC89C52 SCM and DS18B20 digital temperature sensor,and then compared with the pre-set temperature.According to the results of the comparison,controls the onoff of the heating resistor and the thermal electrical cooler,so as to achieve the purpose of temperature control.
Design and fabrication of a high-precision 360 laser receiver for leveling applications

Xianfan Wang,Jianhua Yang,Tengchao Huang

DOI: https://doi.org/10.1002/mop.32382

IF: 1.311

2020-01-01

Microwave and Optical Technology Letters

Abstract:The laser technique based sensors and actuators can provide many superior properties as noncontact, high sensitivity, remote operation, and reliable performance in contrast to other mechanical and electrical techniques. In this paper, we design and fabricate a high-precision 360 degrees laser receiver for leveling, especially for agricultural and construction field. The laser receiver is primarily composed of photoelectrical conversion module, electrical signal processing module, and display panel module. Based on the centroid method, the detection error of the laser receiver with respect to laser source and silicon photocell array, is analyzed and simulated. The design and fabrication process are described in detail, including the overall structure and electrical circuits. Furthermore, this fabricated laser receiver is demonstrated to be high precision through several static and dynamic tests in the distance of 10 and 50 m. Besides, this fabricated laser possesses wireless transmission function, which provides much convenient for users in remote operation.
Design and implementation of embedded signal processing system based on pulsed laser ranging technology

JIANG Shuixiu,BAI Jian

DOI: https://doi.org/10.3969/j.issn.1005-5630.2008.03.010

2008-01-01

Abstract:The pulsed laser ranging measurement is an advanced and universal test method.This paper introduces the design and implementation of embedded signal processing system based on pulse laser ranging technology.It mainly discusses the design of the circuit based on the variable gain amplifier and the high speed A/D converter.The hardware and the software of the signal processing system are also presented.It realizes a high accuracy time interval measurement.Here develop an embedded measuring instrument based on the pulsed laser ranging design,as well as good performances and high precision laser range finding.The design is especially suit for volume-produce and low-cost requirements.
Intelligent Measuring System for Performance Parameters of Laser Range Finder

Song Li

2001-01-01

Abstract:In order to measure the performance parameters of laser range finders, a new intelligent measuring system is developed, which introduces advanced control technologies, very quick and convenient WIN32 computer software and a skillfully designed beam splitter system. It can synchronously measure optical axis consistency, width and energy of the pulse, beam divergence angle, and so on. A 1296×1030 CCD is adopted in order to ensure 10″ of spatial resolving ability; A 350MHz oscilloscope is used to catch the laser pulse as narrow as 10ns; A laser power meter which has high accuracy and large dynamic scope is used to obtain accurate energy measurement of the laser pulse. The system has been checked and accepted, and all the performance parameters meet the design demands. Now it is used by user and operates very well.
Airborne Laser Communication System with Automated Tracking

Xizheng Ke,Hanli Liang

DOI: https://doi.org/10.1155/2021/9920368

2021-05-25

International Journal of Optics

Abstract:The acquisition, alignment, and tracking system is an important part of airborne laser communication and is the prerequisite and guarantee for the normal communication link. In order to solve the problem of automatic tracking of laser communication links in the airborne environment, the rapid capture, alignment, and tracking of beams between terminals are realized. This article proposes a stepping motor as a control servo system and a four-quadrant detector as an automatic tracking method for the detection unit. The pulse width modulation signal controls the rotation speed of the stepping motor and combines the position distribution of the light spot on the four-quadrant detector to achieve high-precision beam tracking. On this basis, indoor simulation experiments are carried out. After many experiments, the tracking accuracy is better than 2.5 μrad, which shows that the system can be applied to airborne laser communication, and it is verified that this method has good automatic tracking performance for airborne laser communication.

optics
Implementation of Serial Communication between PLC and Single-chip Microcomputer

Cheng Liang,Lin Bin,Cha Lingzhi

DOI: https://doi.org/10.3969/j.issn.1000-3886.2006.03.013

2006-01-01

Abstract:This paper introduces serial communication between PLC and single-chip microcomputer with the example of S7-226 PLC and AT89S51 MCU.Detailed explanation of hardware configuration and program design in this communication system is given.The design project in paper has been applied successfully in automatic pill-filled machine.
Research of maintenance training platform for the laser range finder based on GL Studio

Wang Minghua,Zhang Chu,Lin Dejiang

2012-01-01

Abstract:In combination with VC++6.0 and Multisim,the simulation of the maintenance training platform for the laser range finder is realized with the graphic designer and code editor of GL Studio.The paper introduces the main characteristic and functions of GL Studio,and then brings forward the idiographic process to develop virtual panels based on GL Studio.The logistic of the virtual panel is introduced in details.At last,the pivotal technology of mixed programming with GL Studio and MFC and Multisim is present.The favorable effects have been gained in the exploitation of practical projects.
Serial Communication Controlling LCM Displaying Based on AT89S52

HE Xiu-ling,GAO Huan-zhi,LI Fang,ZHANG Heng

2008-01-01

Abstract:The system realizes serial communication between AT89S52 MCU and PC, and can drive the LCM device to display specifi-cally characters by operating PC end software, which designs to realize the function of the MCU driving drive the LCM device to dis-play characters under PC end. The whole system consist of three parts: PC end software, MCU system, LCM drives .The PC end software uses JAVA2 platform.
The Design and Application of an Altimeter System Based on 89C52

YUAN Jie,HAN Bo,LI Ping

DOI: https://doi.org/10.3969/j.issn.1001-4551.2005.10.009

2005-01-01

Abstract:This paper accounts for the design problem of an altimeter system based on 89C52,which is an 8 bit microcontroller produced by ATMEL. Specially,it depends on the relationship between pressure,temperature and altitude.The most important points in this paper is that it uses the I/O in 89C52 to achieve the function of SPI,which makes the A/D function come true with TLC2543.Thereafter it transfers the data which is processed to the LCD,also it returns the data to the control computer through RS232.
Improvement of Ultrasonic Distance Measuring System

Yu Jiang,Rui Song,Mingting Yuan

DOI: https://doi.org/10.1051/itmconf/20181702008

2018-01-01

ITM Web of Conferences

Abstract:This paper mainly introduces a kind of ultrasonic distance measuring system with AT89C51 single chip as the core component. The paper expounds the principle of ultrasonic sensor and ultrasonic ranging, hardware circuit and software program, and the results of experiment and analysis.The hardware circuit based on SCM, the software design adopts the advanced microcontroller programming language.The amplitude of the received signal and the time of ultrasonic propagation are regulated by closed loop control. [1,2]The double closed loop control technology for amplitude and time improves the measuring accuracy of the instrument. The experimental results show that greatly improves the measurement accuracy of the system.
Research on the Position-Controller for Lifted Hoist Based on Single-Chip Microcomputer

Gang Shen,Qitao Huang,Da-cheng Cong,Guang-ming Lv,Jun-wei Han,Yandong Pi

DOI: https://doi.org/10.1061/40996(330)261

2009-01-01

Logistics

Abstract:The cage will be properly positioned by comparing the number of scaling program with the number from the calculation for the pulse in position detection device that has been designed and manufactured. We select AT89C52 as the CPU of position-controller and use new style interface chip BC7281A to realize input and display of the layer number and take use of ISD1420 voice device to realize attention voice. The software of control system is made with C51. At the same time, we designed several anti-interference methods in the hardware and software. After debugging, this position-controller works very well.
The Design of the Synchronization Control Circuit Based on Cpld for the Range-Gated Laser Imaging System

XW Xu,XH Wang,F Tang,QY Yu,J Guo

DOI: https://doi.org/10.1117/12.667337

2006-01-01

Abstract:The synchronization control technique is one of the most key techniques in the laser range gated (LRG) imaging system. Conventional control circuits are composed of discrete components and Medium Scale Integration (MSI) and Small Scale Integration (SSI), which have bad reliability and poor ability of anti-interference. The idea of using the Complex Programmable Logic Device (CPLD) to realize the monostable trigger circuit is introduced. On the basis of analyzing the performance requirement to the synchronization control of the laser range gated imaging system, a new synchronization control circuit based on CPLD is presented. The circuit based on CPLD is very compact and flexible and has high reliability and strong ability of anti-interference. The synchronization control circuit based on CPLD can provide a wide selection of gate widths, pulse widths and delays. The synchronization control circuit is successfully used in our experiment and the expected result is obtained.
Long Distance Monitoring and Controlling System Based on AT89S52

XU HAIBO,LIAO CHUANSHU

DOI: https://doi.org/10.3969/j.issn.1008-0570.2007.20.026

2007-01-01

Abstract:At now, with the fast development of the applied technology of the Single-chip Microprocessor, the embedded systems with the core of Single-chip Microprocessor have been used in many fields. In this paper, there is a project of a Long Distance Auto-matic Monitoring and Controlling System for Alarm, which is constituted by the AT89S52 and the chip of the DTMF.
Study on position-controller for elevator based on AT89C52

SHEN Gang,CONG Da-cheng,LV Guang-ming,HAN Jun-wei

DOI: https://doi.org/10.3969/j.issn.1001-4551.2008.09.017

2008-01-01

Abstract:Aiming at improving position precision of elevator,AT89C52 was used as the CPU of position-controller,the number of scaling program with the number from the calculation for the pulse in position detection device were compared.The new style interface chip BC7281A was used to realize input and display of the layer number,and the ISD1420 voice chip was used to realize attention voice.The software of control system was made with C51.The several anti-interference methods in the hardware and software were designed,and the reliability of the system was improved.The debug results indicate that the position-controller works very well,and it has high position precision.
Handheld Laser Rangefinder and Its Transmitter Circuit

ZHI Qiang,HUO Yu-jing,GONG Ke

DOI: https://doi.org/10.3969/j.issn.1001-5078.2013.05.013

2013-01-01

Abstract:A simple LD laser drive circuit was designed for pulse phase laser rangefinder,which contains the frequency synthesizer and the laser modulation circuit.This paper analyzes the effect of the circuit on the ranging range,accuracy,cycle and energy consumption,and illustrates the key points to improve laser ranging performance.Intermittent burst emission was achieved by enabling and disabling the operational transcondnctance amplifiers(OTA).This intermittent burst emission heightens the laser peak power,which can enhance the measurement range.This circuit design is simple and feasible,and has cerctain reference value for the handheld laser rangefinder developing.
A New Synchronization Control Circuit Based on CPLD for the Laser Range-gated Imaging System

Xiaowen Xu,Xiaohao Wang,Fei Tang,Qianyang Yu,Jin Guo

DOI: https://doi.org/10.1117/12.667337

2006-01-01

Abstract:The synchronization control technique is one of the most key techniques in the laser range gated (LRG) imaging system. Conventional control circuits are composed of discrete components and Medium Scale Integration (MSI) and Small Scale Integration (SSI), which have bad reliability and poor ability of anti-interference. The idea of using the Complex Programmable Logic Device (CPLD) to realize the monostable trigger circuit is introduced. On the basis of analyzing the performance requirement to the synchronization control of the laser range gated imaging system, a new synchronization control circuit based on CPLD is presented. The circuit based on CPLD is very compact and flexible and has high reliability and strong ability of anti-interference. The synchronization control circuit based on CPLD can provide a wide selection of gate widths, pulse widths and delays. The synchronization control circuit is successfully used in our experiment and the expected result is obtained.
The Short-Range, High-Accuracy Compact Pulsed Laser Ranging System

Hongbin Ma,Yuan Luo,Yan He,Shiguang Pan,Lihong Ren,Jianhua Shang

DOI: https://doi.org/10.3390/s22062146

2022-03-10

Abstract:A short-range, compact, real-time pulsed laser rangefinder is constructed based on pulsed time-of-flight (ToF) method. In order to reduce timing discrimination error and achieve high ranging accuracy, gray-value distance correction and temperature correction are proposed, and are realized with a field programmable gate array (FPGA) in a real-time application. The ranging performances-such as the maximum ranging distance, the range standard deviation, and the ranging accuracy-are theoretically calculated and experimentally studied. By means of these proposed correction methods, the verification experimental results show that the achievable effective ranging distance can be up to 8.08 m with a ranging accuracy of less than ±11 mm. The improved performance shows that the designed laser rangefinder can satisfy on-line ranging applications with high precision, fast ranging speed, small size, and low implementation cost, and thus has potential in the areas of robotics, manufacturing, and autonomous navigation.
An embedded laser marking controller based on ARM and FPGA processors.

Wang Dongyun,Ye Xinpiao

DOI: https://doi.org/10.1155/2014/716046

2014-01-01

Abstract:Laser marking is an important branch of the laser information processing technology. The existing laser marking machine based on PC and WINDOWS operating system, are large and inconvenient to move. Still, it cannot work outdoors or in other harsh environments. In order to compensate for the above mentioned disadvantages, this paper proposed an embedded laser marking controller based on ARM and FPGA processors. Based on the principle of laser galvanometer scanning marking, the hardware and software were designed for the application. Experiments showed that this new embedded laser marking controller controls the galvanometers synchronously and could achieve precise marking.

SCM AT89C52- Based Controller for Laser Ranging

Design of an Autonomous and Controllable Laser Ranging System

The Laser Machine Controller Based on SCM MSP430

Design of temperature control box of laser rangefinder based on DS18B20

Design and fabrication of a high-precision 360 laser receiver for leveling applications

Design and implementation of embedded signal processing system based on pulsed laser ranging technology

Intelligent Measuring System for Performance Parameters of Laser Range Finder

Airborne Laser Communication System with Automated Tracking

Implementation of Serial Communication between PLC and Single-chip Microcomputer

Research of maintenance training platform for the laser range finder based on GL Studio

Serial Communication Controlling LCM Displaying Based on AT89S52

The Design and Application of an Altimeter System Based on 89C52

Improvement of Ultrasonic Distance Measuring System

Research on the Position-Controller for Lifted Hoist Based on Single-Chip Microcomputer

The Design of the Synchronization Control Circuit Based on Cpld for the Range-Gated Laser Imaging System

Long Distance Monitoring and Controlling System Based on AT89S52

Study on position-controller for elevator based on AT89C52

Handheld Laser Rangefinder and Its Transmitter Circuit

A New Synchronization Control Circuit Based on CPLD for the Laser Range-gated Imaging System

The Short-Range, High-Accuracy Compact Pulsed Laser Ranging System

An embedded laser marking controller based on ARM and FPGA processors.