Abstract:The solidification path of alloy reveals the detailed relationship between the solute concentration in liquid and the temperature during the solidification process. The best and most accurate method to predict the solidification path of multicomponent/multiphase alloys is to establish proper microsegregation modeling coupled with phase diagram calculations according to the CALPHAD method. Recently, several alloy systems such as Al-Cu, Al-Mg and Cu-Mg have been developed, which have aroused the interest of many researchers. Up to now, the research about Al-Cu-Mg ternary alloy, especially containing higher Mg content, is relatively rare. The purpose of the present work is to investigate the solidification path of Al-6.32Cu-25.13Mg (mass fraction, %) ternary eutectic alloy at different cooling rates and solid back diffusion coefficients by an extended unified microsegregation model coupled with Thermo-Calc. Solidification experiments and subsequent microstructural characterization are combined with numerical calculation of solidification paths. It was shown that the cooling rates R-f had no obvious effect on the solidification path which was (L+alpha)->(L+alpha+T)->(L+alpha+beta+T); but the solid back diffusion coefficient 0 had a great effect on the solidification path, which evolved gradually from (L+alpha)->(L+alpha+T)->(L+alpha+beta+T) into (L+alpha)->(L+alpha+T) when Phi increased from 0 to 1. The volume fractions of primary alpha phase V-alpha, binary eutectic V-2E and ternary eutectic V-3E at each solidification path were calculated. It was shown that V2E decreased with the increase of R-f whereas V-3E increased and V-alpha was almost invariant. The dependence of V-2E, V-3E and R-f were determined by linear regression analysis given as: V-2E=-2.51gR(f)+64.9, V-3E=2.51gR(f)-F22.12. The increase in Phi led to increases in V-alpha and V-2E and decrease in V-3E. The predicted solidification paths and volume fractions of A1-6.32Cu-25.13Mg ternary eutectic alloy at different cooling rates were in good agreement with experimental results.

Prediction of Solidification Path of Al-1.5Cu-3Zn from Experimental Phase Diagram and Numerical Model

Phase Field Simulation for Non-Isothermal Solidification of Multicomponent Alloys Coupled with Thermodynamics Database

Calculation of Phase Diagrams and Solidification Paths of Al-rich Al−Li−Cu Alloys

Solidification Paths and Phase Components at High Temperatures of High-Zn Al-Zn-Mg-Cu Alloys with Different Mg and Cu Contents

A unified analytical model for the primary solidification path in ternary alloys

Prediction of the Solidification Path of Al-6.32cu-25.13mg Alloy by A Unified Microsegregation Model Coupled with Thermo-Calc

Thermodynamic calculation of high zinc-containing Al-Zn-Mg-Cu alloy

Prediction of the Solidification Path of Al-4.37cu-27.02mg Ternary Eutectic Alloy with A Unified Microsegregation Model Coupled with Thermo-Calc

Dendritic Solidification of Highly Undercooled Dilute Alloys

Phase-Field Simulation of Non-Isothermal Dendritic Growth of Binary Alloy

Numerical Simulation of Solute Segregation Patterns for a Binary Alloy Using Phase-Field Approach

Zone Partitioning Sequential Calculation Method for Three-Dimensional Phase-Field Material Simulation During Directional Solidification

Non-equilibrium solidification of bulk undercooled Ni–P eutectic alloys

New Insights into Solidification and Phase Equilibria in the Al-Al3Zr System: Theoretical and Experimental Investigations

Experimental determination of the phase equilibria of aluminum-rich Al−Li−Cu alloys

Solidification Curves of AlCu, AlMg and AlCuMg Alloys

Phase-Field Simulation for Non-isothermal Solidification of Al-Cu Binary Alloy

Simulation of the Dendrite Morphology and Microsegregation in Solidification of Al–Cu–Mg Aluminum Alloys

Solidification Mechanism of Ternary Quasi-Peritectic Alloy of Al-11.8cu-24.22mg

Modeling the Overall Solidification Kinetics for Undercooled Single-Phase Solid-Solution Alloys. II. Model Application

SOLIDIFICATION PHASE SELECTION IN DIRECTION-ALLY SOLIDIFIED Ti–(44%—54%)Al ALLOYS