Abstract:Shot peening (SP) can modify the surface properties of titanium alloys and titanium matrix composites (TMCs). Based on our previous work in the last ten years, the microstructure and mechanical properties of SP treated Ti-6Al-4V (TC4) and (TiB+TiC)/TC4 are summarized in this review. The compressive residual stress (CRS) was formed on the surface after SP. At different SP intensities, the thickness of the surface CRS layer was improved with increasing SP intensities. During the stress peening, the CRS increased evidently, and the increment was proportional to the prestress. Besides, CRS's thermal relaxation was investigated, which showed that the CRS in the whole deformation layer was relaxed. The relaxation mechanism could be explained by the Zener-Wert-Avrami model. The microstrain, the domain size, and the dislocation density of the peened layer were investigated using the Voigt method. The domain size of TC4 was smaller than the composite, and the microstrain of the TC4 was higher than the composite. The average dislocation density was increased after SP due to the existence of reinforcements. Utilizing the Rietveld method to analyze the microstructure after SP, the variations were similar to the Voigt method's results. Also, the composite's stability was higher than TC4 because of the existence of reinforcements. Hardness analysis revealed that the existence of reinforcements raised the hardness. In the peened layer, the surface's hardness was maximum, and it decreased with the increase in depth. At the same temperature, the hardness of the TC4 was smaller than the composite counterpart. Finally, the strengthening mechanism of SP was discussed and summarized based on the above analysis.

Characterization on Surface Properties of Ti–6Al–4V after Multiple Shot Peening Treatments

Characterization on Surface Mechanical Properties of Ti–6Al–4V after Shot Peening

The Influence of Shot Peening on the Surface Properties of (Tib+tic)/ti–6al–4v

Evaluation of Mechanical Behavior and Surface Morphology of Shot-Peened Ti-6Al-4V Alloy

Investigation of Wet Shot Peening on Microstructural Evolution and Tensile-Tensile Fatigue Properties of Ti-6Al-4V Alloy

Investigation on Experiments and Numerical Modelling of the Residual Stress Distribution in Deformed Surface Layer of Ti–6Al–4V after Shot Peening

Research on surface integrity of Ti-6Al-4V alloy with compound treatment of laser shock peening and shot peening

Residual Stress Distribution And Microstructure Characterization Of Particle Reinforced Titanium Matrix Composite After Shot Peening Treatment: A Review

The Variations of Microstructures and Hardness of Titanium Matrix Composite (tib + TiC)/Ti–6Al–4V after Shot Peening

Numerical Analysis and Experimental Validation on Residual Stress Distribution of Titanium Matrix Composite after Shot Peening Treatment

Surface mechanical property and residual stress stability of nanostructured CNT/Al-Cu-Mg composites induced by shot peening

Enhancement of Fatigue Properties of Selective Laser Melting Fabricated TC4 Alloy by Multiple Shot Peening Treatments

Microstructure and Mechanical Property of Ti and Ti6Al4V Prepared by an In-Situ Shot Peening Assisted Cold Spraying

Investigation on the Residual Stress and Microstructure of (tib+tic)/ti–6al–4v Composite after Shot Peening

Uniformity of residual stress distribution on the surface of S30432 austenitic stainless steel by different shot peening processes

Surface Mechanical Property and Residual Stress Stability of Shot-Peened Mg-8Gd-3Y Alloy by In-Situ X-ray Diffraction

Effects of shot peening on microstructure evolution and mechanical properties of surface nanocrystal layer on titanium matrix composite

Surface mechanical properties of S30432 austenitic steel after shot peening

The residual stress varying of shot peened TC4-DT titanium alloy

Effect of Ultrasonic Shot Peening on the Microstructure, Surface Residual Stress, and Wear Properties of Ti-6al-4v Alloy

Evaluation of the Residual Stress and Microstructure Character in SAF 2507 Duplex Stainless Steel after Multiple Shot Peening Process