Preparation of Nanostrured Fe - Co Alloy

董国君,王一钧

DOI: https://doi.org/10.3969/j.issn.1002-1124.2003.06.027

2003-01-01

Abstract:Fe-Co alloy were prepared in a solution of mixed ferrous and cobaltous salt,using KBH 4 as a reducing agent,polyethylene glycol as a dispersant agent.Temperature of reaction,concentration of reactants,pH and surfactant on technological process of Fe-Co alloy wer analyzed.

What problem does this paper attempt to address?

Effect of Co Addition on the Phase Structure and Magnetic Properties of Fe-Si-Al Alloys

Wang Wei,Ma Tianyu,Luo Wei,Yan Mi

DOI: https://doi.org/10.3321/j.issn:1002-185x.2008.06.032

2008-01-01

Abstract:(Fe1-xCox)(85)Si9.6Al5.4 (x=0, 0.05, 0.10, 0.15, 0.20) nanocrystalline flakes with large aspect ratio have been prepared by high-energy planetary ball milling method from melt spun ribbons. Annealing at 773 K for 30 min has been employed to the as-milled powder under the protection of nitrogen. The annealed powder is then mixed with resin to get toroidal samples of Phi 19 mm x Phi 10 mm, x 3 mm at 30 MPa. The effects of Co addition on the phase structure and magnetic properties have been discussed detailed. The results show that the Co addition doesn't change the phase structure of alloy ribbons. However, The Curie temperature has been greatly increased by Co addition; the maximum saturation magnetization is achieved when x=0.15. The toroidal samples show a good anti electromagnetic interference (EMI) performance at about 1GHz. The cutoff frequency reaches 1.154 GHz when x=0.15.
Preparation and study of Fe–Co–Zr–B nano-soft magnetic alloy

Guofeng Wang,Minghui Liu,Lizhong Wang,Hongbo Liu

DOI: https://doi.org/10.1166/mex.2019.1541

2019-09-01

Materials Express

Abstract:The mechanical alloying of Fe–Co–Zr–B mixed powder has been studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and other test methods. The results show that the Fe–Co–Zr–B nanocrystalline alloy can be produced by mechanical alloying from the elements powders by ball milling of 50 h. With the increase in Co content, the grain size increases correspondingly, and the size of composite particles decreases continuously. The mechanical alloying process of Fe–Co–Zr–B alloy system is slowed down by the addition of Co.
Preparation and application of nano-Ni–Co alloy

Xu Yang,Xuefeng Lu,Wei Zhang,Xin Guo,Junqiang Ren,Hongtao Xue,Fuling Tang,Guo, Xin

DOI: https://doi.org/10.1007/s11051-023-05799-y

IF: 2.533

2023-07-13

Journal of Nanoparticle Research

Abstract:Ni–Co alloy has high temperature resistance, corrosion resistance, excellent magnetic and catalytic capabilities, and is widely used in energy development, chemical industry, electronics, aviation and aerospace, such as combustion chamber hot end parts, aircraft engine working blades and hydrogen evolution catalysts. It is well known that the properties of materials depend on the structure and morphology, which depend on the preparation method. At present, the main methods for preparing nano-Ni–Co alloy are electrodeposition, sol–gel method and solution reduction method. The parameters in these preparation methods affect the morphology and properties of nano-Ni–Co alloy, so it is particularly important to study the influence of various parameters on the properties of Ni–Co alloy. In this work, the preparation methods and research progress of nano-Ni–Co alloy in recent decades are summarized, hoping to provide valuable information for the development of Ni–Co alloy.

materials science, multidisciplinary,nanoscience & nanotechnology,chemistry
Study of Preparation of Cobalt Aluminate by Sol-Gel Process and Electroless Plating

YAO Ji-peng,WU Tao,LI Jian

DOI: https://doi.org/10.3969/j.issn.1009-6264.2007.z1.073

2007-01-01

Abstract:Cobalt aluminate has been prepared by two different methods—sol-gel process and electroless plating,and characterized by XRD,SEM,EDX and DTA.The powder prepared by these two methods gain spinel structure at the same tempreture.The powder prepared by sol-gel meets to the stoichiometric proportion of cobalt aluminate.,but the element of Al is excessive in the powder prepared by electroless plating.Compared to sol-gel process,preparation of cobalt aluminate by electroless plating can not only gain smaller particle size and larger specific area but also control the particle size of the product and reduce the cost since Al_2O_3 substitutes for part of CoA1_2O_4 and COA1204 is more expensive.So,electroless plating is one effective method of preparing cobalt aluminate.
Advances in Preparation Study of Nano Magnetic Material Fe-Co Alloys

YUAN Pin-shi,WU Hua-qiang,CAO Yun-jie,XU Hong-yan,WANG Jun-en,DUAN Ying-jun

DOI: https://doi.org/10.3321/j.issn:1001-9731.2005.08.005

2005-01-01

Journal of Functional Biomaterials

Abstract:There was a long-standing interest in the research on the Fe-Co alloys due to their good soft magnetic properties.In this paper,various methods for the preparation of Fe-Co alloys have been presented and evaluated.The main factors,which affect the structure,morphology,and magnetic properties of the Fe-Co alloys,have been discussed,and the future researches in new directions were brought forward.
Sonochemical synthesis, structural and magnetic properties of air-stable Fe/Co alloy nanoparticles

Qiaoling Li,Hongliang Li,V. G. Pol,Ishai Bruckental,Yuri Koltypin,J. Calderon-Moreno,Israel Nowik,Aharon Gedanken

DOI: https://doi.org/10.1039/b302136j

IF: 3.3

2003-01-01

New Journal of Chemistry

Abstract:Nanoparticles of the Fe/Co alloy have been prepared by sonolysis of a Fe(CO)5 and Co(NO)(CO)3 mixture in diphenylmethane solution under argon. The as-prepared product is an amorphous material having 10 nm diameter particles. Upon annealing in argon at 600°C for 5 h, an air-stable Fe/Co alloy is formed with an increased particle size to 40 nm. The Fe/Co alloy nanoparticles have been characterized by XRD, TEM, TGA, DSC, XPS, EPR, MES and magnetic susceptibility measurements. Materials obtained under appropriate conditions possess a very high saturation magnetization of about 150–238 emu g−1 and good, soft magnetic properties (Hc=70−30 G). The nanocrystalline particles have a core-shell structure in which the iron–cobalt core is surrounded by a carbon surface layer. The stability of the nanocrystalline particle has been discussed, based on the core-shell structure.

chemistry, multidisciplinary
Crystallization Kinetics of Co-Finemet Amorphous Alloys and Magnetic Properties of Nanocrystalline Powder Cores

王贞,刘静,汪汝武,甘章华,徐勇攀,范丽霞,卢志红

DOI: https://doi.org/10.14136/j.cnki.issn1673-2812.2011.06.005

2011-01-01

Abstract:Amorphous Fe73.5-xCoxSi13.5B9Cu1Nb3（x=10,30,50） ribbons were prepared by the single copper wheel melt spinning technique in the air atmosphere.The nanocrystallization kinetics of amorphous ribbons was investigated by differential scanning calorimetry（DSC）.The apparent activation energies of amorphous ribbons were calculated by using Kissinger and Ozawa methods.It was found that the activation energies of the first crystallization reduce and those of the second crystallization rise with increasing Co content.The local Avrami parameter m for primary crystallization was calculated using Johnson-Mehl-Avrami（JMA） model.The values of the Avrami parameter showed that the primary crystallization mechanism of amorphous ribbons varied at different stages.In the initial stage,the crystallization mechanism was bulk crystallization with three dimensional nucleation and grain growth controlled by diffusion.In the following stage,it was surface crystallization with one dimensional nucleation and grain growth at a near zero nucleation rate.The variation of soft magnetic properties of nanocrystalline Fe63.5Co10Si13.5B9Cu1Nb3 powder cores as a function of milling time has been investigated.It was found that the effective permeability of the cores shows high frequency stability and decreases with increasing milling time.The quality factor increases with increasing frequency in the lower frequency range,reaches a maximum at the frequency of 80 kHz,and then decreases gradually with increasing frequency.
Preparation and Properties of Fe-Co-Ni Alloy/co0.5ni0.5fe2o4 Magnetic Composite Nanofibers

XIANG Jun,ZHANG Xiong-hui,ZHOU Guang-zhen,LI Jia-le,CHU Yan-qiu,SHEN Xiang-qian

DOI: https://doi.org/10.19476/j.ysxb.1004.0609.2013.08.027

2013-01-01

The Chinese Journal of Nonferrous Metals

Abstract:A series of Fe-Co-Ni alloy/Co0.5Ni0.5Fe2O4 composite nanofibers with average diameters from 67 to 85 nm and various alloy contents were synthesized by hydrogen-thermal reduction of Co0.5Ni0.5Fe2O4 nanofibers prepared via sol-gel methode and electrospinning. The obtained nanofiber samples were characterized by TG-DTA, XRD, FE-SEM, TEM and VSM. The results show that the mass fraction of Fe-Co-Ni alloys in the reduced products progressively increases from 15.2%to about 95.7%with increasing the reduction temperature of Co0.5Ni0.5Fe2O4 nanofibers from 290℃to 350 ℃. Meanwhile, the fiber diameter gradually decreases and the fiber surface morphology evolves toward the bead-like structures. The magnetic field dependence of the magnetization behaves as if the as-prepared Fe-Co-Ni alloy/Co0.5Ni0.5Fe2O4 composite nanofibers are single-phase magnetic materials, which indicates that the two magnetic phases in composites are effectively exchange-coupled and that the magnetization of both phases reverses cooperatively. The saturation magnetization and remanence of the samples increase monotonically with the increase of Fe-Co-Ni alloy content, while the corresponding coercivity shows a trend of first increase and then decrease. The formation of Fe-Co-Ni alloy phase can not only obviously improve the soft magnetic performance of the composite nanofibers, but also effectively realize the wide-range control for the magnetic parameters through adjusting the Fe-Co-Ni alloy content in composites.
Preparation of Sm-Co Alloy by Electrodeposition in DMF Solution

H. Feng

Abstract:Electrodeposition of Sm-Co alloy in DMF solution was studied by cyclic voltammetry and potentiostatic deposition at room temperature. The results show that small amount of water in a solution of Sm(NO 3) 3+CoCl 2+DMF blocked the electrodeposition of Sm-Co due to the formation of nonconductive Sm(OH) 3 film on the cathode surface. Citric acid could buffer the pH change and inhibit the precipitation of Sm(OH) 3 on the cathode surface which makes the co-deposition of Sm and Co easy. Potentiostatic deposition was carried out on copper electrode in Sm(NO 3) 3+CoCl 2+Citric acid+DMF solution and Sm-Co alloy films were obtained where the content of Sm could be as high as 57 56%.

Chemistry,Materials Science
Crystallization kinetics and magnetic properties of Fe 63.5Co10Si13.5B9Cu 1Nb3 nanocrystalline powder cores

Ruwu Wang,Jing Liu,Zhen Wang,Zhanghua Gan,Zhidong Xiang,Zhihong Lu,Yunbao Li,DengJing Wang,Jie Yuan,Yuhua Wang

DOI: https://doi.org/10.1016/j.jnoncrysol.2011.09.008

IF: 4.458

2012-01-01

Journal of Non-Crystalline Solids

Abstract:Amorphous ribbons of the alloy Fe63.5Co10Si13.5B9Cu1Nb3 were prepared by the standard single copper wheel melt spinning technique in air and their crystallization kinetics was analyzed by non-isothermal differential scanning calorimetry (DSC) measurements. The crystallization activation energies (Ex, Ea1 and Ea2) of amorphous ribbons calculated from Kissinger model were 448, 385 and 396kJ/mol for the first and the second crystallizations, respectively. The Avrami exponent n was calculated from the Johnson–Mehl–Avrami (JMA) equation and was used to identify the crystallization mechanism for the amorphous ribbons. The ribbons were milled into different sized flakes, which were molded subsequently to cores using 3wt.% epoxy as a binder. The effective permeability of the cores showed high frequency stability and increased with the size of the flakes. For the cores made from small sized flakes (−75μm), the quality factor was increased at high frequencies, which was attributed to the reduction in the eddy current loss.
Preparation and Microwave-Absorbing Properties of FeCo Alloys by Condensation Reflux Method

Zhen Liu,Bo Wang,Shicheng Wei,Wei Huang,Yujiang Wang,Yi Liang,Junqi Li,Xinyang Wang,Hongyi Su

DOI: https://doi.org/10.1021/acsomega.4c02330

IF: 4.1

2024-08-13

ACS Omega

Abstract:Five groups of FeCo alloy samples with different atomic ratios of Fe/Co (3:7, 4:6, 5:5, 6:4, 7:3) were prepared using the condensation reflux method. The results indicate that varying the atomic ratios of Fe/Co has a significant impact on the microstructure, electromagnetic parameters, and microwave absorption properties of FeCo alloys. As the Fe atom content increases, the morphology of the FeCo alloys transitions from irregular flower-shaped to uniformly spherical and eventually to lamellar....

chemistry, multidisciplinary
Co–Al2O3 nanocomposites powder prepared by electroless plating

C. Zhang,G.P. Ling,J.H. He

DOI: https://doi.org/10.1016/S0167-577X(03)00445-2

IF: 3

2004-01-01

Materials Letters

Abstract:In this paper, a new type of Co–Al2O3 nanocomposites powder prepared by electroless plating technique will be introduced. The raw Al2O3 nanoparticles are 10–20 nm in diameter. The Co plating was carried out at middle temperature (45–50 °C) with application of ultrasonic radiation. Plating rate was determined by measuring the weight gain of powder after plating. High-resolution transmission electron microscopy (HRTEM) reveals that Co–Al2O3 nanocomposites particles is of nearly sphere-like shape and is about 50–60 nm in diameter. X-ray diffraction (XRD) indicates that the chemical composition of plating layer is Co–P alloy. The phase structure is different when the reductant content changed. Co–P alloy was found to be amorphous in as-plating Co–Al2O3 powder and was transformed into a crystalline phase after sintering. Differential scanning calorimeter (DSC) analysis proves that such a phase transformation occurs at 203–253 °C. Different Co–P content was obtained by changing the Al2O3 load.
Synthesis, Characterization and Electrocatalytic Properties of FeCo Alloy Nanoparticles Supported on Carbon Nanotubes

Pin-Shi Yuan,Hua-Qiang Wu,Hong-Yan Xu,Dong-Mei Xu,Yun-Jie Cao,Xian-Wen Wei

DOI: https://doi.org/10.1016/j.matchemphys.2007.05.004

IF: 4.778

2007-01-01

Materials Chemistry and Physics

Abstract:FeCo alloy nanoparticles with diameters about 18nm were synthesized by wet chemical technique, which were characterized by transmission electron microscopy (TEM), X-ray powder diffraction (XRD), high-resolution transmission electron microscopy (HRTEM) and energy-dispersive X-ray spectrometry (EDX). XRD analysis indicates that the FeCo alloy nanoparticles supported on the surface of carbon nanotubes (CNTs) have body-centered cubic (bcc) phase. TEM images show that the FeCo alloy nanoparticles are in the shape of spheroid on the outer surface of the carbon nanotubes. The electrochemical behavior of film of FeCo/CNT nanocomposites was studied on a glassy carbon (GC) electrode. The cyclic voltammetry results indicate that the FeCo/CNT nanocomposites film-modified GC electrode shows highly electrocatalytic activity toward hydrogen peroxide reduction in the potassium hydrogen phthalate buffer solution, and the electrocatalytic behavior is attributed to the expected catalytic activity of nanosized FeCo alloy nanoparticles supported on the external walls of carbon nanotubes.
Study on Supercritical Hydrothermal Synthesis of CoFe2O4 Nanoparticles

D. Zhao,X. Wu,H. Guan,E. Han

DOI: https://doi.org/10.1016/j.supflu.2007.03.004

IF: 3.9

2007-01-01

The Journal of Supercritical Fluids

Abstract:CoFe2O4 nanoparticles with diameter of about 5nm were prepared at 390°C by batch supercritical hydrothermal synthesis method. It was found that the characteristic of products depended on pH, temperature, mole ratio (r) of Co2+ to Fe3+ and coexisting cations in reactant solutions. The reaction time and the coexisting cations (Na+ and K+) had little effect on the size and morphology of CoFe2O4 particles. The products were a mixture of CoFe2O4 and Fe2O3 at r<0.5 and Co1+xFe2−xO4 (0≤x≤1) at r≥0.5. Pure CoFe2O4 nanoparticles with uniform size were synthesized at 390°C, pH 12 and r=0.5. The maximum coercivity and saturation magnetization of CoFe2O4 prepared by the present method were 340.6Oe and 68.9emu/g, respectively. The mechanism for batch supercritical hydrothermal synthesis of CoFe2O4 nanoparticles is believed to be a homogeneous phase reaction of Co(NO3)2·6H2O and Fe(NO3)3·9H2O aqueous solution.
Sol-gel preparation and characterization of NiCo and Ni3Fe nanoalloys

Peng Li,Junaid Ali Syed,Xiangkang Meng

DOI: https://doi.org/10.1016/j.jallcom.2011.09.007

IF: 6.2

2012-01-01

Journal of Alloys and Compounds

Abstract:Sol-gel process is effective in preparation of metallic oxides. Here we report that sol-gel process based on chelating of citric acid is also effective in fabricating NiCo and Ni3Fe nanoalloys under N2 or H2 atmosphere during heating treatment. With the introducing of surfactant, the average grain size of the nanoalloys is less than 10 nm and the grain size distribution is narrow. The formation of nanoalloys with equilibrium ordered phase rather than metastable disordered phase is confirmed by the occurrence of superlattice diffraction rings obtained by selected area electron diffraction. The Ni3Fe nanoalloy shows typical ferromagnetic behavior at room temperature. © 2011 Elsevier B.V.
Novel Preparation and Physicochemical Characterization of a Nanocrystalline Cobalt Ferrite System

N.M. Deraz,M.K. El-Aiashy,Suzan A. Ali

DOI: https://doi.org/10.1260/0263-6174.27.8.797

2009-10-01

Abstract:Well-defined CoFe2O4 nanoparticles with an average grain size of about 50 nm were successfully synthesized by a combustion method employing different ratios of fuel to cations within the range 0–2.67. The as-prepared powders were characterized and investigated by TG, XRD, IR, SEM, TEM and VSM methods, and via isopropanol conversion at 250–450 °C. The results showed that increasing the ratio between fuel and cations stimulated the formation of cobalt ferrite due to the increasing flame temperature. Changing the fuel/cation ratio brought about modifications in the structure, surface activity, selectivity and magnetic properties of the investigated solids. A fuel/cation ratio of 2 led to the formation of catalyst having a high activity (49%) and magnetization (77.54 emu/g). All the solids investigated behaved as dehydrogenation catalysts leading to the formation of acetone as the major product. The fuel/cation ratio did not alter the mechanism of dehydrogenation of isopropanol, but increased the concentration of active sites involved in the catalyzed reaction.

engineering, chemical,chemistry, applied, physical
Large-Scale Controlled Synthesis of FeCo Nanocubes and Microcages by Wet Chemistry

Xian-Wen Wei,Guo-Xing Zhu,Yuan-Jun Liu,Yong-Hong Ni,You Song,Zheng Xu

DOI: https://doi.org/10.1021/cm800518x

IF: 10.508

2008-01-01

Chemistry of Materials

Abstract:Nanocubes and hollow cubic microcages of FeCo alloy have been synthesized in large scale by reduction of aqueous Fe2+ and Co2+ with hydrazine in the presence of poly(ethylene glycol) and cyclohexane at a relative low temperature, which were confirmed by X-ray powder diffraction, transmission electron microscopy, and scanning electron microscopy. The morphology and dimensions of FeCo alloy nanocrystals could be controlled by the reaction conditions such as the concentrations of cyclohexane and PEG-400, reaction time, and the molar ratio of Fe2+ to Co2+ in the solution. The concentration of iron in these particles could be varied between 17% and 56%. The highest magnetization of 211.9 emu/g was recorded for 68 +/- 6 nm Fe50Co50 nanocubes. The work demonstrates that are promising for single nanoparticle recording and for high performance exchange-spring nanocomposite magnetic applications.
Synthesis and Magnetic Properties of FeCo Alloy Nanoparticles by Hydrogen Plasma Metal Reaction

YH Leng,YH Zhang,XB Song,XG Li,LF Zhang

DOI: https://doi.org/10.4028/www.scientific.net/msf.475-479.2215

2005-01-01

Materials Science Forum

Abstract:Fe61Co39 nanoparticles were prepared by hydrogen plasma metal reaction. The as-synthesized nanoparticles were characterized by x-ray differaction (XRD), transimition electron microscope (TEM) and superconducting quantum interference device (SQUID). The nanoparticles are spherical in shape, have bcc structure with the mean particle diameter of 41 nm, and are basically ferromagnetic with a slight amount of superparamagnetic part. The saturation magnetization and coercivity of the nanoparticles at 4.2 K are 190.15 emu/g and 1280 Oe, respectively. The blocking temperature is 250 K in 100 Oe and decreases with increasing the magnetic field.
Preparation of FeCo-based amorphous alloys with excellent soft magnetism and high glass transition temperature

Li Zaidao,Tang Zhaowei,Song Yujun,Zhang Tao

DOI: https://doi.org/10.3969/j.issn.2095-2783.2013.02.012

2013-01-01

Abstract:CoFe-based alloy ribbons with various Co/Fe ratios and alloy element additions have been prepared through rapidquenching process for CoFe amorphous alloys with excellent soft magnetic properties suitable for high temperature operation. Effects of the atomic ratio of cobalt to iron and the addition of alloy elements on the thermal stability and magnetic properties of CoFe amorphous alloys were investigated in detail.Results indicated that(Fe,Co)84Si6B10 alloys could preserve both high thermal stability and remarkable soft magnetic properties when the Co/Fe atomic ratio ranges from 1:1 to 3:1.Addition of elements with high melting temperature(i.e.,B,Hf and Zr) replacing components with low melting temperature(e.g.,Si,Cu) will improve the thermal stability of the amorphous alloys significantly.Meanwhile,these alloys can still have excellent soft magnetic properties.Finally,CoFe-based amorphous alloys with a glass transition temperature as high as 580℃and excellent soft magnetic properties are addressed after optimizing the Co/Fe ratio and addition of alloy elements.
One-pot synthesis and magnetic properties of hollow Fe<sub>70</sub>Co<sub>30</sub> nanospheres

Jing Huang,Lin He,Yonghua Leng,Wei Zhang,Xingguo Li,Chinping Chen,Ying Liu

DOI: https://doi.org/10.1088/0957-4484/18/41/415603

IF: 3.5

2007-01-01

Nanotechnology

Abstract:Hollow Fe70Co30 nanospheres have been prepared in aqueous solution with KBH4 as the reducing agent and sodium dodecyl sulfonate ( SDS) as the stabilizing agent. The diameter of these spheres is about 100 - 200 nm and the shell thickness is about 15 - 20 nm. By transmission electron microscopy ( TEM) analysis, it was found that these hollow spheres formed via an in situ galvanic replacement reaction between iron nanoparticles and the cobalt cation. These hollow Fe70Co30 spheres exhibit surface plasmon resonance ( SPR) absorption in the ultraviolet - visible spectrum. The magnetic properties of the as- prepared hollow Fe70Co30 nanospheres and of a sample annealed at 573 K were studied. Annealing the product can greatly enhance the saturation magnetization Ms and coercivity H-c.

Preparation of Nanostrured Fe - Co Alloy

Effect of Co Addition on the Phase Structure and Magnetic Properties of Fe-Si-Al Alloys

Preparation and study of Fe–Co–Zr–B nano-soft magnetic alloy

Preparation and application of nano-Ni–Co alloy

Study of Preparation of Cobalt Aluminate by Sol-Gel Process and Electroless Plating

Advances in Preparation Study of Nano Magnetic Material Fe-Co Alloys

Sonochemical synthesis, structural and magnetic properties of air-stable Fe/Co alloy nanoparticles

Crystallization Kinetics of Co-Finemet Amorphous Alloys and Magnetic Properties of Nanocrystalline Powder Cores

Preparation and Properties of Fe-Co-Ni Alloy/co0.5ni0.5fe2o4 Magnetic Composite Nanofibers

Preparation of Sm-Co Alloy by Electrodeposition in DMF Solution

Crystallization kinetics and magnetic properties of Fe 63.5Co10Si13.5B9Cu 1Nb3 nanocrystalline powder cores

Preparation and Microwave-Absorbing Properties of FeCo Alloys by Condensation Reflux Method

Co–Al2O3 nanocomposites powder prepared by electroless plating

Synthesis, Characterization and Electrocatalytic Properties of FeCo Alloy Nanoparticles Supported on Carbon Nanotubes

Study on Supercritical Hydrothermal Synthesis of CoFe2O4 Nanoparticles

Sol-gel preparation and characterization of NiCo and Ni3Fe nanoalloys

Novel Preparation and Physicochemical Characterization of a Nanocrystalline Cobalt Ferrite System

Large-Scale Controlled Synthesis of FeCo Nanocubes and Microcages by Wet Chemistry

Synthesis and Magnetic Properties of FeCo Alloy Nanoparticles by Hydrogen Plasma Metal Reaction

Preparation of FeCo-based amorphous alloys with excellent soft magnetism and high glass transition temperature

One-pot synthesis and magnetic properties of hollow Fe<sub>70</sub>Co<sub>30</sub> nanospheres