Abstract:The 2195 Al-Cu-Li alloy is widely utilized in the aerospace industry due to its lightweight nature and high strength. Consequently, gaining a comprehensive understanding of techniques to enhance its microstructural and mechanical properties is crucial for the consistent production of reliable and high-strength aerospace components. In this investigation, a pristine 2195 industrial ingot was subject to three distinct forging pretreatments: PT1, which involved a direct three upsetting and three stretching (3U3S) process; PT2, which combined double stage homogenization (DH) with 3U3S; and PT3, which involved DH along with six upsetting and six stretching (6U6S). Subsequent warm deformation and T8 aging treatment were applied to the pretreated forgings. The microstructure evolution during the processes and the final mechanical properties in three orthogonal dimensions were examined. The findings revealed that the combination of DH and multi-dimensional forging (MDF) facilitated the dissolution of non-equilibrium phases to a greater extent. Consequently, the main strengthening phase transformed from the T 1 + δ` phase observed in PT1 to the denser T1 + little θ` phase observed in PT2 and PT3 after T8 aging treatment. Notably, the tensile strength and yield strength of PT2 and PT3 specimens increased by 20-30 MPa in all three directions. Moreover, the MDF process accelerated the recrystallization behavior from PT1 to PT3, resulting in a gradual reduction in the average grain size of the pretreated samples from 356 μm to 186 μm. Following warm forging and T8 aging, the grains exhibited a finer and equiaxed structure. Additionally, the coarse phase was identified as the primary source of transgranular cracking. The coarse phases within the matrix became more homogeneous and finer from PT1 to PT3, with a gradual decrease in their area fraction. On the fracture surfaces, the aggregation of coarse phases diminished. Consequently, the elongation in the z-direction improved, and the elongation anisotropy and standard deviation decreased in all three directions for PT3 specimens. The findings presented in this study provide valuable insights into the high-performance manufacturing of Al-Cu-Li alloys.

Effect of warm pre-straining on fracture behavior of intermetallic alloy TiAl

Influence of Residual Compressive Stress on Warm Prestress Toughening of HSLA Steel

Mechanism of Effects of Warm Prestressing on Apparent Toughness of Precracked Specimens of Hsla Steels

Fracture Behaviour of Precracked Specimens of a TiAl Alloy

Effect of post-weld heat treatment on microstructure and fracture toughness of 30CrMnSiNi2A steel welded joints

Effect of Prestrain on Microstructure and Mechanical Behavior of Aged Ti–10V–2Fe–3Al Alloy

Mechanism of effects of warm prestressing(WPS) on apparent toughness of notched steel specimens: Part I: Experimental

Effect of forging pretreatment on the microstructures and mechanical properties of the Al-Cu-Li alloy

Effect of softening of 6082-T6 aluminum alloy CMT welded joints on mechanical properties and fracture behavior

Improved Fracture Toughness of Polycrystalline Γ‐tial‐based Intermetallic Alloys with a Favorable Deformation Mechanism of Twinning

Investigation on Cracking Behavior and Development of a Fracture Model of Ti-47Al-2Nb-2Cr Alloy During Hot Deformation

Microstructural morphology effects on fracture toughness and crack growth behaviors in a high strength titanium alloy

Effect of Heating Process on Fracture Behaviors of Wf/Cu82Al10Fe4Ni4 Composites

In Situ Tensile Observation of the Effect of Annealing on Fracture Behavior of Laser Additive Manufactured Titanium Alloy

Toughening Mechanisms of Γ-Tial Alloys and Improvement Methods

Study of tensile properties and fracture mechanisms of fully lamellar TiAl based alloy

Effect of Microstructures on Hot Compression Behavior of a Ti-43Al-2Si Alloy Fabricated by Cold Crucible Continuous Casting

Effect of Thermal Stresses on the Microstructure of the Continuous Cooling TiAl Alloys

Investigation of Compressive and Damage Mechanisms in Fully Lamellar TiAl-Based Alloy

Microstructure evolution and fracture behavior of Ti-5Al-3Mo-3V-2Zr-2Cr-1Nb-1Fe alloy during BASCA heat treatments

Stable strain hardening behavior of Ti-4Al-5Mo-5V-5Cr-1Nb alloy during plastic deformation