Abstract:The surface preparation is a prerequisite for ensuring the required properties of a diamond film formed by gas-phase deposition. The influence of the temperature and concentration of the CuSO 4 etchant on the structural and phase compositions of the surface of hard-alloy materials is considered in this work, and the structural and phase compositions of a continuous polycrystalline diamond film at its growth stages is also considered. The adhesion of the diamond films to the surface of hard-alloy materials is determined qualitatively. It is established that the treatment of the hard-alloy surface in the CuSO 4 solution at t = 23°C leads to the inhomogeneous removal of a cobalt binder with chipping WC grains and the formation of the porous structure in the surface layer of the WC–6% Co alloy. The treatment by the CuSO 4 etchant at t = –2°C provides the homogeneous etching of the Co binder over the boundaries of WC grains and the formation of a chemically homogeneous surface. The orientation growth and adhesion of the diamond film depend on the elemental composition of the WC–Co alloy surface after treatment by the CuSO 4 solution. If the treatment was performed at t sln = 23°C, then the removal of copper from the defect surface WC layer is complicated during the synthesis, which provides the multidirectional growth of diamond crystals in the film along two directions, 〈111〉 and 〈110〉, which causes critical biaxial compressive stresses (2.5 GPa) and leads to low film adhesion to the hard alloy surface. If the treatment is performed at t sln = –2°C, then the orientational growth of diamond crystals in the film occurs in one preferential crystallographic direction 〈111〉, which lowers the biaxial compressive stresses (1.7 GPa) and increases the adhesive bond of the film to the hard alloy surface. The structure imperfection calculated from the ratio of the lines of integrated intensities I 1333 / I 1580 using the Raman spectroscopy method decreases with an increase in concentration at negative temperatures and increases at positive temperatures of the CuSO 4 solution during surface preparation.

Effect of Cobalt-Etched Treatment on the Adhesion between Diamond Films and WC-Co Cemented Carbide

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Study On The Properties Of Diamond Films On Cemented Carbide Substrates By Surface Implantation Pretreatment Process

Interface characteristics of CVD diamond coating on WC-Co cemented carbide substrate

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Effect of Ta diffusion layer on the adhesion properties of diamond coating on WC-Co substrate

Interfacial characterization of diamond thin film coated cemented carbide tool

Mo 2 C interface layer: effect on the interface strength and cutting performance of diamond/Fe-Ni-WC composites

Preparation, wear resistance, and impact toughness of homoepitaxial diamond film deposited on polycrystalline diamond compact by HFCVD method

A competitive-adsorption chemical vapor deposition method: Diamond coated on WC-Co substrate without acid-alkali pretreatment by adding graphene oxide particles

Features of the diamond films growth on the tungsten carbide surface by a copper underlayer

Advances in deposition of diamond films on cemented carbide and progress of diamond coated cutting tools

SiC Interlayer/diamond Coatings Prepared on Cemented Carbide Micro-Tools by High Current DC Extended Arc Chemical Vapor Deposition

The Application of Surface Response Methodology to the Pretreatment of WC Substrates Prior to Diamond Coating

Growth Features of Diamond Films on the Tungsten Carbide Surface with a Copper Sublayer

Growth and characterization of chemical vapor deposition diamond coating incorporated amorphous carbon with high Raman bands induced by CuO particles

Improvement in the universality of high-performance CVD diamond coatings on different WC-Co substrates by introducing multilayered diamond/β-SiC composite

Adhesion, bonding and tensile properties of Ti doped WC (001)/diamond (111) interface: A first-principles calculation

Promising WC-30WB-10Co Cemented Carbide Coating with Improved Density and Hardness Deposited by High Velocity Oxy-Fuel Spraying: Microstructure and Mechanical Properties

Microstructure and properties of ultrafine WC–Co–VC cemented carbides with different Co contents

Preparation of Ti-coated diamond/WC-Co-based cemented carbide composites by microwave-evaporation titanium-plating of diamond particles and microwave hot-press sintering