Hydrothermally Synthesized CeO2 Nanowires for H2S Sensing at Room Temperature

Zhijie Li,Xinyue Niu,Zhijie Lin,Ningning Wang,Huahai Shen,Wei Liu,Kai Sun,Yong Qing Fu,Zhiguo Wang

DOI: https://doi.org/10.1016/j.jallcom.2016.04.311

IF: 6.2

2016-01-01

Journal of Alloys and Compounds

Abstract:The title nanowires are hydrothermally synthesized from aqueous mixtures of Ce(NO3)3, urea, and NaOH (autoclave, 100 °C, 24 h).

What problem does this paper attempt to address?

ChemInform Abstract: Hydrothermally Synthesized CeO2Nanowires for H2S Sensing at Room Temperature.

Zhijie Li,Xinyue Niu,Zhijie Lin,Ningning Wang,Huahai Shen,Wei Liu,Kai Sun,Yongqing Fu,Zhiguo Wang

DOI: https://doi.org/10.1002/chin.201635165

2016-01-01

ChemInform

Abstract:The title nanowires are hydrothermally synthesized from aqueous mixtures of Ce(NO 3 ) 3 , urea, and NaOH (autoclave, 100 °C, 24 h).
Sensitive H2 Gas Sensors Based on SnO2 Nanowires

Sihang Lu,Yuzhu Zhang,Jingyao Liu,Hua-Yao Li,Zhixiang Hu,Xie Luo,Naibo Gao,Bao Zhang,Jianjun Jiang,Aihua Zhong,Jingting Luo,Huan Liu

DOI: https://doi.org/10.1016/j.snb.2021.130334

2021-01-01

Abstract:Sensitive H-2 gas sensors are highly desirable for the prediction and early-warning of H-2 leakage. Low-dimensional nanostructures of metal oxide semiconductor emerge as promising materials candidates, but it remains a challenge to preserve the nanostructures in the real sensors. In this work, we demonstrated highly sensitive H-2 gas sensors based on porous network of SnO2 nanowires that exhibited ultrasmall diameter similar to 2 nm. Colloidal SnO2 nanowires synthesized via a solvothermal process were drop-coated onto the commercial alumina substrates, followed by in-situ annealing treatment at 350 degrees C to remove the surface ligands. The sensors exhibited sensitive response with linear dependence on the H-2 gas concentration ranging from 2 ppm to 100 ppm when operated at 250 degrees C. Typically, the sensor had a response of 13 toward 40 ppm of H-2, with the response and recovery time being 15 s and 31 s, respectively. To further improve the sensor performance, Palladium doped SnO2 nanowires were thoroughly investigated. It's shown that, the operating temperature of the sensor decreased from 250 degrees C to 150 degrees C after Pd doping, and the response and recovery time decreased to 6 s/3 s. The superb sensitivity was attributed to the enhanced gas reception, electron transport as well as utility factor owing to the network nanostructure of ultrathin SnO2 nanowires and catalytic activity of Pd, according to theoretical calculation and adsorption kinetics studies. Combined with the excellent solution processability, the colloidal SnO2 nanowires are potentially attractive for next-generation gas sensors with lower power consumption and integration with silicon-based substrates.
Hydrothermally synthesized MXene Ti3C2/Zn2SnO4 based nanocomposite for H2S sensing at room temperature

Ali Akhtar,Cheng Yao,Rujun Zhou,Shama Sadaf,Mingming Han,Qiang Ling,Si Luo,Daru Chen

DOI: https://doi.org/10.1016/j.ceramint.2024.01.134

IF: 5.532

2024-04-01

Ceramics International

Abstract:Hydrogen sulfide (H2S) gas sensors with high response and minimum limit of detection at room temperature are of great importance to ensure the safety of humans and the environment. A series of samples such as MXene Ti3C2, Ti3AlC2, WS2, MoSe2/Zn2SnO4 and spherical Zn2SnO4 nanoparticles were synthesized via hydrothermal method in this paper. Different characterizations were performed on these samples to check crystal structures, morphologies, chemical states, etc. And gas sensing properties were also performed and analyzed deeply. A series of sensor sheets were fabricated via the spin coating method based on synthesized samples for gas sensing properties. MXene Ti3C2/Zn2SnO4-5 based gas sensor detected the highest response (110) towards 8 ppm H2S with excellent selectivity, the minimum limit of detection (0.01 ppm), mediate long-term stability and good reproducibility compared with other fabricated sensors at room temperature. Also, the sensor response was increased with the increase of H2S concentration. Experimental results showed that the highest response of Ti3C2/Zn2SnO4-5 based gas sensor was accredited to heterojunction, higher BET surface area, and increased oxygen species. The simple way synthesized nanocomposite and fabricated sensors throw a novel idea for tracing H2S at the lowest concentration to prevent different diseases.

materials science, ceramics
QCM-based Humidity Sensor and Sensing Properties Employing Colloidal SnO2 Nanowires

Naibo Gao,Hua-Yao Li,Wenhui Zhang,Yuzhu Zhang,Yi Zeng,Zhixiang Hu,Jingyao Liu,Jianjun Jiang,Ling Miao,Fei Yi,Huan Liu

DOI: https://doi.org/10.1016/j.snb.2019.05.009

IF: 9.221

2019-01-01

Sensors and Actuators B Chemical

Abstract:In this paper, a quartz crystal microbalance (QCM)-based humidity sensor has been fabricated by colloidal fin oxide (SnO2) nanowires. The SnO2 nanowires were synthesized via a colloidal process that employing SnCl4 ethanol solutions mixed with oleic acid (OA) and oleylamine (OLA). The spin-coating method was chosen to deposit the sensitive film at room temperature without high-temperature sintering. Furthermore, the Cu(NO3)(2) methanol solution was used to remove the organic long chains coated on the surface of the colloidal SnO2 nanowires and expose more adsorption sites. The characterizations of the material were studied by means of FTIR, XRD, and FE-SEM. The saturated salt solution method was used to investigate the humidity sensing performance (response, recovery, repeatability, etc.) of the QCM sensor in the range of 11%-97%. The results showed that the sample with 12 h synthesis has the best humidity response. This may be attributed to the larger specific surface area which makes the material provide more adsorption sites for water molecules, and more (110) planes formed which could absorb more water molecules proved by the Density Functional Theory (DFT) calculation.
Room-Temperature High-Performance H2S Sensor Based on Porous CuO Nanosheets Prepared by Hydrothermal Method.

Zhijie Li,Ningning Wang,Zhijie Lin,Junqiang Wang,Wei Liu,Kai Sun,Yong Qing Fu,Zhiguo Wang

DOI: https://doi.org/10.1021/acsami.6b02893

IF: 9.5

2016-01-01

ACS Applied Materials & Interfaces

Abstract:Porous CuO nanosheets were prepared on alumina tubes using a facile hydrothermal method, and their morphology, microstructure, and gas-sensing properties were investigated. The monoclinic CuO nanosheets had an average thickness of 62.5 nm and were embedded with numerous holes with diameters ranging from 5 to 17 nm. The porous CuO nanosheets were used to fabricate gas sensors to detect hydrogen sulfide (H2S) operating at room temperature. The sensor showed a good response sensitivity of 1.25 with respond/recovery times of 234 and 76 s, respectively, when tested with the H2S concentrations as low as 10 ppb. It also showed a remarkably high selectivity to the H2S, but only minor responses to other gases such as SO2, NO, NO2, H2, CO, and C2H5OH. The working principle of the porous CuO nanosheet based sensor to detect the H2S was identified to be the phase transition from semiconducting CuO to a metallic conducting CuS.
Facile Synthesis of Α-Fe2o3/zno Core-Shell Nanowires for Enhanced H2S Sensing

Jia-He Yang,Kai-Ping Yuan,Li-Yuan Zhu,Cheng-Zhou Hang,Xiao-Xi Li,Jia-Jia Tao,Hong-Ping Ma,An-Quan Jiang,Hong-Liang Lu

DOI: https://doi.org/10.1016/j.snb.2019.127617

2020-01-01

Abstract:The alpha-Fe2O3/ZnO core-shell nanowires (NWs) on micro-electro-mechanical system structure were prepared for hydrogen sulfide (H2S) gas sensing. Core alpha-Fe2O3 NWs were prepared by thermal oxidation and the ZnO shell layer was coated by atomic layer deposition, respectively. The diameter of the obtained alpha-Fe2O3/ZnO core-shell NWs increases uniformly with the increase of ZnO shell thickness. When the operating temperature is 250 degrees C, the maximum response of the alpha-Fe2O3/ZnO core-shell NWs gas sensor to 5 ppm H2S is 5.98, which is about five times of pure alpha-Fe2O3 NWs gas sensor (similar to 1.1). Moreover, alpha-Fe2O3/ZnO core-shell NWs-based gas sensors showed good selectivity, response, and recovery properties to H2S. The improvement of gas response of core-shell NWs is due to the slender alpha-Fe2O3/ZnO core-shell NWs and the appropriate energy band structure between ZnO and alpha-Fe2O3. Thus, the proposed alpha-Fe2O3/ZnO core-shell NWs will be one of ideal sensitive materials for H2S high-performance sensor.
Hydrothermal synthesis of hierarchically flower-like CuO nanostructures with porous nanosheets for excellent H2S sensing

Zhijie Li,Junqiang Wang,Ningning Wang,Shengnan Yan,Wei Liu,Yong Qing Fu,Zhiguo Wang

DOI: https://doi.org/10.1016/j.jallcom.2017.07.218

IF: 6.2

2017-01-01

Journal of Alloys and Compounds

Abstract:Flower-like CuO nanostructures with porous nanosheets were synthesized on alumina tube using a hydrothermal method without using any surfactant. The flower-like CuO was comprised of interconnected nanosheets with a uniform thickness of 60 nm. These nanosheets had numerous nanoscale pores with diameters ranging from 20 nm to 160 nm. The copper complex ions of [Cu(NH3)(4)](2+) and NH3 were identified to be critical for the formation of these flower-like CuO nanostructures with porous nanosheets during the hydrothermal process. Gas sensor to hydrogen sulfide (H2S) based on these porous flower-like CuO nanostructures exhibited high sensitivity, good reproducibility and long-term sensing stability when tested at room temperature of 25 degrees C. The gas sensor also showed a remarkably high sensing selectivity to the H2S gas. The gas sensing mechanism was investigated, and the formation of CuS on the surface of CuO nanostructure was identified to be critical for H2S sensing. (C) 2017 Elsevier B.V. All rights reserved.
Binder-Free Ceo2 Coated/Pd-Decorated Cuxo Nanowires Based on Cu Foam for Humidity-Independent Enhanced H2s Gas Sensing

Wenhu Tan,Xinhua Li,Fanyu Xu,Dingchao Wang,Jiaqi Geng,Cheng Zhang,Junhong Hu,Xintang Huang,Benwei Zhang,Xujun Chen

DOI: https://doi.org/10.1016/j.snb.2022.133040

IF: 9.221

2022-01-01

Sensors and Actuators B Chemical

Abstract:Binder-free CeO2 coated/Pd-decorated CuxO nanowires (CuxO/Pd/CeO2_NWs) based on Cu foam were synthe-sized using a four-step process: electrochemical nanoengineering for preparing Cu nanowires, galvanic replacement between Cu nanowires and H2PdCl4, soaking in cerous nitrate solution and followed thermal annealing. Due to the optimized Pd thin layer, followed coating of the moisture-blocking CeO2 overlayer, the binder-free Pd-decorated CuxO nanowires exhibit a prominently enhanced sensing properties to H2S. The CuxO/ Pd/CeO2_NWs sensor exhibits a high response of 36.69 to 50 ppm H2S with rapid response/recovery speed (48.9 s/59.1 s), good selectivity and humidity-independent sensing properties at room temperature. Therefore, this work shows promising potential in detecting H2S and a new insight is opened up in designing binder-free devices based on metal substrate for indoor/outdoor environmental monitoring regardless of humidity fluctuations.
The preparation of MOFs-derived ZnO/Co3O4 nanocages and its sensing performance to H2S

Han Liu,Jiawei Kong,Zhe Dong,Yongmei Zhao,Bao-Li An,Junping Dong,Jiaqiang Xu,Xiaohong Wang

DOI: https://doi.org/10.1039/d3cp02310a

IF: 3.3

2023-06-21

Physical Chemistry Chemical Physics

Abstract:We report one kind of Micro-Electro-Mechanical system (MEMS) H2S gas sensors with excellent sensing performance on ppb level (the lowest detection limit is 5 ppb). The sensors were fabricated with ZnO/Co3O4 sensing materials derived from Zn/Co-ZIF by annealing at a suitable temperature 500°C. ZnO/Co3O4-500 exhibits the highest response when exposed to 10 ppb H2S gas at 120°C, and the response/recovery times are 10 s/21 s. What's more, it exhibits outstanding selectivity, long-terms stability (kept 95% response after 45 days), and moisture resistance (had only a minor fluctuation of 2% even at the 90 RH%). This can be ascribed the reason that ZnO/Co3O4-500 has regular morphology, abundant oxygen vacancies (52.8%) and high specific surface area (96.5 m2/g). This work provided not only a high performance H2S MEMS gas sensor but also a systematical study of the effect of the annealing temperature on sensing performance of ZnO/Co3O4 sensing materials derived from bimetal organic frameworks.

chemistry, physical,physics, atomic, molecular & chemical
Nanostructured Ce/CeO2-rGO: Highly Sensitive and Selective Electrochemical Hydrogen Sulfide (H2S) Sensor

Shivsharan M. Mali,Shankar S. Narwade,Balaji B. Mulik,Vijay S. Sapner,Shubham J. Annadate,Bhaskar R. Sathe,Mali, Shivsharan M.,Narwade, Shankar S.,Mulik, Balaji B.,Sapner, Vijay S.,Annadate, Shubham J.,Sathe, Bhaskar R.

DOI: https://doi.org/10.1007/s12678-023-00839-6

2023-09-15

Electrocatalysis

Abstract:Herein, cerium/cerium oxide nanoparticles have been decorated on reduced graphene oxide (Ce/CeO 2 -rGO) for room temperature electrochemical determination of H 2 S in 0.5 M KOH. There is a superior linear correlation between the peak current density and H 2 S content in the tested range of 1–5 ppm. Moreover, comparison to other abundant gases such as CO 2 shows no response at the potential of H 2 S oxidation, confirming no interference with H 2 S detection. It also reveals that the Ce/CeO 2 -rGO nanocomposite is a highly selective and sensitive system for the determination of H 2 S gas. Ce/CeO 2 -rGO synthesized by a simple chemical approach and further characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR), field emission-scanning electron microscopy (FE-SEM), coupled energy dispersive analysis of X-ray (EDAX), and BET-surface area measurement confirms the porosity of synthesized nanomaterials and homogeneous decoration of Ce/CeO 2 nanoparticles on rGO sheets. The electrochemical studies, i.e., linear sweep voltammetry (LSV), of Ce/CeO 2 -rGO demonstrate the electrochemical H 2 S sensing at room temperature and for lower gas concentration (1 ppm) detection. The sensing mechanism is believed to be based on the modulation of the current and applied potential path across the electron exchange between the cerium oxide and rGO sites when exposed to H 2 S.

chemistry, physical,electrochemistry
High Performance H 2 S Sensor Based on Ordered Fe 2 O 3 /Ti 3 C 2 Nanostructure at Room Temperature

Changkun Qiu,Hao Zhang,Qingrun Li,Yifan Song,Fei An,Haozhi Wang,Shiqiang Wang,Liang Zhu,Dongzhi Zhang,Zhe Yang

DOI: https://doi.org/10.1021/acssensors.4c01691

IF: 8.9

2024-10-25

ACS Sensors

Abstract:The utilization of a heterogeneous nanojunction design has shown significant enhancements in the gas sensing capabilities of traditional metal oxide gas sensors. In this study, a novel room temperature H(2)S gas sensor employing Fe(2)O(3) functionalized Ti(3)C(2) MXene as the sensing material has been developed. This sensor exhibits a broad detection range (0.01-500 ppm), low detection limit (10 ppb), and rapid response/recovery times (10 s/15 s), making it ideal for ppb-level H(2)S detection....

chemistry, multidisciplinary, analytical,nanoscience & nanotechnology
Extremely Sensitive and Accurate H2S Sensor at Room Temperature Fabricated with In-doped Co3O4 Porous Nanosheets

Jie Wu,Ying Yang,Chengxin Zhang,Hui Yu,Licheng Huang,Xiangting Dong,Jinxian Wang,Xinlu Wang

DOI: https://doi.org/10.1039/c9dt01043b

IF: 4

2019-01-01

Dalton Transactions

Abstract:A facile hydrothermal method to prepare In-doped Co3O4 porous nanosheets is reported in this paper for the first time. The prepared samples were made into gas sensors, and their sensing properties, such as response, response time, recovery time, selectivity and stability, have been researched systematically. These results indicate that the sensor fabricated with 1.0 at% In-doped Co3O4 porous nanosheets shows a high response of 6.81 to 50 ppm and an obvious response of 1.4 to 1 ppm H2S. What's more, this sensor exhibited a high selectivity and outstanding long-term stability toward H2S. The excellent gas sensing performance was mainly ascribed to two reasons. (i) Doping with In increases the concentration of charge carriers, oxygen-deficient regions and the chemisorbed oxygen, which enhances the gas response. (ii) The rough porous structure is conducive to gas adsorption and capture, and provides many active sites for the sensing reaction. Therefore, 1.0 at% In-doped Co3O4 porous nanosheets could be used as a sensing material in future applications.
Sensitive detection of H2S based on Ce doped ZnCo2O4 hollow microspheres at low working temperature

Hao-Jun Li,Jia-Ying Huang,Lin-Xuan Li,Rong Chen,Fang Liu,Ling Wu,Zemeng Feng,Yulong Yin,Zhong Cao,Donghong Yu

DOI: https://doi.org/10.1039/d4ay00567h

IF: 3.1

2024-06-16

Analytical Methods

Abstract:In order to develop highly efficient H2S gas sensor at low working temperature, a kind of novel Ce-doped ZnCo2O4 hollow microspheres (Ce/ZnCo2O4 HMS) was successfully synthesized using a template-free one-pot method, that had a sensitive response toward H2S in this paper. The microstructure and morphology of the materials were characterized by using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The gas-sensing performance of the composites was investigated, showing that the ZnCo2O4 doped with 6 mol% Ce had the highest response to 20 ppm H2S at low operating temperature of 160 °C with a response value of 67.42, which was about 2 times higher than that of original ZnCo2O4. The prepared Ce/ZnCo2O4 HMS sensors in response to H2S exhibited a linear range of 0.1 ~ 200 ppm with a low detection limit of 0.1 ppm under the condition of ambient humidity of 45% and ambient temperature of 20 °C. Meanwhile, it also possessed good selectivity, repeatability and reproducibility. The response value of the sensor decreased by 5.32% after 7 months of continuous monitoring of H2S in atmospheric environment of pig farm, indicating that the sensor had a long-term stability and continuous service life with important application prospects.

spectroscopy,chemistry, analytical,food science & technology
High Performance H2S Sensor Based on Ordered Fe2O3/Ti3C2 Nanostructure at Room Temperature

Changkun Qiu,Hao Zhang,Qingrun Li,Yifan Song,Fei An,Haozhi Wang,Shiqiang Wang,Liang Zhu,Dongzhi Zhang,Zhe Yang

DOI: https://doi.org/10.1021/acssensors.4c01691

2024-11-22

Abstract:The utilization of a heterogeneous nanojunction design has shown significant enhancements in the gas sensing capabilities of traditional metal oxide gas sensors. In this study, a novel room temperature H2S gas sensor employing Fe2O3 functionalized Ti3C2 MXene as the sensing material has been developed. This sensor exhibits a broad detection range (0.01-500 ppm), low detection limit (10 ppb), and rapid response/recovery times (10 s/15 s), making it ideal for ppb-level H2S detection. The exceptional gas sensitivity of Fe2O3/Ti3C2 composite to H2S can be attributed to several key factors. First, the unique layered frame structure of Fe2O3/Ti3C2 significantly amplifies the surface area of the hybrid material, enhancing the absorption and diffusion capabilities of H2S molecules. Second, the abundance of functional groups (-O, -OH, and -F) on the surface of Ti3C2 MXene nanosheets provides additional active sites for H2S adsorption, The density functional theory calculation confirms that the adsorption energy of the Fe2O3/Ti3C2 composite for H2S (-2.93 eV) is significantly lower than that of pure Fe2O3 (-2.37 eV) and Ti3C2 (-0.2 eV). Lastly, the remarkable metal conductivity of Ti3C2 MXene ensures efficient electron transfer, thereby enhancing overall sensing performance.
Room temperature H2S sensing properties and mechanism of CeO2–SnO2 sol–gel thin films

Guojia Fang,Zuli Liu,Chuanqing Liu,Kai-lun Yao

DOI: https://doi.org/10.1016/S0925-4005(99)00467-0

2000-01-01

Abstract:Using non-alkoxide SnCl2 . 2H(2)O, Ce(NH4)(2)(NO3)(6) as precursors, room temperature H2S gas sensitive CeO2-SnO2 thin films have been obtained. In this paper, the synthesis process of CeO2-SnO2 thin films has been introduced; the gas sensing properties of the CeO2-SnO2 thin films were investigated and compared with those of SnO2 and ZrO2-SnO2 thin films. The experiments illustrate that CeO2-SnO2 thin film has quite a quick response and recovery behavior, high selectivity, and has better sensitivity than that of ZrO2-SnO2 thin film toward low concentration of H2S at room temperature. The sensing mechanism of CeO2-SnO2 thin films toward H2S at room temperature has also been discussed in this paper. (C) 2000 Elsevier Science S.A. All rights reserved.
Exploiting Free-Standing p-CuO/n-TiO 2 Nanochannels as a Flexible Gas Sensor with High Sensitivity for H 2 S at Room Temperature

Haoxuan He,Chenxi Zhao,Jing Xu,Kuanzhi Qu,Zhen Jiang,Zhida Gao,Yan-Yan Song

DOI: https://doi.org/10.1021/acssensors.1c01256

IF: 8.9

2021-08-31

ACS Sensors

Abstract:Hydrogen sulfide (H2S) is an extremely hazardous gas and is harmful to human health and the environment. Here, we developed a flexible H2S gas-sensing device operated at room temperature (25 °C) based on CuO nanoparticles coated with free-standing TiO2-nanochannel membranes that were prepared by simple electrochemical anodization. Benefiting from the modulated conductivity of the CuO/TiO2 p–n heterojunction and a unique nanochannel architecture, the traditional thermal energy was innovatively replaced with UV irradiation (λ = 365 nm) to provide the required energy for triggering the sensing reactions of H2S. Importantly, upon exposure to H2S, the p–n heterojunction is destroyed and the newly formed ohmic contact forms an antiblocking layer at the interface of CuS and TiO2, thus making the sensing device active at room temperature. The resulting CuO/TiO2 membrane exhibited a notable detection sensitivity for H2S featuring a minimum detection limit of 3.0 ppm, a response value of 46.81% against 100 ppm H2S gas, and a rapid response and recovery time. This sensing membrane also demonstrated excellent durability, long-term stability, and wide-range response to a concentration of up to 400 ppm in the presence of 40% humidity as well as outstanding flexibility and negligible change in electrical measurements under various mechanical stability tests. This study not only provides a new strategy to design a gas sensor but also paves a universal platform for sensitive gas sensing.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acssensors.1c01256.Photographs; SEM images; XPS spectra; UV–vis absorption spectra; EDS spectra; XRD spectra; tables and resistance of TiO2 and CuO/TiO2 under different conditions (PDF)This article has not yet been cited by other publications.

chemistry, multidisciplinary, analytical,nanoscience & nanotechnology
Room Temperature H2s Sensing Properties And Mechanism Of Ceo2-Sno2 Sol-Gel Thin Films

Gj Fang,Zl Liu,Cq Liu,Kl Yao

1998-01-01

Abstract:Using non-alkoxide SnCl2. 2H(2)O, Ce(NH4)(2)(NO3)(6) as precursors, room temperature H2S gas sensing CeO2-SnO2 thin films have been obtained. In this paper, the synthesis process of CeO2-SnO2 thin films has been introduced; the gas sensing properties of the CeO2-SnO2 thin films were investigated and compared with those of SnO2 and ZrO2-SnO2 thin films. The experiments illustrate that CeO2-SnO2 thin film has quite quick response and recovery behaviour, high selectivity and has better sensitivity than that of ZrO2-SnO2 thin film toward low concentration of H2S at room temperature. The sensing mechanism of CeO2-SnO2 thin films toward H2S at room temperature has been also discussed in this paper.
Hydrothermally Processed SnO2 Nanocrystals for Ultrasensitive NO Sensors

Ting Lv,Yuejiao Chen,Jianmin Ma,Libao Chen

DOI: https://doi.org/10.1039/c4ra03121k

IF: 4.036

2014-01-01

RSC Advances

Abstract:SnO2 nanocrystals have been successfully synthesized by a hydrothermal method assisted by biuret. When tested as the gas-sensing material, these hydrothermally processed SnO2 nanocrystals displayed an ultrasensitive response towards NO and ultrahigh selectivity due to their physicochemical nature.
ZnO Nanoparticle-Based MEMS Sensors for H 2 S Detection

Lecheng Zhu,Qian Rong,Zheng Yang,Wei Zhang,Mingzhi Jiao,Jiming Song,Chunchang Wang,Youmin Guo

DOI: https://doi.org/10.1021/acsanm.2c02581

IF: 6.14

2022-08-12

ACS Applied Nano Materials

Abstract:The development of microelectromechanical system (MEMS)-based sensors with ZnO nanoparticles as sensitive materials for detecting a low concentration of H2S has recently attracted extensive attention because of their small size and easy integration. In this study, undecorated ZnO nanoparticles were synthesized by a facile coprecipitation method with the regulation of ammonia water. The phase structure, nanostructure, specific area, surface basicity, and oxygen species of the synthesized ZnO nanoparticles were systematically investigated. Then, preferred ZnO-1 nanoparticles were deposited on the MEMS microhotplate chips as a sensitive material, and the corresponding gas-sensing performances were characterized for various gases at an optimal operating temperature of 220 °C. The MEMS-based sensors with ZnO-1 showed good sensitivity to 1 ppm H2S at 220 °C with response/recovery times of 72 and 29 s, respectively. Furthermore, the sensor presented a wide linear range from 50 ppb to 15 ppm, good repeatability, and high selectivity. Such enhanced sensing performance to H2S was mainly attributed to the large surface area and the high surface basicity of prepared ZnO-1 nanoparticles. Moreover, a plausible reason for the enhanced sensing performance was also proposed.

materials science, multidisciplinary,nanoscience & nanotechnology
Individual Bi2s3 Nanowire-Based Room-Temperature H-2 Sensor

K. Yao,W. W. Gong,Y. F. Hu,X. L. Liang,Q. Chen,L. -M. Peng

DOI: https://doi.org/10.1021/jp8022293

2008-01-01

Abstract:Single Bi2S3 nanowire devices were fabricated using the focused ion beam technique to deposit Pt electrodes. Repeatable and reliable ohmic contacts were obtained. The devices exhibit outstanding H-2 sensing performance that can detect H2 (in N-2) at room temperature with a sensitivity of 22% at 10 ppm (corresponds to 4.0 x 10(-7) mol/L). Decorating Pd nanoparticles on the surface of the nanowire does not improve the sensing performance, contrary to most of the existing nanowire (or nanotube) H-2 sensors. The sensing mechanism of Bi2S3 nanowire devices is found to be different from that of other sensors based on nanowires or nanotubes. Experiments on different H-2 concentrations and gas pressures suggest that the sensing response is determined mainly by the amount of H-2 molecules instead of the proportion of H-2 in the mixed gas.

Hydrothermally Synthesized CeO2 Nanowires for H2S Sensing at Room Temperature

ChemInform Abstract: Hydrothermally Synthesized CeO2Nanowires for H2S Sensing at Room Temperature.

Sensitive H2 Gas Sensors Based on SnO2 Nanowires

Hydrothermally synthesized MXene Ti3C2/Zn2SnO4 based nanocomposite for H2S sensing at room temperature

QCM-based Humidity Sensor and Sensing Properties Employing Colloidal SnO2 Nanowires

Room-Temperature High-Performance H2S Sensor Based on Porous CuO Nanosheets Prepared by Hydrothermal Method.

Facile Synthesis of Α-Fe2o3/zno Core-Shell Nanowires for Enhanced H2S Sensing

Hydrothermal synthesis of hierarchically flower-like CuO nanostructures with porous nanosheets for excellent H2S sensing

Binder-Free Ceo2 Coated/Pd-Decorated Cuxo Nanowires Based on Cu Foam for Humidity-Independent Enhanced H2s Gas Sensing

The preparation of MOFs-derived ZnO/Co3O4 nanocages and its sensing performance to H2S

Nanostructured Ce/CeO2-rGO: Highly Sensitive and Selective Electrochemical Hydrogen Sulfide (H2S) Sensor

High Performance H 2 S Sensor Based on Ordered Fe 2 O 3 /Ti 3 C 2 Nanostructure at Room Temperature

Extremely Sensitive and Accurate H2S Sensor at Room Temperature Fabricated with In-doped Co3O4 Porous Nanosheets

Sensitive detection of H2S based on Ce doped ZnCo2O4 hollow microspheres at low working temperature

High Performance H2S Sensor Based on Ordered Fe2O3/Ti3C2 Nanostructure at Room Temperature

Room temperature H2S sensing properties and mechanism of CeO2–SnO2 sol–gel thin films

Exploiting Free-Standing p-CuO/n-TiO 2 Nanochannels as a Flexible Gas Sensor with High Sensitivity for H 2 S at Room Temperature

Room Temperature H2s Sensing Properties And Mechanism Of Ceo2-Sno2 Sol-Gel Thin Films

Hydrothermally Processed SnO2 Nanocrystals for Ultrasensitive NO Sensors

ZnO Nanoparticle-Based MEMS Sensors for H 2 S Detection

Individual Bi2s3 Nanowire-Based Room-Temperature H-2 Sensor