Abstract:The adsorption and desorption process of selenium (Se) clusters, especially small molecule Se3 and Se4, on graphite enhance the diffusion and reaction activity of traditional Se particles, thereby improving the chemical environment for grain growth, optimizing the film crystallinity, and passivating defects, and finally making the device efficiency up to 14.5% with a VOC of 553.1 mV. Insufficient selenization and uneven distribution of elements caused by the poor diffusion and reaction activity of selenium clusters is one of the main issues limiting the efficiency of Cu2ZnSn(S,Se)4 (CZTSSe) solar cells. Here, this work designs a simple and feasible strategy to improve the activity of selenium (Se) by implementing high‐temperature treatment on graphite boxes loaded with Se pellets. The rapid adsorption/desorption characteristics of graphite on active gaseous small‐molecule selenium have successfully introduced hyperactive Se4, Se3, and Se2 into the selenization process. The results indicate that the adsorbed non‐toxic gaseous active Se3 and Se4 can quickly and uniformly diffuse into the precursor film at low temperatures, thereby inducing nucleation and grain growth at both surface and back interface simultaneously, which inhibits the upward migration and aggregation of cations, especially Cu, and promotes the homogenization of elements. The overall relatively Cu‐poor chemical environment suppresses the formation of CuZn defects and [2CuZn+SnZn] defect clusters, and also promotes the generation of favorable VCu. The band tail states and non‐radiative recombination are then optimized. Finally, the CZTSSe solar cells achieve a power conversion efficiency (PCE) of 14.5%, with VOC/VOCSQ of 67% being one of the highest in the literature.

Impact of Sequential Annealing Step on the Performance of Cu2ZnSn(S,Se)4 Thin Film Solar Cells

Formation of Alloyed Cu2Cox Zn1-x Sn(S,Se)4 Absorption Layer and Its Application in Solar Cells

Formation of Alloyed Cu2CoxZn1-xSn(S,Se)4 Absorption Layer and Its Application in Solar Cells.

Preparing Cu2ZnSnSe4 thin film solar cells based on selenium containing precursors

Exploring the optimal two-step selenization process to enhance the performance of ionic liquid solution based Cu2ZnSn(S,Se)4 thin film solar cells

Benign Solutions and Innovative Sequential Annealing Processes for High Performance Cu2ZnSn(Se,S)4 Photovoltaics

Improving the Performance of Solution-Based CZTSSe Absorber by Selenization Annealing with Selenium Powder in Argon

Influence Of Annealing Conditions On The Structure And Compositions Of Electrodeposited Cuinse2 Films

An Investigation on Phase Transition for As-Sputtered Cu2ZnSnSe4 Absorbers During Selenization

Passivation of Deep‐Level Defects through Chemical Environment Regulation for Efficient CZTSSe Solar Cells Based on Active Selenium Adsorption–Desorption Process

Compositional Dependence of Structural and Electronic Properties of Cu2ZnSn(S,Se)4alloys for Thin Film Solar Cells

Thin-Film Solar Cells Based on Selenized CuSbS2 Absorber

An Efficient S and Se Co-Annealing Strategy for Performance Enhancement of Solution-Processed Submicron CuIn(S,Se)2 Solar Cells

Phase composition of the earth-abundant Cu2SnS3 thin films with different annealing temperature and its effects on the performance of the related solar cells

Enhanced solar cell performance of Cu 2 ZnSnSe 4 thin films through structural control by using selenide stacked nanolayers in a non-toxic selenium atmosphere

Preparation and characterization of Cu2ZnSnSe4 thin films by selenization of electrodeposited metal precursors

Improved Performance of Electroplated CZTS Thin-Film Solar Cells with Bifacial Configuration

Significantly Improving the Crystal Growth of a Cu 2 ZnSn(S,Se) 4 Absorber Layer by Air-Annealing a Cu 2 ZnSnS 4 Precursor Thin Film

Achieving 11.95% Efficient Cu2ZnSnSe4 Solar Cells Fabricated by Sputtering a Cu-Zn-Sn-Se Quaternary Compound Target with a Selenization Process

Effects of Annealing on CuInGaSe2 Solar Cell Prepared by Magnetron Sputtering

The Effects of Selenium Content on Cu(Inga)Se-2 Thin Film Solar Cells by Sputtering from Quaternary Target with Se-Free Post Annealing