Abstract:<math>{101¯2}</math> twins were introduced into the magnesium (Mg) plate AZ31 via pre-rolling along its transverse direction. The plates, both with and without the pre-induced <math>{101¯2}</math> twins, were subjected to uniaxial tension along different directions. Using crystal plasticity modeling, we found that the strengthening effect of the pre-induced <math>{101¯2}</math> twins on the macroscopic flow stress primarily arised from the increased slip resistance caused by the boundaries, rather than the orientation hardening due to the twinning reorientation (although the latter did make its contribution in some specific loading directions). Besides, the pre-existing <math>{101¯2}</math> twins were found, by both experiments and simulation, to promote the activity of prismatic 〈a〉 and pyramidal 〈c + a〉 in the parent matrix of the material. Further analysis showed that the enhanced non-basal slip activity is related to the <math>{101¯2}</math> twin boundaries' low micro Hall-Petch slope ratios of non-basal slips to basal slip. With the critical resolved shear stress (CRSS) obtained from crystal plasticity modeling and the orientation data from EBSD, a probability-based slip transfer model was proposed. The model predicts higher slip transfer probabilities and thus lower strain concentration tendencies at <math>{101¯2}</math> twin boundaries than that at grain boundaries, which agrees with the experimental observation that the strain localization was primarily associated with the latter. The present findings are helpful scientifically, in deepening our understanding of how the pre-induced <math>{101¯2}</math> twins affect the strength and slip activity of Mg alloys, and technologically, in guiding the design of the pre-strain protocol of Mg alloys.

Influence of Basal Slip Activity in Twin Lamellae on Mechanical Behavior of Mg Alloys

On the strengthening and slip activity of Mg-3Al-1Zn alloy with pre-induced { 10 1 ̄ 2 } twins

Influence of In-Plane Simple Shear Strain on the Grain Orientation Regulation and Stretch Formability of Pre-twinned AZ31 Magnesium Alloy Sheet

Effect of pre-deformation on the activation stress of {10–12} twinning in Mg–3Al–1Zn alloy

Achieving excellent ductility with increased Schmid Factor but decreased direct strain contribution of basal slip in an intergranular misorientation tailored magnesium alloy

Study on the Twinning/De-twining Behavior of Different Types of Twin–Twin Interaction via Experiments and Molecular Dynamics Simulation

Twinning Behavior of a Strongly Basal Textured AZ31 Mg Alloy During Warm Rolling

A quantitative study on mechanical behavior of Mg alloys with bimodal texture components

Deformation mechanisms of basal slip, twinning and non-basal slips in Mg–Y alloy by micropillar compression

In-situ Analysis of Microscopic Plastic and Failure Behaviors of Extruded Magnesium Alloy

Quantitative Investigation on the Slip/Twinning Activity and Cracking Behavior During Low-Cycle Fatigue of an Extruded Mg-3Y Sheet

The Dislocation-Twin Interaction and Evolution of Twin Boundary in AZ31 Mg Alloy

Mg-3Al-1Zn alloy deformed along different strain paths: Role of latent hardening

In-situ and ex-situ investigation of deformation behaviors of a dual-phase Mg−Ni−Y alloy

Anomalous Hardening in Magnesium Driven by a Size-Dependent Transition in Deformation Modes

Research on deformation mechanism of AZ31 magnesium alloy during uniaxial compression

Effect of Pre-Existing Twinning on Strain Localization During Deformation of a Magnesium Alloy

Evolution of deformation mechanisms and their orientation dependence in fine-grained Mg-3Gd during tension

An Investigation of Slip and Twinning Behavior of a Zirconium Alloy During Plastic Deformation Based on In-Situ SEM-EBSD

The effects of orientation control via tension-compression on microstructural evolution and mechanical behavior of AZ31 Mg alloy sheet

Effect of Slip on Detwinning Behavior During Multi-Direction Compression of A Wrought Magnesium Alloy