An Ultra-Compact Colorless 50:50 Coupler Based on Phc-Like Metamaterial Structure

Luluzi Lu,Minming Zhang,Feiya Zhou,Deming Liu

DOI: https://doi.org/10.1364/ofc.2016.tu3e.5

2016-01-01

Abstract:A novel PhC-like metamaterial structure with low fabricating accuracy requirements is proposed. We design and fabricate a 2.6μm×2.6μm coupler employing such structure. The measured excess loss of each port is less than 1dB over 60nm.

What problem does this paper attempt to address?

A Multilayer Dual-Band Coupler Based on Composite Right/left-Handed Folded Substrate Integrated Waveguide

Li-Zheng Zhang,Liang Zhou,Wei Jiang,Wen-Yan Yin

DOI: https://doi.org/10.1109/icmmt.2012.6230222

2012-01-01

Abstract:A multilayer dual-band coupler, based on the composite right/left-handed (CRLH) folded substrate integrated waveguide (FSIW) transmission line (TL), is proposed and investigated. The characterization of the CRLH FSIW and the coupling method are performed to realize a 3 dB coupler with compact size. For verification, a dual-band coupler operating at 2.4 GHz/3.8 GHz is designed, fabricated and measured. The simulated and measured results are shown reasonable agreements.
Ultracompact Fiber-to-Chip Metamaterial Edge Coupler

An He,Xuhan Guo,Ting Wang,Yikai Su

DOI: https://doi.org/10.1021/acsphotonics.1c00993

IF: 7

2021-01-01

ACS Photonics

Abstract:Compact fiber-to-chip light coupling with low loss and large bandwidth, SMF-to-chip edge coupler in particular, is extensively demanded in integrated photonics. The inescapable challenge of edge coupler is the difficulty and complexity in fabrication and packaging. During the past decades, metamaterials have manifested marvelous talent in integrated photonics. Here, we experimentally demonstrate an ultracompact edge coupler via metamaterial for SMF with a mode field diameter of 10 mu m, which is fully based on silicon-on-insulator material and a CMOS compatible fabrication process. In this work, we theoretically analyze the coupling performance and the fabrication difficulty. The experimental results show that this metamaterial-based coupler possesses low coupling loss and broad bandwidth simultaneously with the coupling length of only 90 mu m. At 1550 nm, the coupling losses are 2.22/2.53 dB/facet for the fundamental TE/TM mode, while the minimum average loss could reach 1.81 dB/facet. The measured bandwidth with a loss below 3 dB is as broad as 120 nm, covering the entire C/L band. Moreover, this prominently eased fabrication process potentially exhibits significant superiority in both research and industrial applications.
High-efficiency Grating Coupler Based on Fast Directional Optimization and Robust Layout Strategy in 130 Nm CMOS Process.

Xiangyu Luo,Guangcan Mi,Yanbo Li,Tao Chu

DOI: https://doi.org/10.1364/ol.452054

IF: 3.6

2022-01-01

Optics Letters

Abstract:We experimentally demonstrated a high-efficiency grating coupler by combining an interleaved etch and apodized structure for fiber-to-chip coupling. The grating coupler was optimized using the fast directional optimization method to achieve apodization. The grating coupler utilized a layout strategy involving an extended mask to avoid alignment errors for a multi-etch structure. The coupling efficiency was measured to be -2.2 dB at a wavelength of 1549 nm with a 3 dB bandwidth of 47 nm. The grating coupler, having no gold reflector, subwavelength index matching structure, or additional material layers, was fabricated using a commercial silicon photonics process with a minimum feature size of 140 nm. This grating coupler design provides a robust and effective coupling scheme and the proposed method can be employed to adopt the design in accordance with standard foundry design rules.
Compact and efficient coupler to interface hybrid dielectric-loaded plasmonic waveguide with silicon photonic slab waveguide

rakesh g mote,hongson chu,ping bai,erping li

DOI: https://doi.org/10.1016/j.optcom.2012.04.037

IF: 2.4

2012-01-01

Optics Communications

Abstract:A coupler is proposed to interface a hybrid dielectric-loaded plasmonic waveguide (HDLPW) with a silicon photonic slab waveguide. The HDLPW is firstly designed and optimized to attain the best tradeoff between the mode confinement and the propagation distance. The designed coupler is inspired from the taper configuration and numerically modeled through finite-difference time-domain (FDTD) simulation. The results demonstrate that a high confinement and low loss of the energy is achieved from a silicon photonic slab waveguide into the dielectric slot of area 50×200nm2 in the HDLPW. The transmission attained through the coupler with a compact size of 400nm is found to be as high as 80% (1dB). Further, the planar nature of taper configuration makes the coupler easy to fabricate using the state-of-the-art CMOS facilities. The proposed coupler is useful in enabling the integration between photonic and hybrid plasmonic waveguides and thus realizing on-chip hybrid integrated circuits.
Single-step-etched ultra-compact metamaterial grating coupler enabled by a hierarchical inverse design approach

Qiao Wang,Ruiqi Luo,Nan Liu,Maojing Hou,Bo Xiong,Guandong Liu,Wei Ma

DOI: https://doi.org/10.1007/s11433-023-2236-3

2024-01-05

Science China Physics Mechanics and Astronomy

Abstract:With the concept of metamaterials introduced into integrated photonics, subwavelength structures have gained popularity for their ability to create devices with ultra-compact size, high performance, and versatile functionalities. However, traditional metamaterial design methods are usually based on empirical templates and physical approximations, lacking the ability to design free-form metamaterial structures and optimize entire devices globally. In this work, we propose a hierarchical inverse design approach that combines a conventional effective refractive index based metamaterial structures design with a follow-up global topology optimization. The empirical metamaterial grating coupler design based on effective refractive index engineering faces inaccurate index extraction and insufficient approximation of wavevector matching conditions, which deteriorates coupling efficiency, especially for fully-etched devices with the decreased tapering region. Fortunately, a subsequent overall topology optimization step can well compensate for the negative effect of the shrinking device footprint to increase the efficiency of the metamaterial grating coupler. We demonstrate a 23 μm×10 μm ultra-compact metamaterial grating coupler with single-step-etched to couple light between a fiber and a 500 nm single-mode silicon waveguide in the O-band. Experimental measurement shows an insertion loss of 3.17 dB and a 3 dB bandwidth of 77 nm, making it the smallest footprint device ever reported.

physics, multidisciplinary
CMOS-Compatible Ultralow-Loss Three-Step Silicon Edge Coupler with Substrate Substitution in the Whole Communication Band

Zhen Wang,Jin Zhang,Lei Zhang,Xiaoke Ruan,Weijie Tang,Tao Chu

DOI: https://doi.org/10.3390/mi14010066

IF: 3.4

2022-01-01

Micromachines

Abstract:Edge coupler is a key component of silicon-based optoelectronic chips, which dramatically reduces the coupling loss between fibers and transmission waveguides. Here, we propose an ultralow-loss three-step silicon edge coupler based on a 130 nm CMOS process. By replacing the silicon substrate with a material with a lower refractive index than silicon oxide, the silicon leakage loss and polarization-dependent loss can be significantly improved. This structure avoids the existence of a cantilever, which enhances the mechanical strength of the edge coupler. Coupling with standard single-mode fiber, the simulation results demonstrate that the TE/TM mode has an ultralow loss of 0.63/1.08 dB at 1310 nm and 0.57/1.34 dB at 1550 nm, and the 0.5 dB bandwidth covering the entire communication band is about 400 nm. In the entire communication band, the polarization-dependent loss is less than 0.8 dB. Furthermore, we propose a taper shape design method based on mode analysis, which can be adapted for any taper to improve its compactness. Compared with the parabolic shape, the coupling loss of the edge coupler with a length of 460 μm for the TE mode is improved by 0.3 dB on average, this edge coupler provides a feasible solution for fiber-to-chip coupling and is perfectly suitable for wavelength division multiplexing applications in optical communications.
Asymmetric Plasmonic-Dielectric Coupler with Short Coupling Length, High Extinction Ratio, and Low Insertion Loss.

Qiang Li,Yi Song,Gan Zhou,Yikai Su,Min Qiu

DOI: https://doi.org/10.1364/ol.35.003153

IF: 3.6

2010-01-01

Optics Letters

Abstract:Asymmetric directional coupling between a hybrid plasmonic waveguide with subwavelength field confinement and a conventional dielectric waveguide is investigated. The proposed hybrid coupler features short coupling length, high coupling efficiency, high extinction ratio, and low insertion loss; it can also be integrated into a silicon-based platform. This coupler can be potentially adopted for signal routing between plasmonic waveguides and dielectric waveguides in photonic integrated circuits. Furthermore, it can be exploited to efficiently excite hybrid plasmonic modes with conventional dielectric modes.
High-Efficiency Unidirectional Dual-Wavelength-Band Grating Coupler with 1D Subwavelength Structure

Haoyang Tan,Baobao Chen,Yi Zhao,Shiming Gao,Xiaowei Guan

DOI: https://doi.org/10.1109/lpt.2023.3326185

IF: 2.6

2023-01-01

IEEE Photonics Technology Letters

Abstract:A unidirectional dual-wavelength-band grating coupler with one-dimensional (1D) subwavelength structures is proposed and experimentally demonstrated. Inverse optimization method is used for the design and the grating coupler fabricated on the silicon-on-insulator chip can achieve efficient fiber-chip coupling simultaneously in the O-band and the L-band. The peak coupling efficiencies in the two bands are measured to be 19.7% and 19.5% with 3-dB bandwidths of 27 and 38-nm, respectively.
Compact broadband silicon 3 dB coupler based on shortcuts to adiabaticity.

Defen Guo,Tao Chu

DOI: https://doi.org/10.1364/OL.43.004795

IF: 3.6

2018-01-01

Optics Letters

Abstract:We proposed and experimentally demonstrated a compact, broadband, and low-loss-mode-evolution-based 2 x 23 dB coupler on a silicon-on-insulator platform. The waveguide widths and separations of the coupler were tapered in an optimal manner using the shortcuts to the adiabaticity method. The coupler, with a similar to 70 mu m total length and 200 nm feature size, exhibited <0.3 dB measured excess loss over a broadband wavelength range from 1500 to 1600 nm. Balanced and unbalanced Mach-Zehnder interferometers fabricated for validation showed extinction ratios larger than 27 and 23 dB, respectively, over a 100 nm bandwidth. The extracted splitting ratio was between 0.48 and 0.52. (C) 2018 Optical Society of America
Ltra-Compact Silicon Photonic Edge Coupler Based On Subwavelength Gratings

Xin Mu,Sailong Wu,Lirong Chong,Xin Tu,H. Y. Fu

2019-01-01

Abstract:Wc present an ultra -compact fork -shape cdgc coupler based on subwavelength gratings stnicture. This cdgc coupler achieves a high efficiency of 77% with only 36.5 mm in length, exhibiting stable bandwidth feature and large fabrication tolerance.
High-efficient and compact vertical grating coupler with achromatic in-plane metalens

Bo Xiong,Wei Ma,Weiping Wang,Xiaoyan Hu,Tao Chu

DOI: https://doi.org/10.1364/oe.467418

IF: 3.8

2022-01-01

Optics Express

Abstract:We proposed a new type of vertical grating couplers (VGCs) with a compact footprint on the 220-nm silicon-on-insulator platform. The overall size of the device containing the L-shaped coupling grating and the taper with achromatic in-plane metalens is only 45 × 15 µm2, and the measured coupling efficiency at 1550 nm is -5.2 dB with a 1 dB bandwidth of 38 nm, around 1.6 dB higher than the VGC without metalens. The incidence angle mismatch has a 1 dB bandwidth of roughly 4°, whereas the displacement mismatch along the x-/y- axis has a bandwidth of around 3/4 µm. Furthermore, we experimentally show that such a design is compatible with VGCs operating in the S, C, and L bands.
Ultracompact low-loss coupler between strip and slot waveguides.

Zhechao Wang,Ning Zhu,Yongbo Tang,Lech Wosinski,Daoxin Dai,Sailing He

DOI: https://doi.org/10.1364/OL.34.001498

IF: 3.6

2009-01-01

Optics Letters

Abstract:We present both theoretical and experimental results of an ultracompact waveguide coupler that is capable of highly efficient coupling of light from strip waveguides to slot waveguides, and vice versa. By optimizing the geometrical parameters, it is possible to achieve extremely low-loss coupling. A coupling efficiency of 97% has been obtained experimentally while keeping the overall size down to the range below 10 mu m. Further analysis shows that the proposed coupler has relatively high tolerance to fabrication errors and is wavelength insensitive. (C) 2009 Optical Society of America
Ultra-compact and Low-Loss Silicon Polarization Beam Splitter Using a Particle-Swarm-optimized Counter-Tapered Coupler.

Weiwei Chen,Bohao Zhang,Pengjun Wang,Shixun Dai,Wei Liang,Hongxiang Li,Qiang Fu,Jun Li,Yan Li,Tingge Dai,Hui Yu,Jianyi Yang

DOI: https://doi.org/10.1364/oe.408432

IF: 3.8

2020-01-01

Optics Express

Abstract:In this paper, an on-chip silicon polarization beam splitter using a particle-swarm-optimized counter-tapered directional coupler is proposed, designed, and fabricated. The coupling length of the proposed device is only 5 µm. As the waveguide width variation ΔW increases from -20 to 20 nm, the simulated polarization extinction ratio larger than 18.67 dB and the corresponding insertion loss lower than 0.17 dB are achieved. Measured experimental results achieved insertion loss <0.50 dB, TE polarization extinction between 16.68 to 31.87 dB, TM polarization extinction between 17.78 to 31.13 dB, over the wavelength range 1525 to 1600 nm.
Ultra-compact Silicon Mode (de)multiplexer Based on Directional Couplers with Subwavelength Sidewall Corrugations

Xiaofei Wang,Nannan Ning,Hui Yu,Yuehai Wang,Jianyi Yang

DOI: https://doi.org/10.1364/ol.449493

2021-01-01

Abstract:Asymmetrical directional couplers aided with subwavelength sidewall corrugations are used to realize ultra-compact silicon mode (de)multiplexers at C-band. Three mode (de)multiplexers with ultra-short coupling lengths of 5.6/6.5/7.7 μm are designed to enable low-loss mode conversions between TE0 and TE1/2/3 modes. They are then cascaded to build a four-channel mode-division-multiplexing (MDM) link. The four mode channels present minimal on-chip insertion losses of 0.2/0.7/0.7/0.9 dB at their peak wavelengths. Measured cross talk levels of the four mode channels are better than -18.0/-19.1/-16.0/-18.2 dB within the wavelength range from 1530 nm to 1580 nm.
Low-loss Grating Coupler with a Gradient Index-Matching Subwavelength Structure

Xiangyu Luo,Weijie Tang,Tao Chu

DOI: https://doi.org/10.1016/j.optlastec.2023.109860

2024-01-01

Abstract:O-band high-efficiency grating couplers were designed, and experimentally demonstrated with novel gradient index-matching subwavelength structures to reduce the leakage loss and mode mismatch. Trapezoidal subwavelength gratings and apodization were implemented to realize the change in the gradual effective index guided by the effective medium theory and improve the coupling efficiency. The grating couplers were fabricated with a simple single-step etching process. The measured lowest coupling losses of conventional rectangular and trapezoidal SWG grating couplers were -1.93 dB and -1.72 dB in the O-band, respectively. The latter result is the lowest reported losses of single-step etched grating couplers in the O-band with a minimum feature size of 120 nm, which is the typical minimum feature size in 130 nm CMOS node commercial silicon photonic processes.
Experimental Demonstration of Ultra-Compact Directional Couplers Based on Silicon Hybrid Plasmonic Waveguides

Fei Lou,Zhechao Wang,Daoxin Dai,Lars Thylen,Lech Wosinski

DOI: https://doi.org/10.1063/1.4729018

IF: 4

2012-01-01

Applied Physics Letters

Abstract:Hybrid plasmonic waveguides and directional couplers have been experimentally demonstrated. Using a direct measurement method, the propagation loss of a 170 nm wide waveguide is measured to be 0.08 dB/μm at 1550 nm when the thickness of low-index region is 56 nm. Ultra-compact directional couplers based on such hybrid plasmonic waveguides are demonstrated with gaps of 140 nm, 185 nm, 235 nm, and 290 nm. The corresponding coupling lengths measured are 1.55 μm, 2.2 μm, 3.2 μm, and 4.8 μm, respectively, which are in very good agreement with the simulations. These ultra-compact devices can be potentially used in future ultra-dense photonic integrated circuits.
Ultra-compact Photonic Crystal Couplers for Optical Switches Based on Band-Edge Resonance

Zheng Shuhui,Dong Guoyan,Yang Qingshan,Wang Huanhuan,Zhou Ji

DOI: https://doi.org/10.1007/s42114-021-00309-x

IF: 11.806

2021-01-01

Advanced Composites and Hybrid Materials

Abstract:Optical couplers play an important role in optical switches to split or combine light power in a predictable way. We proposed a novel scheme of photonic crystal (PhC) couplers relying on the unique characteristics of band-edge resonance. Stretched fundamental resonance can be excited in a square array of several periods to realize efficient transverse scattering. Two types of 1 × 2 and 2 × 1 PhC-couplers have been designed. The iconic features of ultra-compact constructure, ideal 3 dB splitting, and constant phase shift of 0/π prove the PhC-couplers are appropriate for splitters, combiners, and optical switches. Both numerical and experimental results validate that this PhC-coupling optical switch exhibits significant switching performances over a large variation of structural parameters. This work will be of interest for the development of optical components integration in micro-nano photonic circuits and related applications. Two types of 1 × 2 and 2 × 1 photonic crystal couplers have been proposed relying on stretched fundamental resonance near the photonic band edge. The iconic features of ultra-compact structure, ideal 3 dB splitting, and constant phase shift prove they are appropriate for the designs of splitters, combiners, and optical switches in optical components integration.
Compact Plasmonic Unidirectional Coupler with High Performance Based on an Asymmetric Slit-Groove Structure

Dalin Liu,Kun Li,Fan Lu,Chih-Chun Ho,Anshi Xu

DOI: https://doi.org/10.1109/jlt.2014.2368213

IF: 4.7

2014-01-01

Journal of Lightwave Technology

Abstract:A new scheme for unidirectional coupling of surface plasmon polaritons (SPPs) from freely propagating light into a metal-insulator-metal waveguide is proposed, which is composed of an asymmetric double-slit of different widths sandwiched by symmetric grooves. A theoretical model based on coupled-mode equations is developed to facilitate structure design and elucidate the underlying physical mechanism. With the model, the asymmetric double-slit with different widths is designed for unidirectional launching of SPPs with an ultrahigh extinction ratio of 44.8 dB at the wavelength 800 nm. A method of stepwise design is proposed for simplicity of design and convenience of analysis. Proof-of-principle demonstrations show that an ultrahigh extinction ratio of 37.1 dB and significant field enhancement for the proposed whole structure are obtained. In addition, an ultracompact plasmonic dichroic splitter based on the asymmetric double-slit with high extinction ratios of 24.2 and 21.8 dB at splitting wavelengths of 800 and 900 nm is achieved, and the lateral dimension of the plasmonic dichroic splitter is only 760 nm.
Ultra-low-loss optical interconnect enabled by topological unidirectional guided resonance

Haoran Wang,Yi Zuo,Xuefan Yin,Zihao Chen,Zixuan Zhang,Feifan Wang,Yuefeng Hu,Xiaoyu Zhang,Chao Peng

2023-06-15

Abstract:Grating couplers that interconnect photonic chips to off-chip components are of essential importance for various optoelectronics applications. Despite numerous efforts in past decades, existing grating couplers still suffer from poor energy efficiency and thus hinder photonic integration toward a larger scale. Here, we theoretically propose and experimentally demonstrate a method to achieve ultra-low-loss grating coupler by employing topological unidirectional guided resonances (UGRs). Leveraging the unidirectional emitting nature of UGRs, the useless downward radiation is greatly suppressed with no mirror placed on the bottom. By engineering the dispersion and apodizing the geometry of grating, we realize a grating coupler on 340 nm silicon-on-insulator platform with a record-low-loss of 0.34 dB and bandwidth exceeding 30 nm at the telecom wavelength of 1550 nm. We further show a pair of grating couplers works as optic via that interconnects two stacked photonic chips with a loss of only 0.94 dB. Our work sheds light on the feasibility of energy-efficient optical interconnect for silicon photonics, and paving the way to large-scale photonic integration for applications from optical communication to photonic computing.

Optics,Applied Physics

An Ultra-Compact Colorless 50:50 Coupler Based on Phc-Like Metamaterial Structure

A Multilayer Dual-Band Coupler Based on Composite Right/left-Handed Folded Substrate Integrated Waveguide

Ultracompact Fiber-to-Chip Metamaterial Edge Coupler

High-efficiency Grating Coupler Based on Fast Directional Optimization and Robust Layout Strategy in 130 Nm CMOS Process.

Compact and efficient coupler to interface hybrid dielectric-loaded plasmonic waveguide with silicon photonic slab waveguide

Single-step-etched ultra-compact metamaterial grating coupler enabled by a hierarchical inverse design approach

CMOS-Compatible Ultralow-Loss Three-Step Silicon Edge Coupler with Substrate Substitution in the Whole Communication Band

Asymmetric Plasmonic-Dielectric Coupler with Short Coupling Length, High Extinction Ratio, and Low Insertion Loss.

High-Efficiency Unidirectional Dual-Wavelength-Band Grating Coupler with 1D Subwavelength Structure

Compact broadband silicon 3 dB coupler based on shortcuts to adiabaticity.

Ltra-Compact Silicon Photonic Edge Coupler Based On Subwavelength Gratings

High-efficient and compact vertical grating coupler with achromatic in-plane metalens

Ultracompact low-loss coupler between strip and slot waveguides.

Ultra-compact and Low-Loss Silicon Polarization Beam Splitter Using a Particle-Swarm-optimized Counter-Tapered Coupler.

Ultra-compact Silicon Mode (de)multiplexer Based on Directional Couplers with Subwavelength Sidewall Corrugations

Low-loss Grating Coupler with a Gradient Index-Matching Subwavelength Structure

Experimental Demonstration of Ultra-Compact Directional Couplers Based on Silicon Hybrid Plasmonic Waveguides

Ultra-compact Photonic Crystal Couplers for Optical Switches Based on Band-Edge Resonance

Compact Plasmonic Unidirectional Coupler with High Performance Based on an Asymmetric Slit-Groove Structure

Ultra-low-loss optical interconnect enabled by topological unidirectional guided resonance