Abstract:High-textured pyrolytic carbon (PyC) is the ideal interface for SiC fiber-reinforced SiC matrix (SiCf/SiC) composites. To prepare high-textured PyC coatings on SiC fibers efficiently, chemical vapor deposition (CVD) technique was applied with the single precursor ethanol. The effects of CVD parameters on the morphology and textures of PyC were investigated in detail. Rough laminar (RL), smooth laminar (SL) and regenerative laminar (ReL) PyC could be obtained by controlling the CVD parameters. High-textured RL PyC could be stably synthesized in a large distance range in the horizontal tube furnace at 1150 °C and 10–20 kPa (total pressure), which inferred that low temperature and negative pressure were beneficial to the formation of RL PyC. Conversely, when the temperature was up to 1350 °C, the textures of PyC at different deposition positions varied considerably. In the vicinity of isothermal zone, the texture evolution of PyC with deposition positions followed the pattern of SL→RL→SL, which could be ascribed to the ratio change of the small linear hydrocarbons (fillers) and the aromatic hydrocarbons (particles) in the gas phase. The texture evolution followed the Particle-Filler model. In addition to PyC textures, the PyC coating thickness played a critical role in regulating the mechanical properties of SiC fibers and SiCf/SiC composites. In the present work, the effects of thickness of RL PyC coatings on the tensile properties of SiC fibers were investigated. The SiC fibers with 0.3 μm RL PyC coating showed the highest average tensile strength (2735 MPa) and Weilbull modulus (10.34), which might be ascribed to the repair of fiber surface defects and the appropriate stress state between fibers and coatings. The results could provide essential data for the interface design and optimization of SiCf/SiC composites.

Effect of CVD carbon coatings on properties of SiC fibres

Influence of SiC Coating Thickness on Mechanical Properties of SiCf/SiC Composite

Mechanical Behavior of SiCf/SiC Composites with Alternating PyC/SiC Multilayer Interphases

Influence of SiC Coating on Antioxidation Property of Carbon Fibers

Effect of the Incorporation of SiC Nanowire with Double Protective Layers on SiC Coating for C/C Composites

Effect of SiC Nanowires on the Mechanical and Oxidation Protective Ability of SiC Coating for C/C Composites

Measurement and Evaluation of the Tensile Strength of CVD SiC Fibers with Carbon Coating

Investigation on the properties of carbon fibre with C-Si functionally graded coating

Influence Of Sic Coating On The Oxidation Behavior Of Pan Carbon Fiber At Elevated Temperatures

Mechanical and thermal shock properties of C f /SiBCN composite: Effect of sintering densification and fiber coating

Influence of SiC Nanowires on the Properties of SiC Coating for C/C Composites Between Room Temperature and 1500°C

Synthesis of Coatings on SiC Fibers and Their Effects on Microstructure and Mechanical Properties of SiCf/SiBCN Composites

Texture control of pyrolytic carbon coatings and effects of coating thickness on the tensile properties of SiC fibers

Effects of Carbon Fiber Architecture on the Microstructure and Mechanical Property of C/C-SiC Composites

Effect of crystallinity of PAN-based carbon fiber surfaces on the formation characteristics of silicon carbide coating

Effect of SiC coating and heat treatment on damping behavior of C/SiC composites

Synthesis of nanostructured SiC coatings on carbon fibres by in situ reaction sintering with milled powders

Effect of the Incorporation of SiC Nanowire on Mullite/sic Protective Coating for Carbon/carbon Composites

Effects of PyC coating on SiC fibers after ultra-high temperature annealing

Mechanical and Thermal Shock Properties of Cf/SiBCN Composite: Effect of Sintering Densification and Fiber Coating

Interfacial Reactions and Mechanical Properties Studies of C-Coated and C/B4C Duplex-Coated SiC Fiber-Reinforced Ti2AlNb Composites