Abstract:In this study, the formation processes of TiC in a Cu–Ti–SiC system following the addition of a Ti–SiC mixture into a Cu melt were studied by analyzing the reaction intermediates, and the influence of the synthesis processes on the TiC microstructure was examined. It is found that, upon the addition of Ti–SiC into the Cu melt, the reaction of Ti and Cu to form a Cu–Ti liquid phase occurred first, followed by the reaction between liquid Ti, denoted as Ti(l), and SiC. However, the Ti(l)–SiC reaction processes vary depending on the reaction conditions and significantly influence the microstructures of the TiC particles, especially their dispersion in the Cu matrix. Under certain conditions, such as a lower reaction temperature and larger SiC size, SiC does not directly react with Ti(l). It first transforms into graphite through the outward diffusion of Si; subsequently, the graphite phase reacts with Ti(l) to form TiC. In this case, the synthesized TiC particles tend to connect with each other to form agglomerates. Under conditions conducive to the direct reaction of the Ti(l)–SiC system, such as a higher reaction temperature and smaller SiC size, Ti(l) and SiC first react to form a Ti3SiC2 phase that then decomposes into TiCx and Ti–Si phases and eventually transforms into TiCy (x > y) and amorphous or crystalline Si. In this case, the formed Ti–Si or Si phase can prevent the agglomeration of TiC particles, leading to their more uniform distribution in the prepared Cu matrix composite.

Effect of Cu-Ti-C Reaction Composition on Reinforcing Particles Size of TiCx/Cu Composites

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

The microstructures of in-situ synthesized TiC by Ti-CNTs reaction in Cu melts

Shape-Controlled TiCx Particles Fabricated by Combustion Synthesis in the Cu-Ti-C System

Study of the Synthesis Process of Non-Stoichiometric TiC in Cu-Ti Melts

The effect of carbon source and molar ratio in Fe–Ti–C system on the microstructure and mechanical properties of in situ TiC/Fe composites

Compression Properties and Electrical Conductivity of In-Situ 20 Vol.% Nano-Sized TiCx/Cu Composites with Different Particle Size and Morphology.

Effects of Process Parameters on Microstructure and Properties of TiC Reinforced Cu-Matrix Composites

Influence of TiC particle size on microstructural evolution and fracture mechanism of TiC/Al-Cu composites

Interaction of a Ti⁻Cu Alloy with Carbon: Synthesis of Composites and Model Experiments

Influence on TiC microstructure from different synthesis processes in the Cu–Ti–SiC system

Controlling the sizes of in-situ TiC nanoparticles for high-performance TiC/Al–Cu nanocomposites

Investigation on microstructure and properties of TiC0.5-Al2O3/Cu composites fabricated by a novel in-situ reactive synthesis

Influence of TiC Content on Microstructure and Properties of W-3OCu/TiC Composites

Influence of TiC Content on Microstructure and Properties of W-30Cu/TIC Composites

Effect of Ti–Cu alloy's composition on microstructure and performance of carbon fiber reinforced TiC-based composites prepared by alloyed reactive melt infiltration

Optimization of the mechanical properties of CNTs/Cu composite by regulating the size of interfacial TiC

Fabrication and Properties of Nano-TiCx/Cu-Cr-Zr Alloy Composites

Grain Refinement and Mechanical Properties of Cu-Cr-Zr Alloys with Different Nano-Sized TiCp Addition.

Combustion Synthesis of Tinxc1-X Powders with Ultra Fine Particle Size by Using Titanium Oxide As Dilution

The Reaction between Ti<sub>3</sub>AlC<sub>2</sub> and Cu in the Synthesis Process of Cu/Ti<sub>3</sub>AlC<sub>2</sub> Composites