Abstract:The optimal conditions for synthesizing a pure chalcopyrite CuFeS2 phase were thoroughly investigated through the combination of mechanical alloying (MA) and hot pressing (HP) processes. The MA process was performed at a rotational speed of 350 rpm for durations ranging from 6 to 24 h under an Ar atmosphere, ensuring proper mixing and alloying of the starting materials. Afterward, MA-synthesized chalcopyrite powder was subjected to HP at temperatures between 723 K and 823 K under a pressure of 70 MPa for 2 h in a vacuum. This approach aimed to achieve phase consolidation and densification. A thermal analysis via differential scanning calorimetry (DSC) revealed distinct endothermic peaks at the range of 740–749 K and 1169–1170 K, corresponding to the synthesis of the chalcopyrite phase and its melting point, respectively. An X-ray diffraction (XRD) analysis confirmed the successful synthesis of the tetragonal chalcopyrite phase across all samples. However, a minor secondary phase, identified as Cu1.1Fe1.1S2 (talnakhite), was observed in the sample hot-pressed at the highest temperature of 823 K. This secondary phase could result from slight compositional deviations or local phase transformations at elevated temperatures. The thermoelectric properties of the CuFeS2 samples were evaluated as a function of the HP temperatures. As the HP temperature increased, the electrical conductivity exhibited a corresponding rise, likely due to enhanced densification and reduced grain boundary resistance. However, this increase in electrical conductivity was accompanied by a decrease in both the Seebeck coefficient and thermal conductivity. The reduction in the Seebeck coefficient could be attributed to the higher carrier concentration resulting from improved electrical conductivity, while the decrease in thermal conductivity was likely due to reduced phonon scattering facilitated by the grain boundaries. Among the samples, the one that was hot-pressed at 773 K displayed the most favorable thermoelectric performance. It achieved the highest power factor of 0.81 mWm−1K−1 at 523 K, indicating a good balance between the Seebeck coefficient and electrical conductivity. Additionally, this sample achieved a maximum figure-of-merit (ZT) of 0.32 at 723 K, a notable value for chalcopyrite-based thermoelectric materials, indicating its potential for mid-range temperature applications.

Preparation of Tetrahedrite Cu 12 Sb 4 S 13 by Mechanical Alloying and Hot Pressing

Electronic Transport and Thermoelectric Properties of Cu12-xZnxSb4S13 Tetrahedrites Prepared by Mechanical Alloying and Hot Pressing

Solid-State Synthesis and Thermoelectric Properties of Tetrahedrites Cu12Sb4-yBiyS13

Thermoelectric Properties of Mechanically-Alloyed and Hot-Pressed Cu12−xCoxSb4S13 Tetrahedrites

Thermal Stability and Mechanical Properties of Thermoelectric Tetrahedrite Cu 12 Sb 4 S 13

Thermal Stability, Mechanical Properties and Thermoelectric Performance of Cu11TrSb4S13 (tr = Mn, Fe, Co, Ni, Cu, and Zn)

Synthesis of Fe-Doped Tetrahedrites Cu<sub>12-x</sub>Fe<sub>x</sub>Sb<sub>4</sub>S<sub>13</sub> and Characterization of Their Thermoelectric Properties

Powder Metallurgically Synthesized Cu12Sb4S13tetrahedrites: Phase Transition and High Thermoelectricity

Bytizite Cu3SbSe3: Solid-State Synthesis and Thermoelectric Performance

Chalcopyrite CuFeS2: Solid-State Synthesis and Thermoelectric Properties

Texture Development and Grain Alignment of Hot‐Pressed Tetradymite Bi 0.48 Sb 1.52 Te 3 Via Powder Molding

Thermoelectric and Transport Properties of Permingeatite Cu3SbSe4 Prepared Using Mechanical Alloying and Hot Pressing

Thermoelectric and Transport Properties of Permingeatite Cu<sub>3</sub>SbSe<sub>4</sub> Prepared Using Mechanical Alloying and Hot Pressing

Electronic Transport and Thermoelectric Properties of Te-Doped Tetrahedrites Cu12Sb4-yTeyS13

Process Controls for Bi 2 Te 3 -Sb 2 Te 3 Prepared by Mechanical Alloying and Hot Pressing

Charge Transport and Thermoelectric Properties of Mn-Doped Tetrahedrites Cu<sub>12</sub><sub>-x</sub>Mn<sub>x</sub>Sb<sub>4</sub>S<sub>13</sub>

Fabrication and Mechanical Properties of High-Pure Ti<sub>3</sub>SiC<sub>2</sub> Bulk Materials Directly by Hot-Pressing its Powder

Fabrication and mechanical properties of high-pure Ti3SiC 2 bulk materials directly by hot-pressing its powder

Hydrothermally Synthesized and Hot-Pressed Bi-2(Te,Se)(3) Thermoelectric Alloys

Effects of Aging on Thermoelectric Properties of Tetrahedrite Cu 12 Sb 4 S 13

Skinnerite Cu3SbS3: Solid-State Synthesis and Thermoelectric Properties