Abstract:Micro-EDM is an unconventional technology used to machine every type of electrically conductive material regardless of its mechanical properties. Material removal occurs through electrical discharges between the workpiece and the electrode immersed in a dielectric fluid. In drilling operations, the technology is able to realise microholes with excellent quality in terms of precision, quality surface, roundness, and taper to the detriment of the machining time, which is less than other technologies. Several efforts are being made to improve different features related to the process performance that are severely affected by both the operative conditions, such as the electrode material or the type of dielectric, and process parameters. The typical indexes used to characterise the performance are the machining time, the material removal rate, and the geometric indexes. These indexes are very effective and are easily measurable, but they do not give information about the evolution of the drilling process, which could be irregular due to the different phenomena occurring during machining. The aim of this paper is the development of a method able to elaborate the motion law of the electrode during the micro-EDM drilling operation. In order to do this, a single hole was manufactured in several steps, recording both the machining time and electrode wear for each step. In this way, the actual position of the electrode during the drilling can be measured without the use of a predictive model for electrode wear. It was tested to confirm that the multistep procedure did not introduce new phenomena, in contrast to the traditional drilling operation. This method was used to study the effects of the electrode diameter, the type of electrode, the length of the electrode out of the spindle, and the entity of the run-out on the process performance. The tests were executed on titanium alloy sheets using a tungsten carbide electrode and hydrocarbon oil as the dielectric. It was found that the descent of the electrode into the workpiece was not regular, but it depended on the level of debris concentration in the machining zone. The debris concentration was influenced by the type and diameter of the electrode, its length out of the spindle, and, to a lesser extent, the run-out. This method was found to be a useful method for an in-depth analysis of the micro-EDM drilling process, contributing to a better understanding of the physical aspects of the process.

Influence of Alternating Side Gap on Micro-Hole Machining Performances in Micro-Edm

Study of Alternating Current Flow in Micro-Edm Through Real-Time Pulse Counting

An Investigation into Accumulative Difference Mechanism in Time and Space for Material Removal in Micro-EDM Milling

An Analysis of the Uneven Tool Electrode Wear Mechanism in the Micro-electrical Discharge Machining Process

Interelectrode gas–liquid-solid three-phase flow analysis and simulation for drilling holes with high aspect ratio by micro-EDM

Simulation Study on Gap Flow Field in EDM Micro-hole Machining Based on Gas-liquid-solid Three-phase Flow

Micro-EDM of micro-stepped hole based on the wear of micro-bit

Gap status identification and control of wire electrochemical micromachining

Performance improvement of high-speed EDM and ECM combined process by using a helical tube electrode with matched internal and external flushing

Influence of Electrolytic Products in Machining Gap on Micro ECM

A High Energy Density Pulsed Power Supply for Micro EDM of High Aspect Ratio Holes

The effect of ultrasonic amplitude on the performance of ultrasonic vibration-assisted EDM micro-hole machining

Study of the Law Motion of the Micro-EDM Drilling Process

Multiphysics Research on Electrochemical Machining of Micro Holes with Internal Features

A novel ultrasonic vibration-assisted micro-EDM method to improve debris removal performance using relative three-dimensional ultrasonic vibration (RTDUV)

Impact Analysis of Electrolyte Pressure on Shape Accuracy of Micro Holes in ECM with Hollow Electrodes

Effects of Thin Pipe Electrodes with Grooves in Small Deep Hole EDM

Improvement of ultrasonic cavitation and pumping effect in microhole EDM

A novel EDM method using longitudinal-torsional ultrasonic vibration (LTV) electrodes to improve machining performance for micro-holes

A Study on the Influence of Central Edge Absence in Helical Grinding for Micro-Hole Fabrication

Experimental study on the influence of workpiece shape on discharge gap and burr in LS-WEDM and the preparation of microelectrode array with specific size