Abstract:Silica-based ceramic cores are widely used in the manufacturing of hollow, nickel-based, superalloy turbine blades. However, elemental Hf, Ti, Al, and other active metals in the superalloy can react with silica-based ceramic cores during casting, resulting in a reduction in the quality of the turbine blades. In this study, both plasma spraying and sol-gel dipping methods were used to prepare alumina coatings on silica-based ceramic substrates to prevent the interfacial reaction. The performance of the alumina coatings prepared by both methods was evaluated by comparative analysis of the surface roughness, bonding interface morphologies, and the adhesive characteristics of the coating. The plasma-sprayed alumina coating has a roughness greater than 5 μm and peeled away from the substrate due to the difference in thermal expansion between SiO2 and Al2O3 at temperatures above 1500 °C, rendering the silica-based substrate with the plasma-sprayed alumina coating unfit for the application requirements of the casting process. The alumina coating prepared by the sol-gel dipping method improved the roughness of the substrate from Ra 2.39 μm to Ra 1.83 μm, and no peeling was observed when heated to 1550 °C for 30 min due to the pinning characteristics of the coating on the substrate. Furthermore, the interfacial reaction between the DZ125 superalloy melt and the silica-based substrate coated with alumina by sol-gel dipping method were investigated. The alumina coating effectively inhibited the interfacial reaction and no reaction products were detected during the directional solidification with pouring temperature of 1550 °C and withdraw rate of 5 mm/min. While a uniform, 4–5 μm thick HfO2 reaction layer formed between the uncoated substrate and the DZ125 alloy melt. Two dipping-drying cycles were required to ensure the alumina sol completely covered the surface of the substrate.

Modification of Ceramic Shell Facecoat for Inhibition of Sand Burning Defect on DZ22B Directionally Solidified Blades

Formation Mechanism and Restraining Measures of Burning-on of DZ22B Directionally Solidified Blade

Investigation of Fused Alumina Based-Mold Facecoats for DZ22B Directionally Solidified Blades

Dependence of Microstructural Evolution on the Geometric Structure for Serviced DZ125 Turbine Blades

Microstructure Evolution and Mechanical Behaviors of Alumina-Based Ceramic Shell for Directional Solidification of Turbine Blades

Properties of alumina coatings prepared on silica-based ceramic substrate by plasma spraying and sol-gel dipping methods

Feasibility Study of Microscale Laser Shock Processing Without Absorbing Coating to Improve High-Cycle Fatigue Performance of DZ17G Directionally Solidified Superalloy

Surface modification of IN713 LC superalloy with Metco 204NS by laser surface alloying

Mechanical Performance of Laser Deposition Repairing of in 738 on Directionally Solidified Superalloy Blade

Carbide Evolution of a Directionally Solidified Ni-Based Superalloy During Long-Term Exposure

Effect of Carbides on Interfacial Reactions Between Superalloy DZ40M and Ceramic Mold in Directional Solidification

Synthesis, protection performance, and failure analysis of α-Al2O3/Mo(Si,Al)2 coatings

High Temperature Performance of Laser Deposition GH105 Layers on Nickel Base Super Alloy Blade

Surface Quality Studies with Respect to Grinding Burn of New Typical Nickel-Based Superalloy

The Analysis on the Low Cycle Fatigue Behavior of A Directionally Solidified Superalloy with Recrystallized Surface Layers

Microstructure and Mechanical Property of a Directional Ni-Based Superalloy During Long-Term Exposure

Epitaxial growth and oxidation behavior of the NiCoCrAlYTa/Y2O3 coating on a nickel-based single-crystal superalloy blade tips, produced by electro spark deposition

Ablation Mechanism of AlSiB-C/C Composites under an Oxy-Acetylene Torch

Effect of Directional Solidification Methods on the Cast Microstructure and Grain Orientation of Blade Shaped Dz125 Superalloy

Grinding Burn Mechanism of Directionally Solidified Superalloy

The Effect of Pulling Speed on the Structure and Properties of DZ22B Superalloy Blades