Low cycle fatigue behavior and life prediction of a directionally solidified alloy
Behnam Salehnasab,Sarvnaz Hashem-Sharifi
DOI: https://doi.org/10.62676/ygye8n63
2024-03-14
Abstract:Alloys used in engines are subjected to challenging environments characterized by thermal and mechanical cyclic loadings during start-up and shut-down processes. These conditions can significantly increase the occurrence of fatigue failure mechanisms. Therefore, this study focuses on investigating the low cycle fatigue (LCF) behavior of directionally-solidified alloy at two distinct temperatures, namely 600 °C and 800 °C. Strain-controlled LCF tests were conducted at the specified temperatures, utilizing constant total strain amplitudes of 0.4%, 0.6%, 0.8%, and 1% under a totally reversed loading ratio (R = -1). The Coffin-Manson model, based on plastic deformation, along with a hysteresis energy-based criterion model, were employed to predict and evaluate fatigue life and LCF behavior. Notably, the hysteresis energy and Coffin-Manson models exhibited superior capability in predicting LCF life at 800 °C compared to 600 °C. REFERENCES Salehnasab, J. Marzbanrad, E. Poursaeidi, Transient thermal fatigue crack propagation prediction in a gas turbine component, Eng. Fail. Anal. 130 (2021) 105781. https://doi.org/10.1016/j.engfailanal.2021.105781. S.K. Balam, M. Tamilselvi, A.K. Mondal, R. Rajendran, An investigation into the cracking of platinum aluminide coated directionally solidified CM247 LC high pressure nozzle guide vanes of an aero engine, Eng. Fail. Anal. 94 (2018) 24–32. https://doi.org/10.1016/j.engfailanal.2018.07.027. M. Martinez-Esnaola, M. Arana, J. Bressers, J. Timm, A. Martin-Meizoso, A. Bennett, E.E. Affeldt, Crack initiation in an aluminide coated single crystal during thermomechanical fatigue, ASTM Spec. Tech. Publ. 1263 (1996) 68–81. https://doi.org/10.1520/STP16447S. Schlesinger, T. Seifert, J. Preussner, Experimental investigation of the time and temperature dependent growth of fatigue cracks in Inconel 718 and mechanism based lifetime prediction, Int. J. Fatigue. 99 (2017) 242–249. https://doi.org/10.1016/j.ijfatigue.2016.12.015. Furrer, H. Fecht, Ni-based superalloys for turbine discs, Jom. 51 (1999) 14–17. https://doi.org/10.1007/s11837-999-0005-y. Salehnasab, D. Zarifpour, J. Marzbanrad, G. Samimi, An Investigation into the fracture behavior of the IN625 hot-rolled superalloy, J. Mater. Eng. Perform. 30 (2021) 7171–7184. https://doi.org/https://doi.org/10.1007/s11665-021-05895-x. Caron, T. Khan, Evolution of Ni-based superalloys for single crystal gas turbine blade applications, Aerosp. Sci. Technol. 3 (1999) 513–523. https://doi.org/10.1016/S1270-9638(99)00108-X. Slámečka, J. Pokluda, M. Kianicová, J. Horníková, K. Obrtlík, Fatigue life of cast Inconel 713LC with/without protective diffusion coating under bending, torsion and their combination, Eng. Fract. Mech. 110 (2013) 459–467. https://doi.org/10.1016/j.engfracmech.2013.01.001. Rajendran, M.D. Ganeshachar, T.M. Rao, Condition assessment of gas turbine blades and coatings, Eng. Fail. Anal. 18 (2011) 2104–2110. https://doi.org/10.1016/j.engfailanal.2011.06.017. K. Bhaumik, M. Sujata, M.A. Venkataswamy, M.A. Parameswara, Failure of a low pressure turbine rotor blade of an aeroengine, Eng. Fail. Anal. 13 (2006) 1202–1219. https://doi.org/10.1016/j.engfailanal.2005.12.002. F. Nie, Z.L. Liu, X.M. Liu, Z. Zhuang, Size effects of γ′ precipitate on the creep properties of directionally solidified nickel-base super-alloys at middle temperature, Comput. Mater. Sci. 46 (2009) 400–406. https://doi.org/10.1016/j.commatsci.2009.03.023. Min, X. Wu, L. Xu, W. Tang, S. Zhang, G. Wallner, D. Liang, Y. Feng, Influence of different surface treatments of H13 hot work die steel on its thermal fatigue behaviors, J. Shanghai Univ. (English Ed. 5 (2001) 326–330. https://doi.org/10.1007/s11741-001-0049-x. K. Rai, J.K. Sahu, S.K. Das, N. Paulose, D.C. Fernando, C. Srivastava, Cyclic plastic deformation behaviour of a directionally solidified nickel base superalloy at 850° C: damage micromechanisms, Mater. Charact. 141 (2018) 120–128. https://doi.org/10.1016/j.matchar.2018.04.039. Zhang, L.G. Zhao, A. Roy, V. V Silberschmidt, G. Mccolvin, Low-cycle fatigue of single crystal nickel-based superalloy–mechanical testing and TEM characterisation, Mater. Sci. Eng. A. 744 (2019) 538–547. https://doi.org/10.1016/j.msea.2018.12.084. Qu, C.M. Fu, C. Dong, J.F. Tian, Z.F. Zhang, Failure analysis of the 1st stage blades in gas turbine engine, Eng. Fail. Anal. 32 (2013) 292–303. https://doi.org/10.1016/j.engfailanal.2013.03.017. Salehnasab, E. Poursaeidi, S.A. Mortazavi, G.H. Farokhian, Hot corrosion failure in the first stage nozzle of a gas turbine engine, Eng. Fail. Anal. 60 (2016). https://doi.org/10.1016/j.engfailanal.2015.11.057. Kumari, D.V. V Satyanarayana, M. Srinivas, Failure analysis of gas turbine rotor blades, Eng. Fail. Anal. 45 (2014) 234–244. https://doi.org/10.1016/j.engfailanal.2014.06.003. J. Carter, Common failures in gas turbine blades, Eng. Fail. Anal. 12 (2005) 237–247. https://doi.org/10.1016/j.engfailanal.2004.07.004. Salehnasab, E. Poursaeidi, Mechanism and modeling of fatigue crack initiation and propagation in the directionally solidified CM186 LC blade of a gas turbine engine, Eng. Fract. Mech. 225 (2020) 106842. https://doi.org/10.1016/j.engfracmech.2019.106842. I. Stephens, A. Fatemi, R.R. Stephens, H.O. Fuchs, Metal fatigue in engineering, John Wiley & Sons, 2000. Salehnasab, J. Marzbanrad, E. Poursaeidi, Conventional shot peening treatment effects on thermal fatigue crack growth and failure mechanisms of a solid solution alloy, Eng. Fail. Anal. 155 (2024) 107740. https://doi.org/10.1016/j.engfailanal.2023.107740. Prasad, R. Sarkar, P. Ghosal, V. Kumar, M. Sundararaman, High temperature low cycle fatigue deformation behaviour of forged IN 718 superalloy turbine disc, Mater. Sci. Eng. A. 568 (2013) 239–245. https://doi.org/10.1016/j.msea.2012.12.069. Cano, J.A. Rodríguez, J.M. Rodríguez, J.C. García, F.Z. Sierra, S.R. Casolco, M. Herrera, Detection of damage in steam turbine blades caused by low cycle and strain cycling fatigue, Eng. Fail. Anal. 97 (2019) 579–588. https://doi.org/10.1016/j.engfailanal.2019.01.015. Gao, C. Fei, G. Bai, L. Ding, Reliability-based low-cycle fatigue damage analysis for turbine blade with thermo-structural interaction, Aerosp. Sci. Technol. 49 (2016) 289–300. https://doi.org/10.1016/j.ast.2015.12.017. Gustafsson, J.J. Moverare, S. Johansson, K. Simonsson, M. Hörnqvist, T. Månsson, S. Sjöström, Influence of high temperature hold times on the fatigue crack propagation in Inconel 718, Int. J. Fatigue. 33 (2011) 1461–1469. https://doi.org/10.1016/j.ijfatigue.2011.05.011. M. Seo, I.S. Kim, C.Y. Jo, Low Cycle Fatigue and Fracture Behavior of Nickel-Base Superalloy CM247LC at 760° C, in: Mater. Sci. Forum, Trans Tech Publ, 2004: pp. 561–564. https://doi.org/10.4028/www.scientific.net/MSF.449-452.561. D. Antolovich, S. Liu, R. Baur, Low cycle fatigue behavior of René 80 at elevated temperature, Metall. Trans. A. 12 (1981) 473–481. https://doi.org/10.1007/BF02648545. He, Y. Zhang, W. Qiu, H.-J. Shi, J. Gu, Temperature effect on the low cycle fatigue behavior of a directionally solidified nickel-base superalloy, Mater. Sci. Eng. A. 676 (2016) 246–252. https://doi.org/10.1016/j.msea.2016.08.064. He, Q. Zheng, X. Sun, H. Guan, Z. Hu, K. Tieu, C. Lu, H. Zhu, Effect of temperature and strain amplitude on dislocation structure of M963 superalloy during high-temperature low cycle fatigue, Mater. Trans. 47 (2006) 67–71. https://doi.org/10.2320/matertrans.47.67. Deng, J. Xu, Y. Hu, Z. Huang, L. Jiang, Isothermal and thermomechanical fatigue behavior of Inconel 718 superalloy, Mater. Sci. Eng. A. 742 (2019) 813–819. https://doi.org/10.1016/j.msea.2018.11.052. J. Kashinga, L.G. Zhao, V. V Silberschmidt, F. Farukh, N.C. Barnard, M.T. Whittaker, D. Proprentner, B. Shollock, G. McColvin, Low cycle fatigue of a directionally solidified nickel-based superalloy: Testing, characterisation and modelling, Mater. Sci. Eng. A. 708 (2017) 503–513. https://doi.org/10.1016/j.msea.2017.10.024. Mukherjee, K. Barat, S. Sivaprasad, S. Tarafder, S.K. Kar, Elevated temperature low cycle fatigue behaviour of Haynes 282 and its correlation with microstructure–Effect of ageing conditions, Mater. Sci. Eng. A. 762 (2019) 138073. https://doi.org/10.1016/j.msea.2019.138073. V. Rao, N.C.S. Srinivas, G.V.S. Sastry, V. Singh, Low cycle fatigue, deformation and fracture behaviour of Inconel 617 alloy, Mater. Sci. Eng. A. 765 (2019) 138286. https://doi.org/10.1016/j.msea.2019.138286. Harris, G.L. Erickson, R.E. Schwer, MAR-M247 derivations—CM247 LC DS alloy, CMSX single crystal alloys, properties and performance, Superalloys. 1984 (1984) 221–230. https://doi.org/10.7449/1984/SUPERALLOYS_1984_221_230. -C. Zhao, J.H. Westbrook, Ultrahigh-temperature materials for jet engines, MRS Bull. 28 (2003) 622–630. https://doi.org/10.1557/mrs2003.189. S. Fan, X.G. Yang, D.Q. Shi, S.W. Han, S.L. Li, A quantitative role of rafting on low cycle fatigue behaviour of a directionally solidified Ni-based superalloy through a cross-correlated image processing method, Int. J. Fatigue. 131 (2020) 105305. https://doi.org/10.1016/j.ijfatigue.2019.105305. Radonovich, A.P. Gordon, Methods of extrapolating low cycle fatigue data to high stress amplitudes, 2008. https://doi.org/10.1115/GT2008-50365. R. Daubenspeck, A.P. Gordon, Extrapolation techniques for very low cycle fatigue behavior of a Ni-base superalloy, (2011). https://doi.org/10.1115/1.4003602. Nagarjuna, M. Srinivas, K. Balasubramanian, D.S. Sarmat, Effect of alloying content on high cycle fatigue behaviour of Cu Ti alloys, Int. J. Fatigue. 19 (1997) 51–57. https://doi.org/10.1016/S0142-1123(96)00041-2. Lai, T. Lund, K. Rydén, A. Gabelli, I. Strandell, The fatigue limit of bearing steels–Part I: A pragmatic approach to predict very high cycle fatigue strength, Int. J. Fatigue. 38 (2012) 155–168. https://doi.org/10.1016/j.ijfatigue.2011.09.015. V.U. Praveen, V. Singh, Effect of cold rolling on the Coffin–manson relationship in low-cycle fatigue of superalloy IN718, Metall. Mater. Trans. A. 39 (2008) 79–86. https://doi.org/10.1007/s11661-007-9378-0. Suresh, Fatigue of materials, Cambridge university press, 1998. Liu, Z.J. Zhang, P. Zhang, Z.F. Zhang, Extremely-low-cycle fatigue behaviors of Cu and Cu–Al alloys: Damage mechanisms and life prediction, Acta Mater. 83 (2015) 341–356. https://doi.org/10.1016/j.actamat.2014.10.002. Xue, A unified expression for low cycle fatigue and extremely low cycle fatigue and its implication for monotonic loading, Int. J. Fatigue. 30 (2008) 1691–1698. https://doi.org/10.1016/j.ijfatigue.2008.03.004. Kang, H. Ge, Predicting ductile crack initiation of steel bridge structures due to extremely low-cycle fatigue using local and non-local models, J. Earthq. Eng. 17 (2013) 323–349. https://doi.org/10.1080/13632469.2012.746211. W. Shao, P. Zhang, R. Liu, Z.J. Zhang, J.C. Pang, Z.F. Zhang, Low-cycle and extremely-low-cycle fatigue behaviors of high-Mn austenitic TRIP/TWIP alloys: Property evaluation, damage mechanisms and life prediction, Acta Mater. 103 (2016) 781–795. https://doi.org/10.1016/j.actamat.2015.11.015. Miao, T.M. Pollock, J.W. Jones, Crystallographic fatigue crack initiation in nickel-based superalloy René 88DT at elevated temperature, Acta Mater. 57 (2009) 5964–5974. https://doi.org/10.1016/j.actamat.2009.08.022. G. Wang, J.L. Liu, T. Jin, X.F. Sun, Y.Z. Zhou, Z.Q. Hu, J.H. Do, B.G. Choi, I.S. Kim, C.Y. Jo, Deformation mechanisms of a nickel-based single-crystal superalloy during low-cycle fatigue at different temperatures, Scr. Mater. 99 (2015) 57–60. https://doi.org/10.1016/j.scriptamat.2014.11.026. J. Plumbridge, M.E. Dalski, P.J. Castle, High strain fatigue of a type 316 stainless steel, Fatigue Fract. Eng. Mater. Struct. 3 (1980) 177–188. https://doi.org/10.1111/j.1460-2695.1980.tb01112.x.