Abstract:For the past few years, research in the field of flow boiling heat transfer has gained immense popularity for unravelling the dominant mechanism responsible for controlling heat transfer and identifying a parametric trend for understanding the characteristics of flow boiling heat transfer. This has led to several assumptions and models for predicting heat transfer during flow boiling without any known generalized mechanism. This study therefore seeks to experimentally study the characteristics of heat transfer during flow boiling over a wide range but small increase in vapor quality from a single-phase subcooled region through to a two-phase superheated vapor region. The study was performed with an R134a refrigerant in a single horizontal circular stainless-steel smooth tube that had an internal diameter of 5 mm. In this experimental study, local heat transfer coefficients and frictional pressure drop were measured for low heat fluxes of 4.6–8.5 kW/m2, mass fluxes of 200–300 kg/(m2s), vapor quality from −0.1 to 1.2 and a low constant saturation pressure of 460 kPa. Flow patterns observed during the study were recorded with a high-speed camera at 2000 fps. In covering a wide range of vapor quality, a peak of heat transfer coefficient near a vapor quality of zero and a local minimum observed in the low vapor quality region were observed, and both were sensitive to heat flux and mildly sensitive to mass flux. Generally, at low vapor quality, the heat transfer coefficient deteriorated with vapor quality and this was sensitive to heat flux but insensitive to mass flux and vapor quality, indicating nucleate boiling dominance in low vapor quality regions. In high vapor quality regions, the heat transfer coefficient was sensitive to mass flux and insensitive to heat flux. This indicates the dominance of convective boiling. In the low vapor quality regions, the flow patterns observed were slug and intermittent, while in the high vapor quality region, annular and mist flow patterns were observed. Generally, frictional pressure drop increased with increasing mass flux and vapor quality in the two-phase region.

Heat Transfer Characteristics of Evaporation Process of High Pressure Freon R113 Liquids during Depressurization

Pressure Drop and Heat Transfer of Flow Boiling R134a in a Dimpled Flat Duct

Experimental Investigation on the Rapid Evaporation of High-Pressure R113 Liquid Due to Sudden Depressurization

Experimental Investigation on Rapid Evaporation of High-Pressure Liquids Due to Depressurization

Transient Heat Transfer Characteristics of Supercritical Fluid During Rapid Depressurization Process

Visualization of R1233zd(E) Flow Boiling in Parallel Mini-channels

Dynamics Of Evaporation And Cooling Of A Water Droplet During The Early Stage Of Depressurization

Evaporation Characteristics of Cis-1,1,1,4,4,4-hexafluoro-2-butene (r1336mzz(z)) Droplet in High Pressure and Temperature Environments

Experimental Investigation Evaporation Of Liquid Mixture Droplets During Depressurization And Into Air Stream

Evaporation Heat Transfer and Pressure Drop of R161 in A 7 Mm Micro-Fin Tube

Rapid Solidification Process of a Water Droplet Due to Depressurization

Boiling Heat Transfer Characteristics of the R744 Coolant in the Evaporator of the Separated Heat Pipe System

Experimental and Theoretical Investigation on Rapid Evaporation of Ethanol Droplets and Kerosene Droplets During Depressurization

Evaporation of a Sessile Water Droplet During Depressurization

Experimental Study on Depressurization of Freon at Supercritical Pressure

Heat Transfer And Pressure Drop During Evaporation Of R22 In Micro-Fin Tubes

Experimental Study on Liquid-Vapor Two-Phase Pressure Drop of Pulsating Flow in an Evaporator

Molecular dynamics simulation on phase transition behaviors of R410A liquid film over solid copper surface

Experimental Study of Horizontal Flow Boiling Heat Transfer Coefficient and Pressure Drop of R134a from Subcooled Liquid Region to Superheated Vapor Region

Frictional Pressure Drop Characteristics of R410A-Oil Flow Boiling in 7mm C-Shape Horizontal Smooth Tube

Heat and mass transfer characteristics of evaporation and salt crystallization process of a saline droplet during depressurization