Three-dimensional Analysis of Pedicle Screw Channel,screw Entry Point and Lateral Surface of Cervical Vertebral Body
李严兵,张韶辉,谢叻,陆声,周小兵,王爱平,陈志强,欧阳钧,钟世镇
DOI: https://doi.org/10.3969/j.issn.1674-666x.2010.02.006
2011-01-01
Abstract:Objective To explore three-dimensional relations of pedicle screw channel (PSC), screw entry point and lateral surface of cervical vertebral body by digital techniques. Methods CT scan images of cervical vertebra of 6 healthy adult were digitally analyzed by Mimics 10.01 software and their three-dimensional models were established. These data were saved as .stl format, then imported into UG Imageware 12.0 to perform computer aided design. Located at 3D coordinate system for the subject, the centrum was divided into 10 equal parts from front to back, and those 10 equal parts were taken as the standards of borderline depth. From front to back 10 equal parts mark lines on the centrum were determined to 100%-0% of borderline depth accordingly. The radius of inscribed circle, transverse screw angle (TSA) and PSC length in 90% borderline depth were gained, perpendicularity distances from best entering point to middle horizontal plane through pedicle, and to pedicle projection lateral borderline in 0o TSA of T3-T12 and to lateral borderline of lateral mass were determined respectively. Results 1. Inscribed circle radii of C3-C7 PSC increased gradually from 2.6 to 3.8 mm, radius of C7 PSC was biggest and that of C3 was smallest (left side: 2.6 mm, 2.7 mm, 2.9 mm, 3.1 mm, 3.4 mm; right side: 2.5 mm, 3.0 mm, 3.1 mm, 3.1 mm, 3.8 mm). 2. The lengths of C3-C7 PSC increased gradually from 23.8 to 28.2 mm, length of C7 PSC was biggest and that of C3 PSC was smallest (left side: 23.9 mm, 23.9 mm, 24.5 mm, 27.9 mm, 27.8mm; right side: 23.4 mm, 23.8 mm, 24.5 mm, 26.7 mm, 28.2 mm). 3. TSA scope of C3-C7 PSC was 33.2o-37.9o (left side: 33.2o, 33.1o, 35.0o, 35.3o, 33.5o; right side: 33.2o, 37.9o, 37.0o, 36.3o, 34.3o). 4. Perpendicularity distances from ideal screw entry point corresponding on the lamina surface to middle horizontal plane through pedicle of C3-C7 were measured respectively: left side:-0.5 mm, 0.8 mm,-0.3 mm,-0.4 mm,-0.5 mm; right side:-0.1 mm, 0.5 mm, 0.10 mm,-0.3 mm,-0.1 mm. The position of entry point was about 1 mm below reference plane. 5. The perpendicularity distances from ideal screw point corresponding on the lamina surface to pedicle projection lateral borderline were measured respectively: left side:-5.83 mm,-5.3 mm,-6. 9 mm,-5.7 mm,-2.7 mm; right side:-5.4 mm,-6.3 mm, 6.5 mm,-5.9 mm,-3.0 mm. The position of entry point to C3-C6 was 5-7 mm on the lateral side of pedicle projection lateral borderline, that of entry point to C7 was about 3 mm on the lateral borderline. 6. Perpendicularity distances from ideal screw entry point corresponding on the lamina surface to lamina mass lateral borderline of C3-C7 were measured respectively: left side: 4.1 mm, 4.8 mm, 3.6 mm, 2.7 mm, 3.8 mm; right side: 4.1 mm, 3.3 mm, 3.3 mm, 3.4 mm, 3.3 mm. The position of entry point to C3-C7 was 3-5 mm on the medial lamina mass borderline. Conclusion Pedicle projection lateral mass borderline and lamina lateral boundary are taken as reference mark lines for entering screw point of C3-C7, the position of best entering screw point of C3-C6 is outside of median line between two reference marks line, and that of C7 is inside of median line between two references marks line.