Abstract:Magnesium-zinc-calcium (Mg-Zn-Ca) alloys as a biomaterial have attracted much attention recently, owing to their excellent biocompatibility, similar mechanical properties to natural bone, and biodegradable properties. Despite the numerous advantages of MgZnCa alloys, the rapid degradation of magnesium proved challenging as the implant in unable to retain its structural integrity for a sufficient duration of time. For metallic glasses, the capability to produce a bulk sample that is sufficiently large for useful applications have been far less successful owing to challenging processing parameters that are required for rapid cooling. In this study, Mg65Zn30Ca5 melt-spun ribbons were produced using melt-spinning followed by spark plasma sintering under high pressure (60 MPa) at different temperatures (130–170 °C) to provide an insight into the consolidation, mechanical, and corrosion behavior. Microstructural interfaces were characterized using scanning electron microscopy while the thermal stability of the amorphous phase was characterized using differential scanning calorimetry and X-ray diffraction. Here, pellets with 10 mm diameter and 10 mm height with a complete amorphous structure were achieved at a sintering temperature of 150 °C with densification as high at ~98%. Sintering at higher temperatures, while achieving higher densification, resulted in the presence of nano-crystallites. The mechanical properties were characterized using microhardness and compression tests. The hardness values of the sintered products were relatively higher to those containing crystallite phases while the ultimate compressive strength increased with increasing sintering temperature. Bio-corrosion properties were characterized via electrochemical testing with PBS as the electrolyte at 37 °C. The corrosion results suggest that the sintered samples have a significantly improved corrosion resistance as compared to as-cast samples. More notably, SPS150 (samples sintered at 150 °C) exhibited the best corrosion resistance (35× compared to as-cast in the context of corrosion current density), owing to its single-phase amorphous nature. This study clearly shows the potential of spark plasma sintering in consolidating amorphous ribbons to near-full density bulk pellets with high corrosion resistance for bio-applications.

Amorphous magnesium alloy with high corrosion resistance fabricated by laser powder bed fusion

Laser printed amorphous magnesium alloy: Microstructure, mechanical properties and degradation behavior

In vivo biodegradation and biological properties of a Mg-Zn-Ca amorphous alloy for bone defect repair

Surface Engineering of Biodegradable Magnesium Alloys for Enhanced Orthopedic Implants.

A homogenous microstructural Mg-based matrix model for orthopedic application with generating uniform and smooth corrosion product layer in Ringer's solution: Study on biodegradable behavior of Mg-Zn alloys prepared by powder metallurgy as a case

Quasicrystal-strengthened biomedical magnesium alloy fabricated by laser additive manufacturing

Selective Laser Melted Rare Earth Magnesium Alloy with High Corrosion Resistance

Surface modification of biomedical Mg-Ca and Mg-Zn-Ca alloys using selective laser melting: Corrosion behaviour, microhardness and biocompatibility

An Amorphous Si-O-N Coating on Magnesium to Retard Corrosion & Improve Biocompatibility

Investigation on the preparation, microstructure, mechanical and degradation properties of laser additive manufactured Zn-Li-Mg alloy for bioresorbable application

Corrosion Resistance and Biocompatibility of Calcium Phosphate Coatings with a Micro-Nanofibrous Porous Structure on Biodegradable Magnesium Alloys

Pure Mg–Al Layered Double Hydroxide Film on Magnesium Alloys for Orthopedic Applications

A combined strategy to enhance the properties of Zn by laser rapid solidification and laser alloying

Laser Powder Bed Fusion of Biodegradable Magnesium Alloys: Process, Microstructure and Properties

Biodegradable magnesium alloy WE43 porous scaffolds fabricated by laser powder bed fusion for orthopedic applications: Process optimization, in vitro and in vivo investigation

The Characterization of a Biodegradable Mg Alloy after Powder Bed Fusion with Laser Beam/Metal Processing for Custom Shaped Implants

Study on Corrosion Characteristics and Mechanism of Laser Powder Bed Fusion of Mg-Zn-Zr Alloy

Development of Biocompatible Bulk MgZnCa Metallic Glass with Very High Corrosion Resistance in Simulated Body Fluid

Biodegradable and Bioactive Orthopedic Magnesium Implants with Multilayered Protective Coating.

Emergence of rapid solidification microstructure in additive manufacturing of a Magnesium alloy

In Vitro Corrosion and Cytocompatibility of A Microarc Oxidation Coating and Poly(L-Lactic Acid) Composite Coating on Mg-1li-1ca Alloy for Orthopedic Implants