Abstract:Abstract Scale-up studies of fluidized beds are important for numerous fields. Fluidization in a multi-ring inclined nozzle spout-fluid bed (MRIN spout-fluid bed) is one of the most critical factors that affect the coating efficiency and uniformity of tri-structural isotropic (TRISO) nuclear particles in the fluidized bed chemical vapor deposition (FB-CVD) process. In this work, the flow pattern similarity principle was proposed to scale up a specially designed spout-fluid bed, which was aimed at maintaining the gas-solid contact efficiency, and was validated by electrical capacitance tomography (ECT) measurements. First, the traditional ECT method was developed for the specially designed MRIN spout-fluid bed according to the filling method. Then, the reconstruction algorithms were updated using the alternating direction multiplier method (ADMM) by introducing optimization constraints. The fluidization laws were investigated for different superficial gas velocities and distributor structures. We found that the gas distributor structure affected the merge point of the jets, which played an essential role in fluidization pattern changes. The statistically-based coefficient of variation (Cv) was proposed to distinguish the different flow patterns. Multi-ring spouting was then selected as a typical flow pattern for good fluidization and mixing, where the Cv ranged from 0.25 to 0.65. Then, the optimal design principles for the enlarged spout-fluid bed gas distributor were obtained. We determined that a smaller nozzle diameter (0.71 d 0 ), larger nozzle spacing (1.12 x 0 ), and slightly inclined angle (1.50 θ 0 ) could improve fluidization, and that nozzle spacing was the most important factor. This study may be beneficial for the industrial design of the FB-CVD process and for the fabrication of high-density nuclear fuel particles. Additionally, it could be presented to a more general audience for scaling-up fluidized beds with a complex distributor, which would be beneficial for the fluidization research community.

Investigation of flow characteristics in a rectangular spouted fluidized bed using electrical capacitance volume tomography

Experimental and numerical investigation of solid behavior in a gas–solid turbulent fluidized bed

Particle Velocity Measurements in Transition Section of Turbulent Fluidized Beds Using Optical Fiber Probe and CFD Simulation

A Comparative Study of Electrostatic Current and Pressure Signals in a MSFC Gas–solid Fluidized Bed

CFD Simulation and Experiments of Dynamic Parameters in Gas–solid Fluidized Bed

Bubble Characterization in the Gas-Solid Fluidized Bed Using an Intrusive Acoustic Emission Sensor Array

Multi-scale Characteristics and Gas-Solid Interaction among Multiple Beds in a Dual Circulating Fluidized Bed Reactor System

Soft-sensing System of Gas-Solid Fluidized Bed

Experimental study on gas–solids flows in a circulating fluidised bed using electrical capacitance tomography

Experimental Investigation of Electrostatic Effect on Particle Motions in Gas-Solid Fluidized Beds

Study on Voidage Measurement of Gas-solid Fluidized Bed by Using Electrical Capacitance Tomography

Cfd-Dem Investigation of Particle Elutriation with Electrostatic Effects in Gas-Solid Fluidized Beds

Measurement of Flow Pattern and Bed Level of Gas-solid Fluidized Bed in Borstar Process by Acoustic Emission Technique

Simultaneous Measurement of Electrostatic Charge and Its Effect on Particle Motions by Electrostatic Sensors Array in Gas-Solid Fluidized Beds

Characterization of Particle Fluidization Pattern in a Gas Solid Fluidized Bed Based on Acoustic Emission (AE) Measurement

Measurement Of Gas-Solid Flow Pattern In Rectangle Cross-Section In Cfb By Electrical Capacitance Tomography

Imaging a rectangular fluidised bed by electrical capacitance tomography: Preliminary results

Characterization of Flow Intermittency and Coherent Structures in a Gas–Solid Circulating Fluidized Bed Through Electrostatic Sensing

Experimental study on the scale-up of a multi-ring inclined nozzle spout-fluid bed by electrical capacitance tomography

Investigation of Unstable Solids Circulation Behavior in A Circulating Fluidized Bed with Sweeping Bend Return Using Pressure Frequency Analysis

LES-DEM Investigation of Gas–solid Flow Dynamics in an Internally Circulating Fluidized Bed