Abstract:This study investigated the effect of adding La–Ce mixed rare earths and Sr on the microstructure and mechanical properties of AlSi10MnMg alloy. The experiment utilized different combinations of modifiers, including single La–Ce rare earths, single Sr, and the combined addition of La–Ce mixed rare earths and Sr. This study compared their effects on grain refinement, the modification of the α-Al phase and eutectic silicon phase, and tensile properties and hardness. The results showed that the combined modification of Sr and mixed rare earth elements significantly refined the grains, optimized the morphology of the α-Al phase and eutectic silicon phase, and improved the overall mechanical properties of the aluminum alloy. Under the combined modification, the addition of 0.02 wt.% Sr and 0.1 wt.% RE (La–Ce mixed rare earths) exhibited the most pronounced refining effect. The secondary dendrite arm spacing (SDAS) was reduced by 59.18%. The eutectic silicon phase transformed from coarse needle-like shapes to fine fibrous or granular forms, with an aspect ratio reduction of 69.39%. Meanwhile, the alloy's tensile strength and hardness were significantly improved. The tensile strength increased to 240 MPa, achieving an increase of 23.08%; the yield strength increased to 111 MPa, achieving an increase of 18.09%; and the elongation reached 7.3%, achieving an increase of 73.81%. This indicates that the proper addition of Sr and mixed rare earths can significantly optimize the microstructure and enhance the mechanical properties of AlSi10MnMg alloy, providing an effective method for the preparation of high-performance heat-treatment-free aluminum alloys.

Effect of Sc and Sr on the Eutectic Si Morphology and Tensile Properties of Al-Si-Mg Alloy

Influence of the interaction between Si and Sc on the microstructure and tensile properties of as casted Al-Si-Sc alloys

Modification mechanism and tensile property of Al-9Si-0.4Mg-0.1Cu alloy

Effect of Scandium on Grain refinement mechanism and Mechanical Properties of Al-7Si-0.6Mg alloy at Different Cooling Rates

Effect of Sr Modification on the Microstructures, Mechanical Properties, and Thermal Conductivity of Hypoeutectic Al-13.6Cu-6Si Alloys

Synergistic effect of Gd and Sr on the microstructure and mechanical properties of Al–Si–Mg alloy

Synergistic Effect of Sc and Excess Mg on the Microstructure and Mechanical Properties of Hypoeutectic Al-10Mg2Si Alloy

New Method of Eutectic Silicon Modification in Cast Al–Si Alloys

The Influence of the Combined Addition of La–Ce Mixed Rare Earths and Sr on the Microstructure and Mechanical Properties of AlSi10MnMg Alloy

The Effect of Solution Treatment on the Si Particles’ Morphology Evolution and the Thermal Conductivity and Tensile Properties of Sb-Modified Al-8Si-0.6Mg Alloys

Effect of Al‐10Sr Addition on Tensile and Wear Properties of 20 wt.%SiC/A359 Composites

Effect of Al-Sr-Y intermediate alloy on microstructure and mechanical properties of A356 alloy

EFFECT OF Sc ON MICROSTRUCTURE AND PROPERTIES OF Al-Li-Cu-Mg-Zr ALLOY

Grain refinement and eutectic modification of A356 casting alloy by adding Al-B-Sr master alloys and its effect on tensile properties

Effects of Sb, Sr, and Bi on the material properties of cast Al-Si-Cu alloys produced through heated mold continuous casting

Combined Treatment of Sr and B and Evaluation of Refinment-Modification Levels for Al-7si Casting Alloy

Influences of different Zr/Sc ratios on microstructure and mechanical properties of Al-2Si alloy

Allopurinol ribonucleoside as an antileishmanial agent. Biological effects, metabolism, and enzymatic phosphorylation.

Effects of Zr and Sr on microstructure and mechanical properties of cast Al–Si–Cu–Ni–Mg alloy

Effect of Cu and Sr on the Microstructure and Mechanical Properties of Al-Mg-Si Based Alloy Sheets

Influence of Alloying Element Mg on Na and Sr Modifying Al-7Si Hypoeutectic Alloy