Abstract:To synergistically improve the strength-ductility of copper alloys used in the miniaturized component, Cu-3.2Ti-0.2Fe-0.2V alloy with heterogeneous structure was obtained by thermo-mechanical treatment (namely, short-time annealing). The heterogeneous structure was composed of the non-uniform grains formed due to Laves phase inhibiting grain growth and FCC structured Cu4Ti phase with good coherent interface precipitated on the grain boundaries in sub-micro size. After aging at 400 °C for 2 h and then 450 °C for 4 h, the ultimate tensile strength and elongation of the heterogeneous-structured alloy were 976.8 MPa and 18.8% respectively, which was approximately 120 MPa more than that of the coarse-grained alloy after complete annealing, but both alloys had comparable ductility. When cold-rolling with 5% reduction was carried out before the aging of 450 °C, the strength increased to 1057 MPa and corresponding elongation was still over 10%. The strengthening mechanism of alloy with heterogeneous structure was analyzed and the hetero-deformation induced hardening of 284.5 MPa was the other significant reinforcement. The semi in-situ observation of tensile deformation behavior shown that the superior ductility in coarse-grained alloy was mainly attributed to the slipping and twinning. While grain rotation and grain boundary sliding were additional deformation mechanism in heterogeneous-structured alloy during tensile deformation, meanwhile, the texture of S, {110}<1 1 ‾ 1> and {331}<1 2 ‾ 3> components converted to the texture of {441}< 1 ‾ 1 ‾ 8>, Goss, Copper and {012}< 8 2 ‾ 1 > components. The deteriorative ductility after rolling with the reduction of 5% was owing to the S and Cube components converted to the strong texture of {032}<22 3 ‾ > components.

Microstructure Evolution and Hardness of an Ultra-High Strength Cu-Ni-Si Alloy During Thermo-Mechanical Processing

Microstructure and hot deformation behavior of the Cu-1Ni-0.9Sn-0.5Ti-0.3Cr alloy

Microstructure and Hardness Evolution During Isothermal Process at 700 °C for Fe–24Mn–0.7Si–1.0Al TWIP Steel

Microstructure and Texture Evolution of Novel Cu–10Ni–3Al–0.8Si Alloy During Hot Deformation

Hot Working Behavior of a Super High Strength Cu–Ni–Si Alloy

The Microstructure Evolution and Dynamic Recrystallization Mechanism of Cu-1.1–Ni-0.7–Co-0.45–Si-0.3Cr Alloys during High-Temperature Deformation

Microstructures and mechanical properties of Cu–Ti alloys with ultrahigh strength and high ductility by thermo-mechanical treatment

Microstructure and Texture Evolution of Cu-Ni-P Alloy after Cold Rolling and Annealing

Evolution of Microstructure, Texture, and Hardness in an Al-Cu-Mg Alloy During Annealing

Cold hardening and recrystallization temperature of Cu-Ni-Si-P alloy

Work Hardening Behavior and Microstructure Evolution of a Cu-Ti-Cr-Mg Alloy during Room Temperature and Cryogenic Rolling

Hot Deformation and Subsequent Annealing on the Microstructure and Hardness of an Al 0.3 CoCrFeNi High-entropy Alloy

Microstructure Evolution and Constitutive Modeling of Cu-Bearing High-Strength Low-Alloy Steel During Hot Deformation

Microstructure Evolution and Tensile Property of a CuMnFeCoNi High-Entropy Alloy During Thermomechanical Treatment

Microstructures and mechanical properties of Cu-Sn alloy subjected to elevated-temperature heat deformation

Microstructure and Hardness of Solution Treated and Cold-Rolled Co75Cr25 Alloy

Microstructure evolution of Cu-1.0Co-0.65Si-0.1Ti alloy during hot deformation

Microstructure evolution dependence of work-hardening characteristic in cold deformation of a difficult-to-deform nickel-based superalloy

Effect of Thermomechanical Processing on Microstructure and Mechanical Properties of CoCrFeNiMn High Entropy Alloy

Microstructural Evolution, Phase Transition, and Physics Properties of a High Strength Cu–Ni–Si–Al Alloy

High-temperature Deformation Behavior of Cu–6.0Ni–1.0Si–0.5Al–0.15 Mg–0.1Cr Alloy